標準號 |
中文名稱 |
英文名稱 |
| DIN EN ISO 10555-1-1999 |
一次性無菌管內導管.第1部分:一般要求 |
(Sterile, single-use intravascular catheters - Part 1: General requirements (ISO 10555-1:1995) (including Amendment A1:1999); German version EN ISO 10555-1:1996 + A1:1999) |
| DIN EN ISO 10555-1-2004 |
一次性使用無菌血管內導管.第1部分:一般要求 |
|
| DIN EN ISO 10555-2-1997 |
一次性使用無菌管內導管.第2部分:血管造影術用導管 |
(Sterile, single-use intravascular catheters - Part 2: Angiographic catheters (ISO 10555-2:1996); German version EN ISO 10555-2:1997) |
| DIN EN ISO 10555-3-1997 |
一次性使用無菌管內導管.第3部分:中心靜脈導管 |
(Sterile, single-use intravascular catheters - Part 3: Central venous catheters (ISO 10555-3:1996); German version EN ISO 10555-3:1997) |
| DIN EN ISO 10555-4-1997 |
一次性使用無菌管內導管.第4部分:球形擴張導管 |
(Sterile, single-use intravascular catheters - Part 4: Ballon dilatation catheters (ISO 10555-4:1996); German version EN ISO 10555-4:1997) |
| DIN EN ISO 10555-5-2000 |
一次性無菌管內導管.第5部分:與針頭相連的輔助導管 |
(Sterile, single-use intravascular catheters - Part 5: Over-needle peripheral catheters (ISO 10555-5:1996 + AMD 1:2000) (including corrigendum AC:1999 and AMD A1:2000); German version EN ISO 10555-5-1997 + AC:1999 + A1:2000) |
| DIN EN ISO 10563-1998 |
建筑結構.接合用密封料.測定質量和體積的變化 |
(Building construction - Sealants for joints - Determination of change in mass and volume (ISO 10563:1991); German version EN ISO 10563:1997) |
| DIN EN ISO 10563-2005 |
房屋建筑.密封膠.質量和體積變化的測定 |
|
| DIN EN ISO 10564-1997 |
軟釬焊材料和硬焊材料.分析用軟焊接取樣方法 |
(Soldering and brazing materials - Methods for the sampling of soft solders for analysis (ISO 10564:1993); German version EN ISO 10564:1997) |
| DIN EN ISO 10565-1998 |
油料種子.油和水分含量的同時測定.脈沖核磁共振譜測定法 |
(Oilseeds - Simultaneous determination of oil and water contents - Method using pulsed nuclear magnetic resonance spectrometry (ISO 10565:1998); German version EN ISO 10565:1998) |
| DIN EN ISO 10590-1998 |
建筑結構.密封膠.在維修和擴建時浸水后附著和粘聚性的測定 |
(Building construction - Sealants - Determination of adhesion/cohesion properties at maintained extension after immersion in water (ISO 10590:1991); German version EN ISO 10590:1997) |
| DIN EN ISO 10590-2005 |
房屋建筑.密封膠.浸水后在保持延伸狀態下測定密封膠的拉伸性能 |
|
| DIN EN ISO 10591-1998 |
建筑結構.密封膠.浸水后附著和粘聚性的測定 |
(Building construction - Sealants - Determination of adhesion/cohesion properties after immersion in water (ISO 10591:1991); German version EN ISO 10591:1997) |
| DIN EN ISO 10591-2005 |
房屋建筑.密封膠.浸水后密封膠的粘結/粘合性能測定 |
|
| DIN EN ISO 10592 Berichtigung 1-2001 |
DINENISO10592-1995的勘誤 |
(Corrigendum to DIN EN ISO 10592:1995 (German version EN ISO 10592:1995/A1:2000)) |
| DIN EN ISO 10592-1995 |
小艇.液體控制裝置 |
(Small craft - Hydraulic steering systems (ISO 10592:1994); German version EN ISO 10592:1995) |
| DIN EN ISO 1060-1-2000 |
塑料.氯乙烯的均聚物和共聚物樹脂.第1部分:命名體系和規范基礎 |
(Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 1: Designation system and basis for specifications (ISO 1060-1:1998); German version EN ISO 1060-1:1999) |
| DIN EN ISO 1060-2-2000 |
塑料.氯乙烯的均聚物和共聚物樹脂.第2部分:試樣的制備和性能的測定 |
(Plastics - Homopolymer and copolymer resins of vinyl chloride - Part 2: Preparation of test samples and determination of properties (ISO 1060-2:1998); German version EN ISO 1060-2:1999) |
| DIN EN ISO 1061-2000 |
塑料.不增塑的乙酸纖維素.游離酸度的測定 |
(Plastics - Unplasticized cellulose acetate - Determination of free acidity (ISO 1061:1990); German version EN ISO 1061:1999) |
| DIN EN ISO 10618-1999 |
碳纖維.樹脂浸漬紗線拉伸特性測定 |
(Carbon fibre - Determination of tensile properties of resin-impregnated yarn (ISO 10618:1999); German version EN ISO 10618:1999) |
| DIN EN ISO 10618-2004 |
碳纖維.樹脂浸漬紗拉伸性能的測定 |
|
| DIN EN ISO 10628-2001 |
工藝加工的流程圖.總則 |
(Flow diagrams for process plants - General rules (ISO 10628:1997); German version EN ISO 10628:2000) |
| DIN EN ISO 10634-1995 |
水質.含水介質中生物可降解性再測定用不易溶解在水中的有機化合物的制備和處理說明 |
(Water quality - Guidance for the preparation and treatment of poorly watersoluble organic compounds for the subsequent evaluation of their biodegradability in an aqueous medium (ISO 10634:1995); German version EN ISO 10634:1995) |
| DIN EN ISO 10637-2001 |
牙科設備.高和中容量抽吸系統 |
(Dental equipment - High- and medium-volume suction systems (ISO 10637:1999); German version EN ISO 10637:2000) |
| DIN EN ISO 10642-1998 |
內六角埋頭螺釘 |
(Hexagon socket countersunk head screws (ISO 10642:1997); German version EN ISO 10642:1997) |
| DIN EN ISO 10642-2004 |
內六角埋頭螺釘 |
|
| DIN EN ISO 10644-1998 |
帶平墊圈的螺釘和墊圈組件.墊圈硬度級別為200HV和300HV |
(Screw and washer assemblies with plain washers - Washer hardness classes 200 HV and 300 HV (ISO 10644:1998); German version EN ISO 10644:1998) |
| DIN EN ISO 10651-2-2004 |
醫用肺通氣機.基本安全和性能的特殊要求.第2部分:通氣機依賴型病人用家庭保健通氣機 |
|
| DIN EN ISO 10651-4-2002 |
醫用肺通氣機.電動呼吸機的專業要求 |
(Lung ventilators - Part 4: Particular requirements for operator-powered resuscitators (ISO 10651-4:2002); German version EN ISO 10651-4:2002) |
| DIN EN ISO 10651-6-2004 |
醫療用肺通氣機.基本安全和性能的特殊要求.第6部分:家庭保健通氣機支持設備 |
|
| DIN EN ISO 10664-2000 |
六角型內擰式螺栓和螺釘 |
(Hexalobular internal driving feature for bolts and screws (ISO 10664:1999); German version EN ISO 10664:1999) |
| DIN EN ISO 10664-2005 |
螺栓和螺釘用內板擰的六角花形 |
|
| DIN EN ISO 10666-2000 |
帶攻絲螺紋的自攻螺釘.機械和功能特性 |
(Drilling screws with tapping screw thread - Mechanical und functional properties (ISO 10666:1999); German version EN ISO 10666:1999) |
| DIN EN ISO 10669-1999 |
用于自攻螺絲及墊圈組件的平墊圈.普通及大號系列.A品級 |
(Plain washers for tapping screw and washer assemblies - Normal and large series - Product grade A (ISO 10669:1999); German version EN ISO 10669:1999) |
| DIN EN ISO 10673-1998 |
螺釘和墊圈組件用平墊圈.小型,標準和大型系列.產品等級A |
(Plain washers for screw and washer assemblies - Small, normal and large series - Product grade A (ISO 10673:1998); German version EN ISO 10673:1998) |
| DIN EN ISO 10683-2001 |
緊固件.非電解用鋅片覆層 |
(Fasteners - Non-electrolytically applied zinc flake coatings (ISO 10683:2000); German version EN ISO 10683:2000) |
| DIN EN ISO 10684-2004 |
緊固件.熱浸鍍鋅涂層 |
|
| DIN EN ISO 10692-1-2003 |
儲氣瓶.微電子工業用儲氣瓶閥接頭.第1部分:輸出口接頭 |
(Gas cylinders - Gas cylinder valve connections for use in the microelectronic industry - Part 1: Outlet connections (ISO 10692-1:2001); German version EN ISO 10692-1:2001) |
| DIN EN ISO 10692-2-2003 |
儲氣瓶.微電子工業用儲氣瓶閥接頭.第2部分:儲氣瓶閥接頭的規范和型式試驗 |
(Gas cylinders - Gas cylinder valve connections for use in the microelectronic industry - Part 2: Specification and type testing for valve to cylinder connections (ISO 10692-2:2001); German version EN ISO 10692-2:2001) |
| DIN EN ISO 10695-2000 |
水質.所選有機氮和磷化合物的測定.氣相色譜法 |
(Water quality - Determination of selected organic nitrogen and phosphorus compounds - Gas chromatographic methods (ISO 10695:2000); German version EN ISO 10695:2000) |
| DIN EN ISO 10700-1996 |
鋼和鐵.錳含量的測定.火焰原子吸收光譜分析法 |
(Steel and iron - Determination of manganese content - Flame atomic absorption spectrometric method (ISO 10700:1994); German version EN ISO 10700:1995) |
| DIN EN ISO 10705-1-2002 |
水質.噬菌體的測定和計數.第1部分:特殊FRNA噬菌體的計數 |
(Water quality - Detection and enumeration of bacteriophages - Part 1: Enumeration of F-specific RNA bacteriophages (ISO 10705-1:1995); German version EN ISO 10705-1:2001) |
| DIN EN ISO 10705-2-2002 |
水質.噬菌體的測定和計數.第2部分:體內大腸桿菌噬菌體的計數 |
(Water quality - Detection and enumeration of bacteriophages - Part 2: Enumeration of somatic coliphages (ISO 10705-2:2000); German version EN ISO 10705-2:2001) |
| DIN EN ISO 10707-1998 |
水質.含水介質中有機物全需氧生物降解的測定.生物化學需氧量測定法(封閉瓶試驗) |
(Water quality - Evaluation in an aqueous medium of the “ultimate“ aerobic biodegradability of organic compounds - Method by analysis of biochemical oxygen demand (closed bottle test) (ISO 10707:1994); German version EN ISO 10707:1997) |
| DIN EN ISO 10712-1996 |
水質.假單胞菌屬還蛋白生長抑制試驗(假單胞菌屬珍惜細胞增生抑制試驗) |
(Water quality - Pseudomonas putida growth inhibition test (Pseudomonas cell multiplication inhibition test) (ISO 10712:1995); German version EN ISO 10712:1995) |
| DIN EN ISO 10714-2002 |
鋼和鐵.測定磷含量.磷礬鉬酸鹽分光光度法 |
(Steel and iron - Determination of phosphorus content - Phosphovanadomolybdate spectrophotometric method (ISO 10714:1992); German version EN ISO 10714:2002) |
| DIN EN ISO 10715-2000 |
天然氣.取樣導則 |
(Natural gas - Sampling guidelines (ISO 10715:1997); German version EN ISO 10715:2000) |
| DIN EN ISO 10723-2003 |
天然氣.在線分析系統的性能評定 |
(Natural gas - Performance evaluation for on-line analytical systems (ISO 10723:1995); German version EN ISO 10723:2002) |
| DIN EN ISO 10724-1-2002 |
塑料.熱固粉末模塑復合物試樣的噴射模塑成型.第1部分:一般原理和多用途試樣的模塑成型 |
(Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 1: General principles and moulding of multipurpose test specimens (ISO 10724-1:1998); German version EN ISO 10724-1:2001) |
| DIN EN ISO 10724-2-2000 |
塑料.熱固性粉末模塑復合物試樣的噴射鑄造法.第2部分:小板材 |
(Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 2: Small plates (ISO 10724-2:1998); German version EN ISO 10724-2:2000) |
| DIN EN ISO 10806-2004 |
管道工程.波紋狀金屬軟管用配件 |
|
| DIN EN ISO 10807-1997 |
管道工程.在爆燃性空氣中電纜保護用皺紋軟金屬軟管組件 |
(Pipework - Corrugated flexible metallic hose assemblies for the protection of electrical cables in explosive atmospheres (ISO 10807:1994); German version EN ISO 10807:1996) |
| DIN EN ISO 10819-1996 |
機械振動和沖擊.手臂振動.手套在手掌對振動可傳性的評定和測量方法 |
(Mechanical vibration and shock - Hand-arm vibration - Method for the measurement and evaluation of the vibration transmissibility of gloves at the palm of the hand (ISO 10819:1996); German version EN ISO 10819:1996) |
| DIN EN ISO 10821-2005 |
工業縫紉機械.縫紉機械、設備和系統的安全要求.(ISO 10821-2005); 德文版本 EN ISO 10821-2005 |
|
| DIN EN ISO 10846-1-1999 |
聲學和振動.彈性件的振動-聲傳輸特性的實驗室測量法.第1部分:規則和指南 |
(Acoustics and vibration - Laboratory measurement of vibro-acoustic transfer properties of resilient elements - Part 1: Principles and guidelines (ISO 10846-1:1997); German version EN ISO 10846-1:1998) |
| DIN EN ISO 10846-2-1999 |
聲學和振動.彈性件的振動-聲傳輸特性的實驗室測量法.第2部分:移動振動用彈性支撐件的動態傳輸剛性的測 |
(Acoustics and vibration - Laboratory measurement of vibro-acoustic transfer properties of resilient elements - Part 2: Dynamic stiffness of elastic supports for translatory motion; direct method (ISO 10846-2:1997); German version EN ISO 10846-2:1998) |
| DIN EN ISO 10846-3-2003 |
聲學和振動.彈性件的振動-聲傳輸特性的實驗室測量.第3部分:平動用彈性支架的動態勁度的間接測定方法 |
(Acoustics and vibration - Laboratory measurement of the vibro-acoustic properties of resilient elements - Part 3: Indirect method for determination of the dynamic stiffness of resilient supports for translatory motion (ISO 10846-3:2002); German version E |
| DIN EN ISO 10846-4-2004 |
聲學和振動.彈性件的振動-聲傳輸特性的實驗室測量.第4部分:平動用除彈性支撐外的構件的動態勁度 |
(Acoustics and vibration - Laboratory measurement of the vibro-acoustic transfer properties of resilient elements - Part 4: Dynamic stiffness of elements other than elastic supports for translatory motion (ISO 10846-4:2003); German version EN ISO 10846-4) |
| DIN EN ISO 10846-4-2004 |
聲學和振動.彈性件的振動-聲傳輸特性的實驗室測量.第4部分:平動用除彈性支撐外的構件的動態勁度 |
|
| DIN EN ISO 10882-1-2001 |
焊接及相關工藝中的健康和安全.工作人員工作區氣載粒子和氣體的取樣.第1部分:氣載粒子取樣 |
(Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operator`s breathing zone - Part 1: Sampling of airborne particles (ISO 10882-1:2001); German version EN ISO 10882-1:2001) |
| DIN EN ISO 10882-2-2001 |
焊接及相關工藝中的健康和安全.工作人員工作區氣載粒子和氣體的取樣.第2部分:氣體取樣 |
(Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operator`s breathing zone - Part 2: Sampling of gases (ISO 10882-2:2000); German version EN ISO 10882-2:2000) |
| DIN EN ISO 10938-1998 |
眼科儀器.圖表放映機 |
(Ophthalmic instruments - Chart projectors (ISO 10938:1998); German version EN ISO 10938:1998) |
| DIN EN ISO 10939-1998 |
眼科設備.顯微裂隙燈 |
(Ophthalmic instruments - Slit-lamp microscopes (ISO 10939:1998); German version EN ISO 10939:1998) |
| DIN EN ISO 10940-1998 |
眼科器械.眼底照相機 |
(Ophthalmic instruments - Fundus cameras (ISO 10940:1998); German version EN ISO 10940:1998) |
| DIN EN ISO 10942 Berichtigung 1-1998 |
對DINENISO10942:1998-06的校正 |
(Corrigenda to DIN EN ISO 10942:1998-06 (EN ISO 10942:1998/AC:1998)) |
| DIN EN ISO 10942-1998 |
眼科器械.眼底鏡直接檢查 |
(Ophthalmic instruments - Direct ophthalmoscopes (ISO 10942:1998); German version EN ISO 10942:1998) |
| DIN EN ISO 10943-1998 |
眼科器械.眼底鏡間接檢查 |
(Ophthalmic instruments - Indirect ophthalmoscopes (ISO 10943:1998); German version EN ISO 10943:1998) |
| DIN EN ISO 10944-1998 |
眼科器械.同視鏡 |
(Ophthalmic instruments - Synoptophores (ISO 10944:1998); German version EN ISO 10944:1998) |
| DIN EN ISO 10960-1996 |
橡膠和塑料軟管.在動力條件下耐臭氧性的評定 |
(Rubber and plastics hoses - Assessment of ozone resistance under dynamic conditions (ISO 10960:1994); German version EN ISO 10960:1996) |
| DIN EN ISO 10964-1997 |
粘合劑.螺紋緊固件上厭氧粘合劑的抗扭強度的測定 |
(Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993); German version EN ISO 10964:1997) |
| DIN EN ISO 10993-1 Berichtigung 1-1999 |
對DINENISO10993-1:1998-06的校正 |
(Corrigenda to DIN EN ISO 10993-1:1998-06) |
| DIN EN ISO 10993-1-1998 |
醫療器械的生物評定.第1部分:評定和試驗 |
(Biological evaluation of medical devices - Part 1: Evaluation and testing (ISO 10993-1:1997); German version EN ISO 10993-1:1997) |
| DIN EN ISO 10993-10-2003 |
醫療器械的生物評定.第10部分:刺激與延遲式超靈敏性試驗 |
(Biological evaluation of medical devices - Part 10: Tests for irritation and delayed-type hypersensitivity (ISO 10993-10:2002); German version EN ISO 10993-10:2002) |
| DIN EN ISO 10993-11-1995 |
醫療裝置生物學評定.第11部分:系統毒性試驗 |
(Biological evaluation of medical devices - Part 11: Tests for systemic toxicity (ISO 10993-11:1993); German version EN ISO 10993-11:1995) |
| DIN EN ISO 10993-12-1996 |
醫療器械的生物評定.第12部分:樣品制備和參考材料 |
(Biological evaluation of medical devices - Part 12: Sample preparation and reference materials (ISO 10993-12:1996); German version EN ISO 10993-12:1996) |
| DIN EN ISO 10993-13-1999 |
醫學化合物的生物評定.第13部分:聚合醫學化合物中降解物的質量和數量驗證 |
(Biological evaluation of medical devices - Part 13: Identification and and quantification of degradation products from polymeric medical devices (ISO 10993-13:1998); German version EN ISO 10993-13:1998) |
| DIN EN ISO 10993-14-2002 |
醫療器械的生物評定.第14部分:陶瓷降解產品的識別與量化 |
(Biological evaluation of medical devices - Part 14: Identification and quantification of degradation products from ceramics (ISO 10993-14:2001); German version EN ISO 10993-14:2001) |
| DIN EN ISO 10993-15-2001 |
醫療器械的生物評定.第15部分:金屬及合金中降解產物的識別與量化 |
(Biological evaluation of medical devices - Part 15: Identification and quantification of degradation products from metals and alloys (ISO 10993-15:2000); German version EN ISO 10993-15:2000) |
| DIN EN ISO 10993-16-1997 |
醫療器械的生物評定.第12部分:對退化產品和可濾清物的毒理動力學研究的方案和計算 |
(Biological evaluation of medical devices - Part 16: Toxicokinetic study design for degradation products and leachables (ISO 10993-16:1997); German version EN ISO 10993-16:1997) |
| DIN EN ISO 10993-17-2003 |
醫療器械的生物評定.第17部分:可浸出物質容許限值的確定 |
(Biological evaluation of medical devices - Part 17: Establishment of allowable limits for leachable substances (ISO 10993-17:2002); German version EN ISO 10993-17:2002) |
| DIN EN ISO 10993-18-2005 |
醫療裝置的生物評價.第18部分:材料的化學表征 |
|
| DIN EN ISO 10993-2-1998 |
醫療器械的生物評定.第2部分:動物保護的要求 |
(Biological evaluation of medical devices - Part 2: Animal welfare requirements (ISO 10993-2:1992); German version EN ISO 10993-2:1998) |
| DIN EN ISO 10993-3-2004 |
醫療器械的生物學評價.第3部分:遺傳毒性、致癌性和生殖毒性的試驗 |
(Biological evaluation of medical devices - Part 3: Tests for genotoxicity, carcinogenicity and reproductive toxicity (ISO 10993-3:2003); German version EN ISO 10993-3:2003) |
| DIN EN ISO 10993-3-2004 |
醫療器械的生物學評價.第3部分:遺傳毒性、致癌性和生殖毒性的試驗 |
|
| DIN EN ISO 10993-4-2003 |
醫療器械的生物評定.第4部分:與血液相互作用的選擇試驗 |
(Biological evaluation of medical devices - Part 4: Selection of tests for interactions with blood (ISO 10993-4:2002); German version EN ISO 10993-4:2002) |
| DIN EN ISO 10993-5-1999 |
醫療器械的生物評定.第5部分:細胞毒性試驗:試管內方法 |
(Biological evaluation of medical devices - Part 5: Tests for cytotoxicity: in vitro-methods (ISO 10993-5:1999); German version EN ISO 10993-5:1999) |
| DIN EN ISO 10993-7-1995 |
醫學產品的生物評定.第7部分:環氧乙烷的滅菌殘渣 |
(Biological evaluation of medical devices - Part 7: Ethylene oxide sterilization residuals (ISO 10993-7:1995); German version EN ISO 10993-7:1995) |
| DIN EN ISO 10993-8-2001 |
醫療裝置的生物評價.第8部分:生物試驗用標準物質的選擇和合格鑒定 |
(Biological evaluation of medical devices - Part 8: Selection and qualification of reference materials for biological tests (ISO 10993-8:2000); German version EN ISO 10993-8:2000) |
| DIN EN ISO 10993-9-1999 |
醫療裝置生物評定.第9部分:用于勢降解產物識別與評定的結構 |
(Biological evaluation of medical devices - Part 9: Framework for identification and quantification of potential degradation products (ISO 10993-9:1999); German version EN ISO 10993-9:1999) |
| DIN EN ISO 11058-1999 |
土工織物和土工織物相關產品.對平面,無負載,一般的水滲透性測定 |
Geotextiles and geotextile-related products - Determination of water permeability characteristics normal to the plane, without load (ISO 11058:1999); German version EN ISO 11058:1999 |
| DIN EN ISO 11064-1-2001 |
控制中心的人類工效學設計.第1部分:控制中心的設計原則 |
(Ergonomic design of control centres - Part 1: Principles for the design of control centres (ISO 11064-1:2000), German version EN ISO 11064-1:2000) |
| DIN EN ISO 11064-2-2001 |
控制中心的人類工效學設計.第2部分:控制室的布置原則 |
(Ergonomic design of control centres - Part 2: Principles for the arrangement of control suites (ISO 11064-2:2000); German version EN ISO 11064-2:2000) |
| DIN EN ISO 11064-3 Berichtigung 1-2003 |
DINENISO11064-3的技術勘誤 |
(Corrigenda to DIN EN ISO 11064-3:2000-09 (EN ISO 11064-3:1999/AC:2002)) |
| DIN EN ISO 11064-3-2000 |
控制中心的人類工效設計.第3部分:控制室布置 |
(Ergonomic design of control centres - Part 3: Control room layout (ISO 11064-3:1999); German version EN ISO 11064-3:1999) |
| DIN EN ISO 11064-4-2004 |
控制中心的人類工效學設計.第4部分:工作站的布置和尺寸 |
|
| DIN EN ISO 11064-6-2005 |
控制中心人類工效學設計.第6部分:控制中心環境要求 |
|
| DIN EN ISO 1107-2003 |
漁網.網片.基本術語和定義 |
(Fishing nets - Netting - Basic terms and definitions (ISO 1107:2003); German version EN ISO 1107:2003) |
| DIN EN ISO 11070-1999 |
一次性無菌管內導管導引器 |
(Sterile single-use intravascular catheter introducers (ISO 11070:1998); German version EN ISO 11070:1999) |
| DIN EN ISO 11091-1999 |
建筑制圖.園林設計制圖實用規程 |
(Construction drawings - Landscape drawing practice (ISO 11091:1994); German version EN ISO 11091:1999) |
| DIN EN ISO 1110-1998 |
塑料.聚酰胺.試樣的加速預處理 |
(Plastics - Polyamides - Accelerated conditioning of test specimens (ISO 1110:1995); German version EN ISO 1110:1997) |
| DIN EN ISO 11102-1-1997 |
內燃機.手柄起動裝置.第1部分:安全技術要求和檢驗 |
(Reciprocating internal combustion engines - Handle starting equipment - Part 1: Safety requirements and tests (ISO 11102-1:1997); German version EN ISO 11102-1:1997) |
| DIN EN ISO 11102-2-1997 |
內燃機.手柄起動裝置.第2部分:測量脫扣距離和角度的方法 |
(Reciprocating internal combustion engines - Handle starting equipment - Part 2: Method of testing the angle of disengagement (ISO 11102-2:1997); German version EN ISO 11102-2:1997) |
| DIN EN ISO 11105-1997 |
小型船舶.裝有強制點火發動機和/式油罐的房屋通風 |
(Small craft - Ventilation of petrol engine and/or petrol tank compartments (ISO 11105:1997); German version EN ISO 11105:1997) |
| DIN EN ISO 11111-1-2005 |
紡織機械.安全要求.第1部分:通用要求 |
|
| DIN EN ISO 11111-2-2005 |
紡織機械.安全要求.第2部分:紡紗預備和紡紗機械 |
|
| DIN EN ISO 11111-3-2005 |
紡織機械.安全要求.第3部分:無紡機械 |
|
| DIN EN ISO 11111-4-2005 |
紡織機械.安全要求.第4部分:紗線加工和繩索制造機械 |
|
| DIN EN ISO 11111-5-2005 |
紡織機械.安全要求.第5部分:織造和針織用預備機械 |
|
| DIN EN ISO 11111-6-2005 |
紡織機械.安全要求.第6部分:織物織造機械 |
|
| DIN EN ISO 11111-7-2005 |
紡織機械.安全要求.第7部分:染色和精整機械 |
|
| DIN EN ISO 11114-1-1998 |
可運輸氣瓶.裝有氣體的氣瓶及其閥門材料的可互換性.第1部分:金屬材料 |
(Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 1: Metallic materials (ISO 11114-1:1997)(includes corrigendum AC:1998); German version EN ISO 11114-1:1997) |
| DIN EN ISO 11114-2-2001 |
可運輸氣瓶.裝有氣體的氣瓶及其閥門材料的可互換性.第2部分:非金屬材料 |
(Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials (ISO 11114-2:2000); German version EN ISO 11114-2:2000) |
| DIN EN ISO 11114-3-1998 |
可運輸氣瓶.氣瓶和含氣閥門材料的可兼容性.第3部分:有氧環境中自燃試驗 |
(Transportable gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 3: Autogenous ignition test in oxygen atmosphere (ISO 11114-3:1997)(including corrigendum AC:1998); German version EN ISO 11114-3:1997 + AC:1998) |
| DIN EN ISO 11114-4-2005 |
移動氣瓶.氣瓶和瓶閥材料與盛裝氣體的相容性.第4部分:選擇耐氫脆的金屬材料的試驗方法 |
|
| DIN EN ISO 11116-1-2000 |
移動式氣瓶.氣瓶.閥門與氣體瓶連接用17E錐型螺紋.第1部分:規范 |
(Transportable gas cylinders - Gas cylinders; 17E taper thread for connection of valves to gas cylinders - Part 1: Specification (ISO 11116-1:1999); German version EN ISO 11116-1:1999) |
| DIN EN ISO 11116-2-1999 |
可移動的氣罐.煤氣罐.閥門與氣罐連接的17E錐型螺紋.第1部分:檢驗量規 |
(Transportable gas cylinders - Gas cylinders; 17E taper thread for connection of valves to gas cylinders - Part 2: Inspection gauges (ISO 11116-2:1999); German version EN ISO 11116-2:1999) |
| DIN EN ISO 11120-1999 |
可移動的煤氣瓶.儲氣容積在150立升至3000立升之間的密封煤氣運輸用無縫可重新填裝的大型鋼瓶.設計,結構和檢 |
(Gas cylinders - Refillable seamless steel tubes water capacity between 150 l and 3000 l - Designconstruction and testing (ISO 11120:1999); German version EN ISO 11120:1999) |
| DIN EN ISO 11124-1-1997 |
用涂層材料涂覆前鋼表面的準備工作.金屬噴射清潔材料的要求.第1部分:一般介紹和分類 |
(Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 1: General introduction and classification (ISO 11124-1:1993); German version EN ISO 11124-1:1997) |
| DIN EN ISO 11124-2-1997 |
用涂層材料涂覆前鋼表面的準備工作.金屬噴射清潔材料的要求.第2部分:冷硬鑄鐵砂粒 |
(Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 2: Chilled-iron grit (ISO 11124-2:1993); German version EN ISO 11124-2:1997) |
| DIN EN ISO 11124-3-1997 |
用涂層材料涂覆前鋼表面的準備工作.金屬噴射清潔材料的要求.第3部分:高碳鑄鋼噴丸及砂粒 |
(Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 3: High-carbon cast-steel shot and grit (ISO 11124-3:1993); German version EN ISO 11124-3:1997) |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com