標準號 |
中文名稱 |
英文名稱 |
| BS ISO 7772-3-1996 |
通過對織物的影響來評價工業洗衣設備.第3部分:家用織物熨平機 |
Assessment of industrial laundry machinery by its effect on textiles - Flatwork-ironing machines |
| BS ISO 7772-4-1996 |
通過對織物的影響來評價工業洗衣設備.第4部分:分批干燥機 |
Assessment of industrial laundry machinery by its effect on textiles - Batch-drying tumblers |
| BS ISO 778-2001 |
紙,紙漿和紙板.銅的測定 |
Paper, board and pulp - Determination of copper |
| BS ISO 7780-1998 |
橡膠和橡膠膠乳.錳含量的測定.高碘酸鈉光度計法 |
Rubber and rubber latices - Determination of manganese content - Sodium periodate photometric methods |
| BS ISO 7781-2002 |
丁苯生膠.皂類和有機酸含量的測定 |
Styrene-butadiene rubber, raw - Determination of soap and organic acid content |
| BS ISO 7789-1998 |
液壓動力-插裝式閥二,三和四口螺紋.空腔 |
Hydraulic fluid power - Two-, three- and four-port screw-in cartridge valves - Cavities |
| BS ISO 779-2001 |
紙,紙漿和紙板.鐵的測定 |
Paper, board and pulp - Determination of iron |
| BS ISO 7790-1998 |
液壓傳動.規格為03和05型的四油口標準設計疊閥和四油口定向控制閥.緊固尺寸 |
Hydraulic fluid power - Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05 - Clamping dimensions |
| BS ISO 7792-1-1998 |
塑料.熱塑聚酯(TP)模塑和擠壓材料.命名體制和基本規范 |
Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Designation system and basis for specifications |
| BS ISO 7792-2-1998 |
塑料.熱塑聚酯(TP)模塑和擠壓材料.試樣制備和性能測定 |
Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Preparation of test specimens and determination of properties |
| BS ISO 78-2-1999 |
化學.標準的布局.化學分析方法 |
Chemistry - Layout for standards - Methods of chemical analysis |
| BS ISO 7800-2003 |
金屬材料.線材.單向扭轉試驗 |
(Metallic materials - Wire - Simple torsion test) |
| BS ISO 7858-1-1998 |
閉合管路中水流量測量.飲用冷水用組合儀表.規范 |
Measurement of water flow in closed conduits - Combination meters for cold potable water - Specifications |
| BS ISO 7858-2-2001 |
閉合管路中水流量測量.飲用冷水用組合儀表.安裝要求 |
Measurement of water flow in closed conduits - Combination meters for cold potable water - Installation requirements |
| BS ISO 7859-2000 |
機動腳踏兩用車.燃料消耗量的測量 |
Mopeds - Fuel consumption measurements |
| BS ISO 7862-2004 |
道路車輛.通過模擬前面碰撞評價約束系統的滑板碰撞試驗規程 |
|
| BS ISO 7867-1-2005 |
農業拖拉機和機械用輪胎和輪輞(米制系列).輪胎名稱、尺寸、標志和輪胎/輪輞的配合 |
|
| BS ISO 7867-2-2005 |
農業拖拉機和機械用輪胎和輪輞(米制系列).使用條件及額定負載 |
|
| BS ISO 787-17-2002 |
顏料和體質顏料的試驗通用方法.白色顏料亮度比較 |
General methods of test for pigments and extenders - Comparison of lightening power of white pigments |
| BS ISO 7876-4-2005 |
燃油噴射裝置.詞匯.高壓管和末端接頭 |
|
| BS ISO 7879-1998 |
柴油發動機.托架安裝直列柱塞燃料泵.安裝尺寸 |
Diesel engines - Cradle mounted in-line fuel injection pumps - Mounting dimensions |
| BS ISO 7889-2003 |
酸奶.特性微生物的計數.37℃時的菌落計數法 |
Yogurt - Enumeration of characteristic microorganisms - Colony-count technique at 37 鳦 |
| BS ISO 7914-2002 |
林業機械.便攜式鏈鋸.最小把手間隙和尺寸 |
Forestry machinery - Portable chain-saws - Minimum handle clearance and sizes |
| BS ISO 7918-1996 |
林業機械.手提式刷鋸和草地平整器.割炬附件的護板尺寸 |
Forestry machinery - Portable brush cutters and grass trimmers - Cutting attachment guard dimensions |
| BS ISO 7919-1-1996 |
非往復式機械的機械振動.對旋轉軸的測量和評定規范.第1部分:一般導則 |
Mechanical vibration of non-reciprocating machines - Measurements on rotating shafts and evaluation criteria - General guidelines |
| BS ISO 7919-2-2002 |
非往復式機器的機械振動.旋轉軸的測量和評價標準.陸地安裝,功率超過50MW,正常運轉速度為1500r/min、1800r/min、3000r/min和3600r/min的汽輪發電機組 |
Mechanical vibration of non-reciprocating machines - Measurements on rotating shafts and evaluation criteria - Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1500 r/min, 1800 r/min, 3000 r/min and 3600 r/min |
| BS ISO 7919-3-1996 |
非往復式機械的機械振動.對旋轉軸的測量和評定規范.第3部分:耦合工業機械 |
Mechanical vibration of non-reciprocating machines - Measurements on rotating shafts and evaluation criteria - Coupled industrial machines |
| BS ISO 7919-4-1996 |
非往復式機械的機械振動.對旋轉軸的測量和評定規范.第4部分:燃氣輪機組 |
Mechanical vibration of non-reciprocating machines - Measurements on rotating shafts and evaluation criteria - Gas turbine sets |
| BS ISO 7919-5-1997 |
非往復式機械的機械振動.對旋轉軸的測量和評定規范.液壓動力制造和抽氣裝置用機械組 |
Mechanical vibration of non-reciprocating machines - Measurements on rotating shafts and evaluation criteria - Machine sets in hydraulic power generating and pumping plants |
| BS ISO 7967-5-2003 |
往復式內燃機.零件和系統的詞匯.冷卻系統 |
(Reciprocating internal combustion engines - Vocabulary of components and systems - Cooling systems) |
| BS ISO 7967-8-2005 |
往復式內燃機.零部件和系統詞匯.起動系統 |
|
| BS ISO 7970-2000 |
小麥.規范 |
Wheat (Triticum aestivum L.) - Specification |
| BS ISO 7971-1-2003 |
谷物.容積密度“百升質量“的測定.參照法 |
(Cereals - Determination of bulk density, called “mass per hectolitre“ - Reference method) |
| BS ISO 7981-1-2005 |
水質.測定多核芳香烴類(PAH).液液萃取后用帶熒光檢測的高效薄層色譜法測定六PAH |
|
| BS ISO 7981-2-2005 |
水質.測定多核芳香烴類(PAH).液液萃取后用帶熒光檢測的高效液相色譜法測定六PAH |
|
| BS ISO 799-2004 |
船舶和海上技術.領航員扶梯 |
|
| BS ISO 7992-1995 |
鐵礦石.負載條件下還原性能測定 |
Iron ores - Determination of reduction properties under load |
| BS ISO 8007-3-2005 |
鋁生產用碳素材料.單個材料的取樣方案和取樣.側壁塊 |
|
| BS ISO 8009-1-1997 |
可重復使用的橡膠避孕隔膜.第1部分:分類、抽樣和要求 |
Reusable rubber contraceptive diaphragms - Classification, sampling and requirements |
| BS ISO 8009-10-1997 |
可重復使用的橡膠避孕子宮帽.第10部分:儲存的推薦方法 |
Reusable rubber contraceptive diaphragms - Recommendations for storage |
| BS ISO 8009-2-1997 |
可重復使用的橡膠避孕子宮帽.第2部分:尺寸的測定 |
Reusable rubber contraceptive diaphragms - Determination of size |
| BS ISO 8009-3-1997 |
可重復使用的橡膠避孕子宮帽.第3部分:子宮帽圓頂厚度的測定 |
Reusable rubber contraceptive diaphragms - Determination of dome thickness |
| BS ISO 8009-4-1997 |
可重復使用的橡膠避孕子宮帽.第4部分:防可見陷缺 |
Reusable rubber contraceptive diaphragms - Freedom from visible defects |
| BS ISO 8009-5-1997 |
可重復使用的橡膠避孕子宮帽.第5部分:抗拉性能的測定 |
Reusable rubber contraceptive diaphragms - Determination of tensile properties |
| BS ISO 8009-6-1997 |
可重復使用的橡膠避孕子宮帽.第6部分:加速老化后的變質測定 |
Reusable rubber contraceptive diaphragms - Determination of deterioration after accelerated ageing |
| BS ISO 8009-7-1997 |
可重復使用的橡膠避孕子宮帽.第7部分:螺簧和扁簧子宮帽的抗壓縮性測定 |
Reusable rubber contraceptive diaphragms - Determination of compression resistance of coil spring and flat spring diaphragms |
| BS ISO 8009-8-1997 |
可重復使用的橡膠避孕子宮帽.第8部分:螺簧和扁簧子宮帽壓縮時的扭轉測定 |
Reusable rubber contraceptive diaphragms - Determination of twisting during compression of coil spring and flat spring diaphragms |
| BS ISO 8009-9-1997 |
可重復使用的橡膠避孕子宮帽.第9部分:包裝和標簽 |
Reusable rubber contraceptive diaphragms - Packaging and labelling |
| BS ISO 8015-2001 |
技術制圖.公差標注基本原則 |
Technical drawings - Fundamental tolerancing principle |
| BS ISO 8020-2002 |
壓制用工具.帶圓頭和直線或者縮小柄的沖頭 |
Tools for pressing - Punches with cylindrical head and straight or reduced shank |
| BS ISO 8038-2-2001 |
光學和光學儀器.顯微鏡目鏡和相關換鏡旋座的螺紋.螺紋型M25×0.75mm |
Optics and optical instruments - Screw threads for microscope objectives and related nosepieces - Screw thread type M25 x 0,75 mm |
| BS ISO 8040-2001 |
光學和光學儀器.顯微鏡.鏡筒導板和鏡筒槽的連接尺寸 |
Optics and optical instruments - Microscopes - Dimensions of tube slide and tube slot connections |
| BS ISO 80416-2-2001 |
設備上用的圖形符號的基本原則.箭頭的格式和使用 |
Basic principles for graphical symbols for use on equipment - Form and use of arrows |
| BS ISO 8051-1999 |
公稱直徑從M3-M10的長柄絲錐.帶凹槽的全尺寸絲錐 |
Long shank taps with nominal diameters from M3 to M10 - Full-diameter shank taps with recess |
| BS ISO 8058-1999 |
空中貨運.隔熱集裝箱.熱效率要求 |
Air cargo - Insulated containers - Thermal efficiency requirements |
| BS ISO 806-2004 |
主要用于鋁生產的氧化鋁.在300$ODC和1000$ODC時質量損失的測定 |
|
| BS ISO 8066-2-2001 |
自動空調器用橡膠和塑料軟管及軟管配件.規范.冷卻劑134a |
Rubber and plastics hoses and hose assemblies for automotive air conditioning - Specification - Refrigerant 134a |
| BS ISO 8082-1996 |
自走式林業機械.防傾翻結構.實驗室試驗和性能要求 |
Self-propelled machinery for forestry - Roll-over protective structures - Laboratory tests and performance requirements |
| BS ISO 8082-2003 |
自行式林業機械.滾翻防護裝置.實驗室試驗和性能要求 |
(Self-propelled machinery for forestry - Roll-over protective structures - Laboratory tests and performance requirements) |
| BS ISO 8084-2003 |
林業機械.操作人員保護結構.實驗室試驗和性能要求 |
(Machinery for forestry - Operator protective structures - Laboratory tests and performance requirements) |
| BS ISO 8085-1-2001 |
與供應氣體燃料的聚乙烯管一起使用的聚乙烯配件.米制系列.規范.通過加熱器具進行的套筒熔融用配件 |
Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels - Metric series - Specifications - Fittings for socket fusion using heated tools |
| BS ISO 8085-2-2001 |
與供應氣體燃料的聚乙烯管一起使用的聚乙烯配件.米制系列.規范.熔接用的、通過加熱器具進行的套筒熔融用的及與電熔融一起使用的配件 |
Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels - Metric series - Specifications - Spigot fittings for butt fusion, for socket fusion using heated tools and for use with eletrofusion fittings |
| BS ISO 8085-3-2001 |
與供應氣體燃料的聚乙烯管一起使用的聚乙烯配件.米制系列.規范.電熔融配件 |
Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels - Metric series - Specifications - Electrofusion fittings |
| BS ISO 8086-2004 |
乳品廠.衛生條件.檢驗和取樣程序通用指南 |
|
| BS ISO 8086-2004 |
乳品廠.衛生條件.檢驗和取樣程序通用指南 |
|
| BS ISO 8096-2005 |
雨衣用橡膠或塑料涂覆織物.規范 |
|
| BS ISO 8097-2001 |
航空器.經認證的航空成組裝運設備的最低飛行性能要求和試驗條件 |
Aircraft - Minimum airworthiness requirements and test conditions for certified air cargo unit load devices |
| BS ISO 8098-2002 |
自行車.兒童自行車的安全要求 |
Cycles - Safety requirements for bicycles for young children |
| BS ISO 8106-1995 |
玻璃容器.重量法測定容量.試驗方法 |
Glass containers - Determination of capacity by gravimetric method - Test method |
| BS ISO 8113-1995 |
玻璃容器.抗垂直負荷強度.試驗方法 |
Glass containers - Resistance to vertical load - Test method |
| BS ISO 8114-1993 |
紡織機械和附件.環錠紡紗機和并線機用錠子.等同術語目錄 |
Textile machinery and accessories - Spindles for ring-spinning and doubling machines - List of equivalent terms |
| BS ISO 8116-9-1993 |
紡織機械和附件.卷線軸.織物染色軸 |
Textile machinery and accessories - Beams for winding - Dyeing beams for textile fabrics |
| BS ISO 8117-2003 |
紡織機械.針織機.環型織機的公稱直徑 |
Textile machinery - Knitting machines - Nominal diameters of circular machines |
| BS ISO 8118-1993 |
織造機械. 圓柱形伸幅器 |
Weaving machines - Temple cylinders |
| BS ISO 8119-3-1994 |
紡織機械和附件.針織機械用針.術語.復合針 |
Textile machinery and accessories - Needles for knitting machines - Terminology - Compound needles |
| BS ISO 8121-1993 |
紡織機械.針織機.銘牌內容 |
Textile machinery - Knitting machines - Nameplate information |
| BS ISO 8122-2003 |
紡織機械.針織機.大標稱直徑圓形針織機的針數 |
(Textile machinery - Knitting machines - Number of needles for circular knitting machines of large nominal diameter) |
| BS ISO 8126-2000 |
縮微攝影技術.銀、重氮和多孔復制膠片.可視密度.規范和測量 |
Micrographics - Duplicating film, silver, diazo and vesicular - Visual density - Specifications and measurement. |
| BS ISO 8127-1-1990 |
縮微攝影技術.A6型縮微膠卷盒.16mm縮微膠卷用的5槽膠卷盒 |
Micrographics - A6 size microfilm jackets - Five-channel jacket for 16 mm microfilm |
| BS ISO 8127-2-1999 |
縮微攝影技術.A6型縮微膠卷盒.16mm和35mm縮微膠卷用的其它類型的膠卷盒 |
Micrographics - A6 size microfilm jackets - Other types of jacket for 16 mm and 35 mm microfilm |
| BS ISO 8131-1996 |
液壓傳動.單桿氣缸16MPa(160 bar)小型系列.公差 |
Hydraulic fluid power - Single rod cylinders, 16 MPa (160 bar) compact series - Tolerances |
| BS ISO 8132-1997 |
液壓傳動.160巴(16MPa)和250巴(25MPa)系列的單桿液壓缸.輔助設備安裝尺寸 |
Hydraulic fluid power - Single rod cylinders, 160 bar (16 MPa) medium and 250 bar (25 MPa) series - Mounting dimensions for accessories |
| BS ISO 8133-1997 |
液壓傳動.單桿液壓缸,16MPa小型.附件裝配尺寸 |
Hydraulic fluid power - Single rod cylinders, 16 MPa (160 bar) compact series - Accessory mounting dimensions |
| BS ISO 8135-1999 |
液壓傳動.160巴(16MPa)和250巴(25MPa)中型系列的單桿液壓缸.公差 |
Hydraulic fluid power - Single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series - Tolerances |
| BS ISO 8136-1997 |
液壓傳動.160巴(16MPa)中型系列單桿液壓缸.油口尺寸 |
Hydraulic fluid power - Single rod cylinders, 160 bar (16 MPa) medium series - Port dimensions |
| BS ISO 8137-1997 |
液壓傳動.250巴(25MPa)系列單桿液壓缸.油口尺寸 |
Hydraulic fluid power - Single rod cylinders, 250 bar (25 MPa) series - Port dimensions |
| BS ISO 8138-1999 |
液壓傳動.160巴(16MPa)小型系列單桿液壓缸.油口尺寸 |
Hydraulic fluid power - Single rod cylinders, 16 MPA (160 bar) compact series - Port dimensions |
| BS ISO 8139-1995 |
氣壓傳動.1000kPa(10巴)系列氣缸.活塞桿端球面孔.安裝尺寸 |
Pneumatic fluid power - Cylinders, 1 100 kPa (10 bar) series - Rod end spherical eyes - Mounting dimensions |
| BS ISO 8140-1995 |
氣壓傳動.1000KPa(10巴)系列的氣缸.連桿端形鉤.安裝尺寸 |
Pneumatic fluid power - Cylinders, 1 000 kPa (10 bar) series - Rod end clevis - Mounting dimensions |
| BS ISO 8178-10-2003 |
往復式內燃機.排放測量.壓燃式發動機瞬態工況排氣煙度現場測量用試驗周期和試驗方法 |
(Reciprocating internal combustion engines - Exhaust emission measurement - Test cycles and test procedures for field measurement of exhaust gas smoke emissions from compression ignition engines operat) |
| BS ISO 8178-3-1996 |
往復式內燃機.排氣污染測量.第3部分:在穩定狀態下排氣黑煙的測量方法 |
Reciprocating internal combustion engines - Exhaust emission measurement - Definitions and methods of measurement of exhaust gas smoke under steady state conditions |
| BS ISO 8178-7-1997 |
往復式內燃機.排氣污染測定.第7部分:發動機系列測量 |
Reciprocating internal combustion engines - Exhaust emission measurement - Engine family determination |
| BS ISO 8178-8-1997 |
往復式內燃機.排氣污染測定.第7部分:發動機系列測量 |
Reciprocating internal combustion engines - Exhaust emission measurement - Engine group determination |
| BS ISO 8178-9-2001 |
往復式內燃機.排氣污染測定.在瞬變條件下運行的壓燃式發動機廢煙氣排放的試驗臺測量用試驗周期和試驗程序 |
(Reciprocating internal combustion engines - Exhaust emission measurement - Test cycles and test procedures for test-bed measurement of exhaust gas smoke emissions from compression ignition engines ope) |
| BS ISO 8179-1-2004 |
球墨鑄鐵管.外部鍍鋅.終飾層用金屬鋅 |
|
| BS ISO 8199-2005 |
水質.培養的微生物計數方法通用指南 |
|
| BS ISO 8216-99-2002 |
石油產品.燃料.分類.總則 |
Petroleum products - Fuels (class F) - Classification - General |
| BS ISO 8229-1993 |
有關干洗機的操作和浸泡.詞匯 |
(Operations and baths relating to dry-cleaning machines - Vocabulary) |
| BS ISO 8254-1-2000 |
紙和紙板.鏡面光澤度的測量.用聚光束的75°光澤面TAPPI方法 |
(Paper and board - Measurement of specular gloss - 75 ?gloss with a converging beam, TAPPI method) |
| BS ISO 8254-3-2004 |
紙和紙板.光澤度的測量.用匯聚光束的20?光澤度的TAPPI法 |
|
| BS ISO 8257-1-1995 |
塑料.聚甲基丙烯酸甲酯(PMMA)模塑和擠壓材料.名稱與符號 |
(Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Designation) |
| BS ISO 8257-2-2002 |
塑料.聚甲基丙烯酸甲酯(PMMA)模塑和擠壓材料.試樣制備和性能測定 |
(Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Preparation of test specimens and determination of properties) |
| BS ISO 8296-2003 |
塑料.薄膜和薄板.濕潤表面張力的測定 |
(Plastics - Film and sheeting - Determination of wetting tension) |
| BS ISO 8297-1995 |
聲學.聲壓級環境評定用多源工廠聲功率級的測定.工程法 |
(Acoustics - Determination of sound power levels of multisource industrial plants for evaluation of sound pressure levels in the environment - Engineering method) |
| BS ISO 830-1999 |
貨運集裝箱.詞匯 |
(Freight containers - Vocabulary) |
| BS ISO 8312-2000 |
橡膠配料成份.硬脂酸.定義和試驗方法 |
Rubber compounding ingredients - Stearic acid - Definition and test methods |
| BS ISO 832-1995 |
文獻.文獻后參考書目.典型用詞的縮寫.兩種語言版 |
(Information and documentation - Bibliographic description and references - Rules for the abbreviation of bibliographic terms) |
| BS ISO 8323-1995 |
貨運集裝箱.空運/地面運輸氣、液集裝箱(交互型)規范和試驗 |
Freight containers - Air/surface (intermodel) general purpose containers - Specification and tests |
| BS ISO 8368-1999 |
水文測定.用構架對開放明渠的流量測定.構架選擇指南 |
(Hydrometric determinations - Flow measurements in open channels using structures - Guidelines for the selection of structure) |
| BS ISO 8371-1995 |
鐵礦石.爆裂系數的測定 |
(Iron ores - Determination of decrepitation index) |
| BS ISO 8374-2001 |
攝影.ISO安全光條件的測定 |
(Photography - Determination of ISO safelight conditions) |
| BS ISO 8379-1998 |
越野卡車.穩定性試驗 |
Rough terrain trucks - Stability tests |
| BS ISO 8388-1998 |
針織物.種類.詞匯 |
Knitted fabrics - Types - Vocabulary |
| BS ISO 8395-1995 |
電影攝影技術.發行影片用70mm帶有磁道的電影膠片再生產用試驗膠片.規范 |
Cinematography - Test films for the reproduction of 70 mm motion-picture release prints with magnetic stripes - Specifications |
| BS ISO 8405-1999 |
制模工具.圓柱頭頂桿的推頂套.一般用途的基本系列 |
Tools for moulding - Ejector sleeves with cylindrical head - Basic series for general purposes |
| BS ISO 8406-2001 |
鑄模用工具.鑄�；�.圓形定位件和墊片 |
Tools for moulding - Mould bases - Round locating elements and spacers |
| BS ISO 8419-2003 |
帶傳動.窄V帶.截面9N/J, 15N/J和25N/J(有效長度系列) |
Belt drives - Narrow V-belts - Sections 9N/J, 15N/J and 25N/J (lengths in the effective system) |
| BS ISO 8432-2001 |
香精油.用高性能液相色譜法分析.一般方法 |
Essential oils - Analysis by high performance liquid chromatography - General method |
| BS ISO 8434-2-1995 |
流體動力裝置及通用金屬管接頭.37°擴口管接頭 |
(Metallic tube connections for fluid power and general use - 37 ?flared fittings) |
| BS ISO 8434-3-1995 |
流體動力裝置及通用金屬管接頭.環形表面密封接頭 |
Metallic tube connections for fluid power and general use - O-ring face seal fittings |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com