標準號 |
中文名稱 |
英文名稱 |
| BS EN 196-21-1992 |
水泥的試驗方法.第21部分:水泥中氯化物、二氧化碳和堿含量的測定 |
(Methods of testing cement - Determination of the chloride, carbon dioxide and alkali content of cement) |
| BS EN 196-3-1995 |
測試水泥的方法.凝固時間和安定性的測定 |
(Methods of testing cement - Determination of setting time and soundness) |
| BS EN 196-5-1995 |
測試水泥的方法.火山灰水泥的凝硬試驗 |
(Methods of testing cement - Pozzolanicity test for pozzolanic cements) |
| BS EN 196-6-1992 |
水泥的試驗方法.細度的測定 |
(Methods of testing cement - Determination of fineness) |
| BS EN 196-7-1992 |
水泥的試驗方法.試樣的取樣和制備方法 |
(Methods of testing cement - Methods of taking and preparing samples of cement) |
| BS EN 196-8-2004 |
測試水泥的方法.水合熱.溶解法 |
|
| BS EN 196-9-2004 |
測試水泥的方法.水合熱.半絕熱法 |
|
| BS EN 196000-1993 |
電子器件質量評定協調體系.總規范.機電式開關 |
(Harmonized system of quality assessment for electronic components - Generic specification - Electromechanical switches) |
| BS EN 196103-2000 |
空白詳細規范:旋轉式開關.評估等級Y |
(Blank detail specification: Rotary switches - Assessment level Y) |
| BS EN 1963-1998 |
織物地板鋪面.使用Lisson踏輪機的試驗 |
(Textile floor coverings - Tests using the Lisson Tretrad machine) |
| BS EN 1964-1-2000 |
便攜氣體鋼瓶.水容量由0,5升到150升(包括150升)的可再充氣的便攜無縫鋼制氣體瓶的設計和結構規范.閥門壓力 |
() |
| BS EN 1964-2-2001 |
可移動儲氣罐.水容量為0.5升至150升的可充氣可移動的無縫鋼儲氣罐的設計和結構規范.RDOWNm值為大于等于1100 |
() |
| BS EN 1964-3-2000 |
便攜氣體鋼瓶.水容量由0,5升到150升(包括150升)的可再充氣的便攜無縫不銹鋼制氣體瓶的設計和結構規范.閥門 |
() |
| BS EN 196403-2000 |
電子器件質量評定協調體系.空白詳細規范.Y級評定 |
(Harmonized systems of quality assessment for electronic components - Blank detail specification: push button switches - Assessment level Y) |
| BS EN 1965-1-2001 |
結構膠粘劑.腐蝕性.對銅襯底腐蝕性的測定和分類 |
(Structural adhesives - Corrosion - Determination and classification of corrosion to a copper substrate) |
| BS EN 1965-2-2001 |
結構膠粘劑.腐蝕性.對黃銅襯底腐蝕性的測定和分類 |
(Structural adhesives - Corrosion - Determination and classification of corrosion to a brass substrate) |
| BS EN 196500-1993 |
電子器件質量評定協調體系.分規范.包括空白詳細規范EN 196501的薄膜開關 |
(Harmonized system of quality assessment for electronic components - Sectional specification - Membrane switches including blank detail specification EN 196501) |
| BS EN 1966-2002 |
建筑用粘接劑.用三點彎曲法測量粘接劑表面的表示特性 |
(Structural adhesives - Characterisation of a surface by measuring adhesion by means of the three point bending method) |
| BS EN 1967-2002 |
結構膠粘劑.用與導向托輥法有關的濕剝離試驗評價鋁表面處理技術的有效性 |
(Structural adhesives - Evaluation of the effectiveness of surface treatment techniques for aluminium using a wet peel test in association with the floating roller method) |
| BS EN 1968-2002 |
可運輸儲氣瓶.無縫鋼儲氣瓶的周期性檢驗和測試 |
(Transportable gas cylinders - Periodic inspection and testing of seamless steel gas cylinders) |
| BS EN 1969-2000 |
運動場表面.合成運動場表面厚度的測定 |
(Surfaces for sports areas - Determination of thickness of synthetic sports surfaces) |
| BS EN 197-1-2000 |
水泥.通用水泥組分、規范和合格標準 |
(Cement - Composition, specifications and conformity criteria for common cements) |
| BS EN 197-2-2000 |
水泥.合格評定 |
(Cement - Conformity evaluation) |
| BS EN 197-4-2004 |
水泥.早硬低強度高爐水泥的組分、規范和合格標準 |
|
| BS EN 1970-2000 |
殘疾人用可調整的床.要求和試驗方法 |
(Adjustable beds for disabled persons - Requirements and test methods) |
| BS EN 1971-1999 |
銅和銅合金.管的渦流試驗 |
(Copper and copper alloys - Eddy current test for tubes) |
| BS EN 1972-1997 |
潛水輔助設備.通氣管.安全設備和試驗方法 |
(Diving accessories - Snorkels - Safety requirements and test methods) |
| BS EN 1974-1998 |
食品加工機械.切片機的安全和衛生要求 |
(Food processing machinery - Slicing machines - Safety and hygiene requirements) |
| BS EN 1975-2000 |
便攜氣體鋼瓶.容量由0,5升到150升(包括150升)的由無縫鋁和鋁合金制的氣體瓶的設計和結構規范. |
(Transportable gas cylinders - Specification for the design and construction of refillable transportable seamless aluminium and aluminium alloy gas cylinders of capacity from 0,5 litre up to 150 ) |
| BS EN 1976-1998 |
銅及銅合金.未最后定形的銅鑄件產品 |
(Copper and copper alloys - Cast unwrought copper products) |
| BS EN 1977-1998 |
銅及銅合金.銅拉制手柄(繞線桿材) |
(Copper and copper alloys - Copper drawing stock (wire rod)) |
| BS EN 1978-1998 |
銅及銅合金.銅陰極 |
(Copper and copper alloys - Copper cathodes) |
| BS EN 1979-1999 |
塑料管道和管道系統.熱塑螺旋型結構壁的管道.接縫拉伸強度的測定 |
(Plastics piping and ducting systems - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam) |
| BS EN 1981-2003 |
銅及銅合金.母合金 |
(Copper and copper alloys - Master alloys) |
| BS EN 1982-1999 |
銅和銅合金.鑄錠和鑄件 |
(Copper and copper alloys - Ingots and castings) |
| BS EN 1984-2000 |
工業閥門.鋼插板閥門 |
(Industrial valves - Steel gate valves) |
| BS EN 1985-1999 |
助步器.一般要求和試驗方法 |
(Walking aids - General requirements and test methods) |
| BS EN 1986-1-1997 |
電動道路車輛.能量特性測定.純電動車 |
(Electrically propelled road vehicles - Measurement of energy performances - Pure electric vehicles) |
| BS EN 1986-2-2001 |
電動道路車輛.能量特性測定.熱電復式動力車 |
(Electrically propelled road vehicles - Measurement of energy performances - Thermal electric hybrid vehicles) |
| BS EN 1987-1-1997 |
電車.安全的特殊要求.能量?jī)?chǔ)存板 |
(Electrically propelled road vehicles - Specific requirements for safety - On board energy storage) |
| BS EN 1987-2-1997 |
電車.安全的特殊要求.功能安全措施和失效防護 |
(Electrically propelled road vehicles - Specific requirements for safety - Functional safety means and protection against failures) |
| BS EN 1987-3-1998 |
電車.安全的特殊要求.防止乘客被電傷害的保護措施 |
(Electrically propelled road vehicles - Specific requirements for safety - Protection of users against electrical hazards) |
| BS EN 1988-1-1998 |
食品.亞硫酸鹽的測定.最佳Monier-Williams法 |
(Foodstuffs - Determination of sulfite - Optimized Monier-Williams method) |
| BS EN 1988-2-1998 |
食品.亞硫酸鹽的測定.酶催法 |
(Foodstuffs - Determination of sulfite - Enzymatic method) |
| BS EN 1989-2000 |
熱塑管道系統.地埋無壓力排水設施用連接件.通過估計密封壓力對帶熱塑彈力計密封連接件長期密封性能的試驗方 |
(Thermoplastics piping systems - Joints for buried non-pressure sewerage applications - Test method for long-term sealing performance of joints with thermoplastic elastomer (TPE) seals by estimating th) |
| BS EN 1990-2002 |
歐洲法規.建筑設計基礎 |
(Eurocode - Basis of structural design) |
| BS EN 1991-1-1-2002 |
歐洲法規 1.機構作用.一般作用.建筑物的密度、自重和強制負荷 |
(Eurocode 1. Actions on structures - General actions - Densities, self-weight, imposed loads for buildings) |
| BS EN 1991-1-2-2002 |
歐洲法規 1.對建筑物的作用.一般作用.對建筑物防火的作用 |
(Eurocode 1. Actions on structures - General actions - Actions on structures exposed to fire) |
| BS EN 1991-1-3-2003 |
歐洲法規1:對結構的作用.一般作用.雪荷載 |
(Eurocode 1. Actions on structures - General actions - Snow loads) |
| BS EN 1991-1-5-2004 |
歐洲法規 1.對建筑物的作用.一般作用.熱作用 |
|
| BS EN 1991-1-5-2004 |
歐洲法規 1.對建筑物的作用.一般作用.熱作用 |
|
| BS EN 1991-2-2003 |
歐洲法規 1.對建筑物的作用.橋上的交通荷載 |
(Eurocode 1. Actions on structures - Traffic loads on bridges) |
| BS EN 1992-1-1-2004 |
歐洲法規2.混凝土結構設計.一般規則和建筑規則 |
|
| BS EN 1992-1-2-2005 |
歐洲法規2.混凝土結構設計.一般規則.結構防火設計 |
|
| BS EN 1994-1-1-2005 |
歐洲法規4.復合鋼和混凝土結構的設計.建筑物用通用規則和規則 |
|
| BS EN 1995-1-1-2004 |
歐洲法規5.木結構的設計.總則.通用規則和建筑規則 |
|
| BS EN 1997-1-2004 |
歐洲法規7.土木技術設計.總則 |
|
| BS EN 1998-1-2005 |
歐洲法規8.抗震結構設計.建筑物用一般規則、地震作用和規則 |
|
| BS EN 2-1992 |
火災的分類 |
(Classification of fires) |
| BS EN 20-1-1992 |
木材防腐劑.對竹粉蠹蟲(lycuts)預防作用的測定.利用表面處理法(實驗室法) |
(Wood preservatives - Determination of the protective effectiveness against Lyctus brunneus (Stephens) - Application by surface treatment (laboratory method)) |
| BS EN 20-2-1993 |
木材防腐劑.對竹粉蠹防護效果的測定.利用浸漬法(實驗室法) |
(Wood preservatives - Determination of the protective effectiveness against Lyctus brunneus (Stephens) - Application by impregnation (laboratory method)) |
| BS EN 200-1992 |
衛生用水龍頭.PN10型單一和混合水龍頭(公稱尺寸1/2)通用技術規范.最小流動壓力0.05MPa(0.5bar) |
(Sanitary tapware - General technical specifications for single taps and mixer taps (nominal size 1/2) PN 10 - Minimum flow pressure of 0.05 MPa (0.5 bar)) |
| BS EN 2000-1992 |
質量保證.EN航空航天產品.制造廠質量體系的鑒定 |
(Quality assurance - EN aerospace products - Approval of the quality system of manufacturers) |
| BS EN 2004-1-1993 |
鋁和鋁合金產品試驗方法.第1部分:鍛鋁合金電導率的測定 |
(Test methods for aluminium and aluminium alloy products - Determination of electrical conductivity of wrought aluminium alloys) |
| BS EN 2004-1-1993 |
鋁和鋁合金產品試驗方法.第1部分:鍛鋁合金電導率的測定 |
|
| BS EN 2004-5-1993 |
鋁和鋁合金產品試驗方法.第5部分:包層半成品的包層厚度和銅擴散的測定 |
(Test methods for aluminium and aluminium alloy products - Determination of cladding thickness and copper diffusion of clad semi-finished products) |
| BS EN 2004-5-1993 |
鋁和鋁合金產品試驗方法.第5部分:包層半成品的包層厚度和銅擴散的測定 |
|
| BS EN 2009-1992 |
軸承.飛機機架的滾壓.直徑為8和9系列的剛性、單排鋼球軸承、尺寸和載荷 |
(Bearings - Airframe rolling rigid, single row ball bearings in steel diameter series 8 and 9. Dimensions and loads) |
| BS EN 201-1997 |
橡膠和塑料機械.注模機械.安全要求 |
(Rubber and plastics machines - Injection moulding machines - Safety requirements) |
| BS EN 20105-A02-1995 |
紡織品.色牢度試驗.第A02部分:彩色變化評定灰度等級 |
(Textiles - Tests for colour fastness - Grey scale for assessing change in colour) |
| BS EN 20105-A03-1995 |
紡織品.色牢度試驗.第A03部分:沾污評定灰度等級 |
(Textiles - Tests for colour fastness - Grey scale for assessing staining) |
| BS EN 20105-C01-1993 |
紡織品.色牢度試驗.耐洗滌色牢度:試驗1 |
(Textiles - Tests for colour fastness - Colour fastness to washing: Test 1) |
| BS EN 20105-C03-1993 |
紡織品.色牢度試驗.耐洗滌色牢度:試驗3 |
(Textiles - Tests for colour fastness - Colour fastness to washing: Test 3) |
| BS EN 20105-C04-1993 |
紡織品.色牢度試驗.第C04部分:耐洗滌色牢度:試驗4 |
(Textiles - Tests for colour fastness - Colour fastness to washing: Test 4) |
| BS EN 20105-C05-1993 |
紡織品.色牢度試驗.第C05部分:耐洗滌色牢度:試驗5 |
(Textiles - Tests for colour fastness - Colour fastness to washing: Test 5) |
| BS EN 20105-N01-1995 |
紡織品的色牢度試驗.第N01部分:耐褪色的色牢度.次氯酸鹽試驗方法 |
(Textiles - Tests for colour fastness - Colour fastness to bleaching: hypochlorite) |
| BS EN 2011-1989 |
直徑為8和9系列防腐鋼單列滾珠軸承管架滾動剛性規范.尺寸和負載 |
(Specification for bearings - airframe rolling rigid single row ball bearings in corrosion resisting steel diameter series 8 and 9. Dimensions and loads) |
| BS EN 2012-1989 |
直徑為0和2系列鋼單列滾珠軸承管架滾動剛性規范.尺寸和負載 |
(Specification for bearings - airframe rolling rigid, single row ball bearings in steel diameter series 0 and 2. Dimensions and loads) |
| BS EN 20139-1992 |
紡織品.調節和檢驗用的標準大氣 |
(Textiles - Standard atmospheres for conditioning and testing) |
| BS EN 2014-1989 |
軸承規范.直徑為0和2系列的防腐鋼制飛機用軋制剛性單列滾珠軸承.尺寸和荷載 |
(Specification for bearings - airframe rolling rigid single row ball bearings in corrosion resisting steel diameter series 0 and 2. Dimensions and loads) |
| BS EN 20140-10-1992 |
聲學.建筑物和構件隔音的測量.第10部分:小型建筑構件隔音的實驗室測量 |
(Acoustics - Measurement of sound insulation in buildings and of building elements - Laboratory measurement of airborne sound insulation of small building elements) |
| BS EN 20140-2-1993 |
聲學.建筑物和建筑構件的隔音測量.第2部分:精確數據的確定.驗證和應用 |
(Determination, verification and application of precision data) |
| BS EN 20140-9-1987 |
聲學.建筑物和建筑構件的隔音測量.懸吊式天花板上有壓力通風的室對室氣載音響隔離的實驗室測量 |
(Acoustics - Measurement of sound insulation in buildings and of building elements - Laboratory measurement of room-to-room airborne sound insulation of a suspended ceiling with a plenum above it) |
| BS EN 2015-1989 |
直徑為2系列的雙列自調整鋼滾珠軸承管架滾動剛性規范.尺寸和負載 |
(Specification for bearings - airframe rolling double row, self aligning ball bearings in steel diameter series 2. Dimensions and loads) |
| BS EN 2017-1989 |
軸承規范.直徑為2系列的防腐鋼制飛機用軋制雙列自調整滾珠軸承.尺寸和荷載 |
(Specification for bearings - airframe rolling double row self aligning ball bearings in corrosion resisting steel diameter series 2. Dimensions and loads) |
| BS EN 2018-1989 |
直徑為3和4系列單列自調整鋼滾珠軸承管架滾動剛性規范.尺寸和負載 |
(Specification for bearings - airframe rolling single row, self aligning roller bearings in steel diameter series 3 and 4. Dimensions and loads) |
| BS EN 20187-1993 |
紙、紙板和紙漿.樣品調理 |
(Paper, board and pulps - Standard atmosphere for conditioning and testing and procedure for monitoring the atmosphere and conditioning of samples) |
| BS EN 2020-1989 |
直徑為3和4系列單列自調整防腐鋼滾珠軸承管架滾動剛性規范.尺寸和負載 |
(Specification for bearings - airframe rolling single row self aligning roller bearings in corrosion resisting steel diameter series 3 and 4. Dimensions and loads) |
| BS EN 2022-1990 |
具有自潤滑軸瓦的防腐鋼球面軸承規范.輕型系列.尺寸和負載 |
(Specification for bearings, spherical plain in corrosion resisting steel with self-lubricating liner - Light series - Dimensions and loads) |
| BS EN 20225-1992 |
緊固件.螺栓、螺柱和螺母.圖形符號和尺寸 |
(Fasteners - Bolts, screws, studs and nuts - Symbols and designations of dimensions) |
| BS EN 2023-1989 |
具有自潤滑軸瓦的防腐鋼球面軸承規范.標準系列.尺寸和負載 |
(Specification for bearings - spherical plain in corrosion resisting steel with self-lubricating liner - Normal series - Dimensions and loads) |
| BS EN 20273-1992 |
緊固件.螺栓和螺釘自由尺寸孔 |
(Fasteners - Clearance holes for bolts and screws) |
| BS EN 20286-1-1990 |
ISO極限和配合體系.公差,偏差和配合的基礎 |
(ISO system of limits and fits - ISO system of limits and fits - Bases of tolerances, deviations and fits) |
| BS EN 20286-2-1990 |
ISO極限和配合體系.孔和軸標準公差等級和極限偏差表 |
(ISO system of limits and fits - ISO system of limits and fits - Tables of standard tolerance grades and limit deviations for holes and shafts) |
| BS EN 20287-1986 |
紙和紙板.水份含量的測定.烘干法 |
(Paper and board - Determination of moisture content - Oven-drying method) |
| BS EN 203-1-1993 |
煤氣加熱供膳設備規范.安全要求 |
(Specification for gas heated catering equipment - Safety requirements) |
| BS EN 203-1-2005 |
煤氣加熱供膳設備.一般安全規則 |
|
| BS EN 203-2-1995 |
煤氣加熱供膳設備規范.能源的合理使用 |
(Specification for gas heated catering equipment - Rational use of energy) |
| BS EN 2032-1-2002 |
金屬材料.常規命名 |
(Metallic materials - Conventional designation) |
| BS EN 2032-2-1994 |
金屬材料.運輸條件下金屬材料狀況標記 |
(Metallic materials - Coding of metallurgical condition in delivery condition) |
| BS EN 20340-1993 |
輸送帶的阻燃規范和試驗方法 |
(Conveyor belts - Flame retardation - Specifications and test method) |
| BS EN 204-2001 |
非結構熱塑性木材膠粘劑分類 |
(Classification of thermoplastic wood adhesives for non-structural applications) |
| BS EN 2044-2001 |
航空航天系列.鋁及鋁合金拉制圓棒.公差等級h11.直徑4mm |
(Aerospace series - Round bars, drawn, in aluminium and aluminium alloys - Tolerance class h 11 - Diameter 4 mm) |
| BS EN 2045-2001 |
航空航天系列.鋁及鋁合金拉制方棒.公差等級h11.厚度6mm |
(Aerospace series - Square bars, drawn, in aluminium and aluminium alloys - Tolerance class h 11 - Thickness 6 mm) |
| BS EN 2046-2001 |
鋁及鋁合金拉制六角形棒材.公差等級h11.對邊寬度7mm |
(Hexagonal bars, drawn, in aluminium and aluminium alloys - Tolerance class h 11 - Width across flats 7 mm) |
| BS EN 2047-2001 |
航空航天系列.帶邊L型鋁及鋁合金擠壓件.尺寸 |
(Aerospace series - Beaded L-section extruded, in aluminium and aluminium alloys - Dimensions) |
| BS EN 2048-2001 |
航空航天系列.鋁合金中的擠壓L型材.尺寸 |
(Aerospace series - Extruded L-section in aluminium alloys - Dimensions) |
| BS EN 2049-2001 |
航空航天系列.U型鋁及鋁合金擠壓件.尺寸 |
(Aerospace series - Extruded channel section, in aluminium alloys - Dimensions) |
| BS EN 205-2003 |
膠粘劑.非結構用木材粘結劑試驗方法.搭接接頭拉伸剪切強度的測量 |
(Adhesives - Wood adhesives for non-structural applications - Determination of tensile shear strength of lap joints) |
| BS EN 2050-2001 |
航空航天系列.T型鋁及鋁合金擠壓件.尺寸 |
(Aerospace series - Extruded T-section, in aluminium alloys - Dimensions) |
| BS EN 20534-1989 |
紙和紙板表觀頁密度或表觀塊密度及厚度的測定方法 |
(Method for determination of thickness and apparent bulk density or apparent sheet density of paper and board) |
| BS EN 20535-1991 |
紙和紙板.水吸收性測定.Cobb法 |
(Paper and board - Determination of water absorptiveness - Cobb method) |
| BS EN 20594-1-1987 |
注射器、針頭和某些其它醫用設備的有6%錐度的錐形配件.一般要求 |
(Conical fittings with a 6% (Luer) taper for syringes, needles and certain other medical equipment - General requirements) |
| BS EN 206-1-2001 |
混凝土.規范、性能、產品及合格 |
(Concrete - Specification, performance, production and conformity) |
| BS EN 2063-1992 |
飛行器骨架滾動軸承.技術規范 |
(Airframe rolling bearings - Technical specification) |
| BS EN 20638-1980 |
紙漿中干物質含量測定的方法 |
(Method for determination of dry-matter content of pulps) |
| BS EN 2064-1992 |
具有自潤滑軸套的球面防腐鋼軸承.技術規范 |
(Bearings, spherical plain in corrosion resisting steel with self lubricating liner - Technical specification) |
| BS EN 2066-2002 |
航空航天系列.鋁合金擠制型材.一般公差 |
(Aerospace series - Extruded section in aluminium alloys - General tolerances) |
| BS EN 2067-1996 |
用于桿端的自測軸承承重.技術規范 |
(Rod ends with self-aligning ball bearings - Technical specification) |
| BS EN 2068-1996 |
用于桿端的自潤滑自測承重.技術規范 |
(Rod ends with self-lubricating self-aligning bearings - Technical specification) |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com