標準號 |
中文名稱 |
英文名稱 |
| BS EN 1015-3-1999 |
磚石灰漿的試驗方法.新鮮灰漿連續性測定 |
(Methods of test for mortar for masonry - Determination of consistence of fresh mortar (by flow table)) |
| BS EN 1015-4-1999 |
磚石灰漿試驗方法.新鮮灰漿連續性的測定(傾倒?jié)B透法) |
(Methods of test for mortar for masonry - Determination of consistence of fresh mortar (by plunger penetration)) |
| BS EN 1015-6-1999 |
磚石灰漿試驗方法.新鮮灰漿集塊密度的測定 |
(Methods of test for mortar for masonry - Determination of bulk density of fresh mortar) |
| BS EN 1015-7-1999 |
磚石灰漿試驗方法.新鮮灰漿空氣含量的測定 |
(Methods of test for mortar for masonry - Determination of air content of fresh mortar) |
| BS EN 1015-9-1999 |
磚石灰漿試驗方法.新鮮灰漿使用壽命和校正時間的測定 |
(Methods of test for mortar for masonry - Determination of workable life and correction time of fresh mortar) |
| BS EN 10151-2002 |
彈簧用不銹鋼帶材.交貨技術條件 |
(Stainless steel strip for springs - Technical delivery conditions) |
| BS EN 10152-2003 |
電鍍鋅冷軋扁平鋼軋材.技術交貨條件 |
(Electrolytically zinc coated cold rolled steel flat products - Technical delivery conditions) |
| BS EN 10154-2002 |
連續熱浸鋁硅(AS)涂覆鋼條和鋼板.交貨技術條件 |
(Continuously hot-dip aluminium-silicon (AS) coated steel strip and sheet - Technical delivery conditions) |
| BS EN 10155-1993 |
改進的抗大氣腐蝕的結構鋼.交貨條件 |
(Structural steels with improved atmospheric corrosion resistance - Technical delivery conditions) |
| BS EN 10160-1999 |
厚度等于或大于6mm的鋼板制品的超聲檢驗(反射法) |
(Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method)) |
| BS EN 10162-2003 |
冷軋鋼型材.交貨技術條件.尺寸和橫截面公差 |
(Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances) |
| BS EN 10163-1-1991 |
熱軋鋼板材、寬扁材和型材表面條件供貨要求規范.第1部分:一般要求 |
(Specification for delivery requirements for surface condition of hot rolled steel plates, wide flats and sections - General requirements) |
| BS EN 10163-1-2004 |
熱軋鋼板材、寬扁材和型材表面條件交貨要求.一般要求 |
|
| BS EN 10163-2-1991 |
熱軋鋼制品表面狀態的供貨條件(薄板.寬扁鋼和異型鋼).第2部分:薄板和寬扁鋼 |
(Specification for delivery requirements for surface condition of hot rolled steel plates, wide flats and sections - Plates and wide flats) |
| BS EN 10163-2-2004 |
熱軋鋼板材、寬扁材和型材表面條件交貨要求.板材和寬扁材 |
|
| BS EN 10163-3-1991 |
熱軋鋼制品表面狀態的供貨條件(薄板.寬扁鋼和異型鋼)規范.第3部分:異型鋼 |
(Specification for delivery requirements for surface condition of hot rolled steel plates, wide flats and sections - Sections) |
| BS EN 10163-3-2004 |
熱軋鋼板材、寬扁材和型材表面條件交貨要求.型材 |
|
| BS EN 10164-1993 |
產品表面垂直變形特性改進的鋼產品.交貨技術條件 |
(Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions) |
| BS EN 10165-1996 |
非最終退火狀態下合金鋼制冷軋電工鋼片和鋼帶 |
(Cold rolled electrical alloyed steel sheet and strip delivered in the semi-processed state) |
| BS EN 10168-2004 |
鋼產品.檢查文件.信息和描述表 |
|
| BS EN 10169-1-1997 |
連續有機涂層(盤繞涂層)鋼板制品.一般信息(定義,材料,公差,測試方法) |
(Continuously organic coated (coil coated) steel flat products - General information (definitions, materials, tolerances, test methods)) |
| BS EN 10169-1-2004 |
連續有機涂覆(盤繞涂覆)的扁鋼制品.一般信息(定義、材料、公差、測試方法) |
|
| BS EN 10169-3-2003 |
連續有機涂層(盤繞涂層)變平鋼軋材.建筑物內部用品 |
(Continuously organic coated (coil coated) steel flat products - Products for building interior applications) |
| BS EN 1017-1998 |
飲用水處理用化學物質.半燒的白云石 |
(Chemicals used for treatment of water intended for human consumption - Half-burnt dolomite) |
| BS EN 1018-1998 |
飲用水處理用化學物質.碳化鈣 |
(Chemicals used for treatment of water intended for human consumption - Calcium carbonate) |
| BS EN 10184-1992 |
黑色金屬材料化學分析規范.鋼鐵中磷的測定.分光光度測定法 |
(Specification for chemical analysis of ferrous materials - Determination of phosphorus in steels and irons - Spectrophotometric method) |
| BS EN 1019-1996 |
人員用水的化學處理.二氧化硫 |
(Chemicals used for treatment of water intended for human consumption - Sulfur dioxide) |
| BS EN 1020-1998 |
與燃?xì)夂?或燃燒產物的輔助傳輸設備聯合使用的空間加熱凈加熱輸入功率不超過300KW的非家用燃?xì)鈴?qiáng)制對流空氣 |
(Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, incorporating a fan to assist transportation of combustion air and/or combustion produc) |
| BS EN 10200-1992 |
黑色金屬材料化學分析方法.用分光光度法測定鋼中的硼 |
(Chemical analysis of ferrous materials - Determination of boron in steel - Spectrophotometric method) |
| BS EN 10202-2001 |
冷縮電解鉻產品.電解錫板和電解鉻氧化涂層鋼 |
(Cold reduced tinmill products - Electrolytic tinplate and electrolytic chromium/chromium oxide coated steel) |
| BS EN 10204-1991 |
冶金產品.檢驗文件型式 |
(Metallic products - Types of inspection documents) |
| BS EN 10204-2004 |
金屬產品.檢驗文件的類型 |
|
| BS EN 10205-1992 |
生產鍍錫薄鋼板或鍍鎳鉻氧化層鋼板用冷軋黑色成卷薄鋼板 |
(Specification for cold reduced blackplate in coil form for the production of tinplate or electrolytic chromium/chromium oxide coated steel) |
| BS EN 10207-1992 |
簡單壓力容器用鋼材、板材、帶材和棒材供貨技術條件 |
(Steels for simple pressure vessels - Technical delivery requirements for plates, strips and bars) |
| BS EN 10208-1-1998 |
可燃性液體管線鋼管.技術提交條件.A級要求管 |
(Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Pipes of requirement class A) |
| BS EN 10208-2-1997 |
可燃流體用鋼管.技術交付條件.B級管要求 |
(Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Pipes of requirement class B) |
| BS EN 10209-1996 |
搪瓷用的冷軋低碳鋼板制品.交貨技術條件 |
(Cold rolled low carbon steel flat products for vitreous enamelling - Technical delivery conditions) |
| BS EN 1021-1-1994 |
家具.裝飾家具著火性的評估.火源:燃著的香煙 |
(Furniture - Assessment of the ignitability of upholstered furniture - Ignition source: smouldering cigarette) |
| BS EN 1021-2-1994 |
家具.裝飾家具著火性的評估.火源:等同于火柴的煤氣火焰 |
(Furniture - Assessment of the ignitability of upholstered furniture - Ignition source: match flame equivalent) |
| BS EN 10210-1-1994 |
非合金及精粒結構鋼的熱軋空心型材.交貨技術條件 |
(Hot finished structural hollow sections of non-alloy and fine grain structural steels - Technical delivery requirements) |
| BS EN 10210-2-1997 |
精粒結構鋼和非合金熱軋空心型材.公差,尺寸和部分特性 |
(Hot finished structural hollow sections of non-alloy and fine grain structural steels - Tolerances, dimensions and sectional properties) |
| BS EN 10211-1996 |
鋼鐵材料的化學分析.鋼和鐵中鈦含量測定.火焰原子吸收光譜測定法 |
(Chemical analysis of ferrous materials - Determination of titanium in steel and iron - Flame atomic absorption spectrometric method) |
| BS EN 10212-1996 |
生鐵材料的化學分析.用分光光度法測定鋼和鐵中的砷含量 |
(Chemical analysis of ferrous materials - Determination of arsenic in steel and iron - Spectrophotometric method) |
| BS EN 10213-1-1996 |
壓力用途的鋼鑄件交貨技術條件.概述 |
(Technical delivery conditions for steel castings for pressure purposes - General) |
| BS EN 10213-2-1996 |
壓力用途的鋼鑄件的交貨技術條件.第2部分:環境溫度和高溫下使用的鋼種 |
(Technical delivery conditions for steel castings for pressure purposes - Steel grades for use at room temperature and at elevated temperature) |
| BS EN 10213-3-1996 |
壓力用途的鋼鑄件交貨技術條件.低溫下使用的鋼 |
(Technical delivery conditions for steel castings for pressure purposes - Steels for use at low temperatures) |
| BS EN 10213-4-1996 |
壓力用途的鋼鑄件的交貨技術條件.第4部分:奧氏體和奧氏體-鐵素體鋼種 |
(Technical delivery conditions for steel castings for pressure purposes - Austenitic and austenitic-ferritic steel grades) |
| BS EN 10214-1995 |
連續熱浸鍍鋅鋁薄鋼板和鋼帶.交貨技術條件 |
(Continuously hot-dip zinc-aluminium (ZA) coated steel strip and sheet - Technical delivery conditions) |
| BS EN 10215-1995 |
連續熱浸鍍鋁鋅薄鋼板和鋼帶.交貨技術條件 |
(Continuously hot-dip aluminium-zinc (AZ) coated steel strip and sheet - Technical delivery conditions) |
| BS EN 10216-1-2002 |
壓力無縫鋼管.交貨技術條件.規定室溫特性的非合金鋼管 |
(Seamless steel tubes for pressure purposes - Technical delivery conditions - Non-alloy steel tubes with specified room temperature properties) |
| BS EN 10216-2-2002 |
壓力無縫鋼管.交貨技術條件.規定高溫特性的非合金和合金鋼管 |
(Seamless steel tubes for pressure purposes - Technical delivery conditions - Non-alloy and alloy steel tubes with specified elevated temperature properties) |
| BS EN 10216-3-2002 |
壓力無縫鋼管.交貨技術條件.合金細粒鋼管 |
(Seamless steel tubes for pressure purposes - Technical delivery conditions - Alloy fine grain steel tubes) |
| BS EN 10216-4-2002 |
壓力無縫鋼管.交貨技術條件.規定低溫特性的非合金和合金鋼管 |
(Seamless steel tubes for pressure purposes - Technical delivery conditions - Non-alloy and alloy steel tubes with specified low temperature properties) |
| BS EN 10216-5-2004 |
壓力無縫鋼管.交貨技術條件.無縫鋼管 |
|
| BS EN 10217-1-2002 |
壓力焊接鋼管.交貨技術條件.規定室溫特性的非合金鋼管 |
(Welded steel tubes for pressure purposes - Technical delivery conditions - Non-alloy steel tubes with specified room temperature properties) |
| BS EN 10217-2-2002 |
壓力焊接鋼管.交貨技術條件.規定高溫特性的非合金和合金電焊鋼管 |
(Welded steel tubes for pressure purposes - Technical delivery conditions - Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties) |
| BS EN 10217-3-2002 |
壓力焊接鋼管.交貨技術條件.合金細粒鋼管 |
(Welded steel tubes for pressure purposes - Technical delivery conditions - Alloy fine grain steel tubes) |
| BS EN 10217-4-2002 |
壓力焊接鋼管.交貨技術條件.規定低溫特性的非合金和合金電焊鋼管 |
(Welded steel tubes for pressure purposes - Technical delivery conditions - Electric welded non-alloy steel tubes with specified low temperature properties) |
| BS EN 10217-5-2002 |
壓力焊接鋼管.交貨技術條件.規定高溫特性的非合金和合金埋弧焊接鋼管 |
Welded steel tubes for pressure purposes - Technical delivery conditions - Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperature properties |
| BS EN 10217-6-2002 |
壓力焊接鋼管.交貨技術條件.規定低溫特性的非合金埋弧焊接鋼管 |
(Welded steel tubes for pressure purposes - Technical delivery conditions - Submerged arc welded non-alloy steel tubes with specified low temperature properties) |
| BS EN 10218-1-1994 |
鋼絲和線材制品.概述.試驗方法 |
Steel wire and wire products - General - Test methods |
| BS EN 10218-2-1997 |
鋼絲和線材制品.概述.線材尺寸和公差 |
Steel wire and wire products - General - Wire dimensions and tolerances |
| BS EN 10219-1-1997 |
精粒結構鋼和非合金冷型焊接結構型材.技術提交要求 |
Cold formed welded structural sections of non-alloy and fine grain steels - Technical delivery requirements |
| BS EN 10219-2-1997 |
精粒結構鋼和非合金冷型焊接結構型材.公差,尺寸和部分特性 |
Cold formed welded structural sections of non-alloy and fine grain steels - Tolerances, dimensions and sectional properties |
| BS EN 1022-1997 |
居室家具.坐椅穩定性的測試 |
Domestic furniture - Seating - Determination of stability |
| BS EN 1022-2005 |
居室家具.座椅.穩定性測定 |
|
| BS EN 10220-2002 |
無縫和焊接鋼管.尺寸和每單位長度的質量 |
Seamless and welded steel tubes - Dimensions and masses per unit length |
| BS EN 10221-1996 |
熱軋圓棒材和線材的表面質量的分類.交貨技術條件 |
Specification for surface quality classes for hot-rolled bars and rods - Technical delivery conditions |
| BS EN 10222-1-1998 |
壓力容器用鋼鍛件.敞口鑄模鍛件的一般要求 |
Steel forgings for pressure purposes - General requirements for open die forgings |
| BS EN 10222-2-2000 |
壓力容器用鋼鍛件.具有特殊提高溫度特性的鐵素體鋼和馬口鐵鋼 |
Steel forgings for pressure purposes - Ferritic and martensitic steels with specified elevated temperature properties |
| BS EN 10222-3-1999 |
壓力容器用鋼鍛件.具有特定低溫特性的鎳鋼 |
Steel forgings for pressure purposes - Nickel steels with specified low-temperature properties |
| BS EN 10222-4-1999 |
壓力容器用鋼鍛件.具有高驗收強度的可焊精粒鋼 |
Steel forgings for pressure purposes - Weldable fine-grain steels with high proof strength |
| BS EN 10222-5-2000 |
壓力容器用鋼鍛件.馬口鐵鋼,奧氏體鋼,奧氏體-鐵素體不銹鋼 |
(Steel forgings for pressure purposes - Martensitic, austenitic and austenitic-ferritic stainless steels) |
| BS EN 10223-1-1998 |
欄柵用鋼線和金屬線制品.鋅和鋅合金包覆的刺鋼絲線 |
Steel wire and wire products for fences - Zinc and zinc alloy coated steel barbed wire |
| BS EN 10223-2-1998 |
欄柵用鋼線和金屬線制品.農業,絕緣和欄柵用六角型鋼絲網 |
Steel wire and wire products for fences - Hexagonal steel wire netting for agricultural, insulation and fencing purposes |
| BS EN 10223-3-1998 |
欄柵用鋼線和金屬線制品.工程用六角型鋼絲網 |
Steel wire and wire products for fences - Hexagonal steel wire netting for engineering purposes |
| BS EN 10223-4-1998 |
柵欄用鋼絲和鋼絲制品.鋼絲焊接網式柵欄 |
Steel wire and wire products for fences - Steel wire welded mesh fencing |
| BS EN 10223-5-1998 |
柵欄用鋼絲和鋼絲制品.鋼絲編織絞接和打結網式柵欄 |
Steel wire and wire products for fences - Steel wire woven hinged joint and knotted mesh fencing |
| BS EN 10223-6-1998 |
柵欄用鋼線和線制品.鋼線鏈柵欄的測定 |
Steel wire and wire products for fences - Steel wire chain link fencing |
| BS EN 10223-7-2002 |
欄柵用鋼絲和金屬絲制品.欄柵用焊接鋼絲鋼條 |
Steel wire and wire products for fences - Steel wire welded panels - For fencing |
| BS EN 10224-2002 |
包括生活用水在內的水成液的輸送用非合金鋼管和配件.交貨技術條件 |
(Non-alloy steel tubes and fittings for the conveyance of aqueous liquids including water for human consumption - Technical delivery conditions) |
| BS EN 10225-2001 |
固定近海結構的可焊接結構鋼.技術提交條件 |
(Weldable structural steels for fixed offshore structures - Technical delivery conditions) |
| BS EN 10226-1-2004 |
螺紋上有壓力密封接縫的管螺紋.錐形外螺紋和平行內螺紋.尺寸、公差及名稱與符號 |
|
| BS EN 10226-1-2004 |
螺紋上有壓力密封接縫的管螺紋.錐形外螺紋和平行內螺紋.尺寸、公差及名稱與符號 |
|
| BS EN 10228-1-1999 |
鋼鍛件的無損檢驗.磁粉檢驗 |
(Non-destructive testing of steel forgings - Magnetic particle inspection) |
| BS EN 10228-2-1998 |
鋼鍛件的無損檢驗.滲透檢驗 |
(Non-destructive testing of steel forgings - Penetrant testing) |
| BS EN 10228-3-1998 |
鋼鍛件的無損檢驗.鐵素體或馬氏體鋼鍛件的超聲檢驗 |
(Non-destructive testing of steel forgings - Ultrasonic testing of ferritic or martensitic steel forgings) |
| BS EN 10228-4-1999 |
鋼鍛件的無損檢驗.奧氏體和奧氏體-鐵素體不銹鋼鍛件的超聲檢驗 |
(Non-destructive testing of steel forgings - Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings) |
| BS EN 10229-1998 |
鋼產品耐氫誘發斷裂(HIC)的評估 |
(Evaluation of resistance of steel products to hydrogen induced cracking (HIC)) |
| BS EN 1023-1-1997 |
辦公家具.遮板.尺寸 |
(Office furniture - Screens - Dimensions) |
| BS EN 1023-2-2000 |
辦公家具.遮板.機械安全要求 |
(Office furniture - Screens - Mechanical safety requirements) |
| BS EN 1023-3-2000 |
辦公家具.遮板.試驗方法 |
(Office furniture - Screens - Test methods) |
| BS EN 10230-1-2000 |
鋼圓鐵釘.一般應用的松動釘 |
(Steel wire nails - Loose nails for general applications) |
| BS EN 10232-1994 |
金屬材料.整截面管材彎曲試驗 |
(Metallic materials - Tube (in full section) - Bend test) |
| BS EN 10233-1994 |
金屬材料.管材.壓扁試驗 |
(Metallic materials - Tube - Flattening test) |
| BS EN 10234-1994 |
金屬材料.管材.管流延伸試驗 |
Metallic materials - Tube - Drift expanding test |
| BS EN 10235-1994 |
金屬材料.管材.突邊試驗 |
(Metallic materials - Tube - Flanging test) |
| BS EN 10236-1994 |
金屬材料.管材.環形管擴管試驗 |
(Metallic materials - Tube - Ring expanding test) |
| BS EN 10237-1994 |
金屬材料.管材.環形管拉伸試驗 |
(Metallic materials - Tube - Ring tensile test) |
| BS EN 10238-1997 |
自動噴砂清理和自動涂底漆結構鋼制品 |
(Automatically blast cleaned and automatically primed structural steel products) |
| BS EN 1024-1997 |
間斷敷設用粘土制屋面瓦.幾何性能測定 |
(Clay roofing tiles for discontinuous laying - Determination of geometric characteristics) |
| BS EN 10240-1998 |
鋼管內或外保護覆層.用于自動車間的熱浸電動覆膜規范 |
(Internal and/or external protective coatings for steel tubes - Specification for hot dip galvanized coatings applied in automatic plants) |
| BS EN 10241-2000 |
螺紋鋼管配件 |
(Steel threaded pipe fittings) |
| BS EN 10242-1995 |
可鍛鑄鐵的加螺紋管道配件 |
(Threaded pipe fittings in malleable cast iron) |
| BS EN 10243-1-1999 |
鋼模鍛.公差和尺寸.落錘或垂直壓力鍛造 |
(Steel die forgings - Tolerances on dimensions - Drop and vertical press forgings) |
| BS EN 10243-2-1999 |
鋼模鍛.公差和尺寸.水平鍛壓機器上的鐓鍛壓 |
(Steel die forgings - Tolerances on dimensions - Upset forgings made on horizontal forging machines) |
| BS EN 10244-1-2001 |
鋼線和線產品.鋼線上的非有色金屬涂層.一般原理 |
(Steel wire and wire products - Non-ferrous metallic coatings on steel wire - General principles) |
| BS EN 10244-2-2001 |
鋼線和線產品.鋼線上的非有色金屬涂層.鋅和鋅合金涂層 |
Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Zinc or zinc alloy coatings |
| BS EN 10244-3-2001 |
鋼線和線產品.鋼線上的非有色金屬涂層.鋁涂層 |
(Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Aluminium coatings) |
| BS EN 10244-4-2001 |
鋼線和線產品.鋼線上的非有色金屬涂層.錫涂層 |
(Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Tin coatings) |
| BS EN 10244-5-2001 |
鋼線和線產品.鋼線上的非有色金屬涂層.鎳涂層 |
(Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Nickel coatings) |
| BS EN 10244-6-2001 |
鋼線和線產品.鋼線上的非有色金屬涂層.銅,青銅或黃銅涂層 |
(Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Copper, bronze or brass coatings) |
| BS EN 10245-1-2001 |
鋼線和線產品.鋼線上的有機涂層.一般規則 |
(Steel wire and wire products - Organic coatings on steel wire - General rules) |
| BS EN 10245-2-2001 |
鋼線和線產品.鋼線上的有機涂層.PVC精制線 |
(Steel wire and wire products - Organic coatings on steel wire - PVC finished wire) |
| BS EN 10245-3-2001 |
鋼線和線產品.鋼線上的有機涂層.PE涂層線 |
(Steel wire and wire products - Organic coatings on steel wire - PE coated wire) |
| BS EN 10245-4-2003 |
鋼絲和鋼絲產品.鋼絲上的有機涂層.聚酯涂層絲 |
(Steel wire and wire products - Organic coatings on steel wire - Polyester coated wire) |
| BS EN 10246-1-1996 |
鋼管的無損檢驗.證明液壓系統密封性用無縫和焊接鐵磁鋼管(埋弧焊除外)的自動電磁檢驗 |
(Non-destructive testing of steel tubes - Automatic electromagnetic testing of seamless and welded (except submerged arc welded) ferromagnetic steel tubes for verification of hydraulic leak-tightness) |
| BS EN 10246-10-2000 |
鋼管的無損檢驗.缺陷探測用自動熔融電弧焊接鋼管焊縫的放射線檢驗 |
(Non-destructive testing of steel tubes - Radiographic testing of the weld seam of automatic fusion arc welded steel tubes for the detection of imperfections) |
| BS EN 10246-11-2000 |
鋼管的無損檢測.表面缺陷檢測用無縫和焊接鋼管的液體滲透試驗 |
(Non-destructive testing of steel tubes - Liquid penetrant testing of seamless and welded steel tubes for the detection of surface imperfections) |
| BS EN 10246-12-2000 |
鋼管的無損檢測.表面缺陷檢測用無縫和焊接鋼管的磁粉檢測 |
(Non-destructive testing of steel tubes - Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections) |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com