標準號 |
中文名稱 |
英文名稱 |
| DIN 65516-1984 |
航空和航天.鋼制.短螺紋.有內鋸齒和MJ螺紋的圓柱頭螺釘.溫度235℃以下.額定抗拉強度900MPa |
(Aerospace; cheese head bolts with internal serration thread, short thread, steel, nominal tensile strength 900 MPa, for temperatures up to 235 C) |
| DIN 65517-2002 |
航空和航天.溫度315℃以下.額定抗拉強度1100MPa的鈦合金.短螺紋有內鋸齒帶MJ螺紋的圓柱頭螺釘.溫度315℃以 |
(Aerospace - Cheese head bolts, close tolerance, with bihexagon socket and MJ thread, short thread, titanium alloy, nominal tensile strength 1100 MPa, for temperatures up to 315 鳦) |
| DIN 65518-1984 |
航空和航天.鈦合金.短螺紋.有肋條平錐頭十字槽和MJ螺紋的平頭螺釘.溫度315℃以下.額定抗拉強度1100MPa |
(Aerospace; pan head bolts with ribbed TORQ-SET (ACR) recess and MJ-thread, short thread, titanium alloy, nominal tensile strength 1100 MPa, for temperatures up to 315 C) |
| DIN 65519-1984 |
航空和航天.短螺紋.鋼制.有肋條平錐頭十字槽和MJ螺紋的平頭螺釘.溫度可達235℃.額定抗拉強度900MPa |
(Aerospace; pan head bolts with ribbed TORQ-SET (ACR) recess and MJ-thread, short thread, steel, nominal tensile strength 900 MPa, for temperatures up to 235 C) |
| DIN 65520-1984 |
航空和航天.短螺紋.鋼制.有肋平錐頭十字槽和MJ螺紋的平頭配合螺釘.溫度可達235℃.額定抗拉強度900MPa |
(Aerospace; pan head bolts, close tolerance, with ribbed TORQ-SET (ACR) recess an MJ-thread, short thread, steel, nominal tensile strength 900 MPa, for temperatures up to 235 C) |
| DIN 65521-1-1984 |
航空和航天.平錐頭十字槽.肋形狀.尺寸 |
(Aerospace; TORQ-SET and ACR; dimensions) |
| DIN 65521-2-1984 |
航空與航天.翼形十字槽.裝筋板.深度規 |
(Aerospace; TORQ-SET and ACR; penetration gauges) |
| DIN 65521-3-1984 |
航空與航天.翼形十字槽.筋條螺釘旋具尖端 |
(Aerospace; TORQ-SET and ACR; screwdriver points) |
| DIN 65522-1984 |
航空和航天.螺紋接近于頭部.不銹鋼制.具有MJ螺紋的六角頭螺釘.溫度可達425℃.額定抗拉強度700MPa |
(Aerospace; screws, hexagon, with MJ-thread, threaded opproximatley to head, corrosion-resisting steel, nominal tensile strength 700 MPa, for temperatures up to 425 C) |
| DIN 65523-1984 |
航空和航天.不銹鋼制.短螺紋.具有MJ螺紋的六角頭螺釘.溫度可達425℃.額定抗拉強度700MPa |
(Aerospace; hexagon bolts, with MJ-thread, short thread, corrosion-resisting steel, nominal tensile strength 700 MPa, for temperatures up to 425 C) |
| DIN 65524-1984 |
航空和航天.鋼制.短螺紋.具有MJ螺紋的六角頭螺釘.溫度可達235℃.額定抗拉強度900MPa |
(Aerospace; heaxagon bolts, with MJ-thread, short thread, steel, nominal tensile strength 900 MPa, for temperatures up to 235 C) |
| DIN 65525-1992 |
航空和航天.帶鋼制MJ短螺紋的六角螺釘.溫度235℃以下額定抗拉強度1100MPa |
(Aerospace; bolts, hexagon, close tolerance, with MJ-thread, short thread, steel, nominal tensile strength 1100 MPa, for temperatures up to 235 C) |
| DIN 65526-1998 |
航空和航天.帶MJ螺紋,短螺紋,鈦合金鋼制六角配合螺釘.溫度315℃及其以下用額定抗拉強度1100MPa |
(Aerospace - Hexagon bolts, close tolerance, with short-length MJ thread, titanium alloy - Nominal tensile strength 1100 MPa, for temperatures up to 315 C) |
| DIN 65527-1984 |
航空和航天.短螺紋.鋼制.具有MJ螺紋的六角頭緊公差螺釘.溫度可達235℃.額定抗拉強度1100MPa |
(Aerospace; hexagon bolts, close tolerance, with MJ-thread, short thread, steel, nominal tensile stregth 1100 MPa, for temperatures up to 235 C) |
| DIN 65528-1984 |
航空航天.自鎖、鋼制帶圓柱深沉孔和凸緣的有MJ螺紋的十二角螺母.等級:1550MPa/1800MPa/235℃ |
(Aerospace; nuts, bihexagonal with flange and MJ-thread, deep counterbore, self-locking, steel, class: 1550 MPa/1800 MPa/235 鳦) |
| DIN 65528-2005 |
航空航天系列.鋼制自鎖緊、帶深沉孔、凸緣和MJ螺紋的十二角螺母.等級:1550MPa/1800MPa/235℃ |
|
| DIN 65529-1984 |
航空航天.自鎖、鋼制帶圓柱形深沉孔和凸緣及MJ螺紋的十二角螺母.等級:1250MPa/235℃ |
(Aerospace; nuts, bihexagonal with flange and MJ-thread, deep counterbore, self-locking, steel, class: 1250 MPa/235 鳦) |
| DIN 65529-2005 |
航空航天系列.鋼制自鎖緊、帶深沉孔、凸緣和MJ螺紋的十二角螺母.等級:1250MPa/235℃ |
|
| DIN 65530-1989 |
航空航天.自鎖、耐腐蝕鋼制、帶圓柱形深沉孔和凸緊及MJ螺紋的十二角螺母.等級.1550MPa/315℃/425℃ |
(Aerospace; nuts, bihexagonal, with flange and MJ thread, deep counterbore, self-locking, corrosion-resisting steel, classification: 1550 MPa/315 鳦/425 鳦) |
| DIN 65531-1984 |
航空航天.自鎖、耐腐蝕鋼制帶圓柱形深沉孔和凸緊及MJ螺紋的十二角螺母.等級:1100MPa/1250MPa/315℃/425℃ |
(Aerospace; nuts, bihexagonal with flange and MJ-thread, deep counterbore, self-locking, corrosion-resisting, steel, class: 1100 MPa/1250 MPa/315 鳦/425 鳦) |
| DIN 65531-2005 |
航空航天系列.耐腐蝕鋼制自鎖緊、帶深沉孔、凸緣和MJ螺紋的十二角螺母.等級:1250 MPa/315 鳦/425 鳦 |
|
| DIN 65532-1984 |
航空和航天.螺紋槽符合DINISO5855的MJ螺紋的螺紋末端和螺紋退刀槽 |
(Aerospace; runouts, undercuts and thread ends for MJ-threads to DIN ISO 5855) |
| DIN 65533-1987 |
航空和航天.螺釘和螺母.原材料和配置及表面處理.推薦.選擇 |
(Aerospace; bolts, screws and nuts; allocation of materials and surface treatments; recommended selection) |
| DIN 65534-1992 |
航空和航天.帶耐蝕鋼制MJ螺紋的六角螺母.等級:1100/650℃ |
(Aerospace; nuts, hexagon, with MJ-thread, corrosion resisting steel; classification: 1100 MPa/650 C) |
| DIN 65535-1986 |
航空航天.耐腐蝕鋼制帶MJ螺紋的自鎖螺母同槽組件(螺母板).螺母間距為固定的或選定的.等級:1100MPa/315℃ |
(Aerospace; gang channel nut assembly, with self-locking nuts with MJ thread, nut spacing fixed or optional, in corrosion-resisting steel; class: 1100 MPa/315 鳦) |
| DIN 65536-1-1986 |
航空和航天.銅合金制螺釘鎖定的導線螺紋接頭.等級:1100MPa/425℃ |
(Aerospace; inserts, helical coil threads, screw-locking, copper alloy; class: 1100 MPa/425 C) |
| DIN 65536-2-1986 |
航空和航天.銅合金制螺釘鎖定的導線螺紋接頭.安裝和工具 |
(Aerospace; inserts, helical coil threads, screw-locking, copper alloy; assembly and special tools) |
| DIN 65537-1987 |
航空和航天.帶內齒和MJ螺紋.短螺紋.鎳合金制圓柱形螺栓.抗拉強度1250MPa.溫度315℃/425℃以下 |
(Aerospace; cheese head bolts with bihexagon socket and MJ thread, short thread, nickel alloy; nominal tensile strength 1250 MPa, for temperatures up to 315 C/425 C) |
| DIN 65538-1987 |
航空和航天.帶內齒和MJ螺紋.短螺紋.鎳合金制圓柱形螺栓.額定抗拉強度1250MPa.溫度315℃/425℃以下 |
(Aerospace; cheese head bolts, close tolerance, with bihexagon socket and MJ thread, short thread, nickel alloy; nominal tensile strength 1250 MPa, for temperatures up to 315 C/425 C) |
| DIN 65541-1987 |
航空和航天.帶筋翼形十字槽和MJ螺紋.螺紋接近頭部.鎳合金制平頭螺栓.額定抗拉強度1250MPa.溫度315℃/425℃ |
(Aerospace; pan head bolts with ribbed TORQ-SET (ACR) recess and MJ thread; fully threaded, nickel alloy; nominal tensile strength 1250 MPa, for temperatures up to 315 C/425 C) |
| DIN 65542-1987 |
航空和航天.具有筋翼形十字槽和MJ螺紋.短螺紋.鎳合金制埋頭配合螺栓.額定抗拉強度1250MPa.溫度315℃/425℃ |
(Aerospace; countersunk head screws, close tolerance, with ribbed TORQ-SET (ACR) recess and MJ thread, short thread length, nickel alloy, nominal tensile strength 1250 MPa, for temperatures up to 315 C/425 C) |
| DIN 65546-1985 |
航空航天.帶圓柱形深沉孔、帶凸緊及MJ螺紋的自鎖及耐腐蝕鋼十二角螺母.等級:1100MPa/315℃/425℃ |
(Aerospace; nuts, bihexagonal with flange and MJ-thread, deep counterbore, self-locking, corrosion-resisting steel; class: 1100 MPa/315 鳦/425 鳦) |
| DIN 65546-2005 |
航空航天系列.耐腐蝕鋼制自鎖緊、帶深沉孔、凸緣和MJ螺紋的十二角螺母.等級:1100 MPa/315 鳦/425 鳦 |
|
| DIN 65547-1987 |
航空和航天.公制系列.鈦合金鋼制.帶通用頭配合鉚釘 |
(Aerospace; rivets, close tolerance, with protruding head, metric series, titanium alloy) |
| DIN 65548-1987 |
航空和航天.鈦合金鋼制.公制系列.帶埋頭100°配合鉚釘 |
(Aerospace; rivets, close tolerance with 100 flush head, metric series, titanium alloy) |
| DIN 65549-1987 |
航空和航天.鈦合金鋼制.公制系列.帶埋頭130°配合鉚釘 |
(Aerospace; rivets, close tolerance with 130 flush head, metric series, titanium alloy) |
| DIN 65550-1987 |
航空和航天.公制系列.鈦制.帶箍閉合環 |
(Aerospace; flanged collars, metric series, titanium) |
| DIN 65551-1988 |
航空和航天.公制系列不銹鋼制盲鉚釘.帶漸縮埋頭100℃鉚芯 |
(Aerospace; blind rivets with 100 reduced countersunk head, metric series, corrosion-resisting steel, with mandrel) |
| DIN 65552-1993 |
航空和航天.米制系列帶鉚芯100°沉頭不銹鋼盲鉚釘 |
(Aerospace; blind rivets with 100 countersunk head, corrosion-resisting steel, with mandrel, metric series) |
| DIN 65553-2001 |
航空和航天.帶MJ螺紋鉚接螺母用無孔金屬墊片 |
(Aerospace - Shims, without hole, for anchor nuts with MJ thread; Not to be used for new designs) |
| DIN 65554-1987 |
航空和航天.具有筋翼形十字槽和MJ螺紋.短螺紋.耐腐蝕鋼制平頭螺栓.額定抗拉強度1100MPa.溫度可達425℃ |
(Aerospace; pan head bolts with ribbed TORQ-SET (ACR) recess and short-length MJ thread, corrosion-resisting steel, nominal tensile strength 1100 MPa, for temperatures up to 425 C) |
| DIN 65555-1987 |
航空和航天.帶MJ螺紋.短螺紋.耐腐蝕鋼制六角螺栓.額定抗拉強度1100MPa.溫度可達425℃ |
(Aerospace; hexagon bolts with short-length MJ thread, corrosion-resisting steel; nominal tensile strength 1100 MPa, for temperatures up to 425 C) |
| DIN 65557-1989 |
航空和航天.帶肋翼形螺紋接近頭部.鈦合金制.十字槽及MJ螺紋的平頭螺釘.額定拉伸強度1100MPa溫度至315℃ |
(Aerospace; pan head screws with ribbed TORQ-SET (ACR) recess and MJ thread, fully threaded, titanium alloy; nominal tensile strength 1100 MPa, for temperatures up to 315 C) |
| DIN 65558-1989 |
航空和航天.帶肋翼形全螺紋.鈦合金制.十字槽及MJ螺紋的沉頭螺釘.額定拉伸強度1100MPa.溫度至315℃ |
(Aerospace; countersunk head screws, with ribbed TORQ-SET (ACR) recess and MJ thread, fully threaded, titanium alloy; nominal tensile strength 1100 MPa, for temperatures up to 315 C) |
| DIN 65559-1991 |
航空和航天.纖維增強塑料.多向?qū)訅喊宓臋z驗.缺口抗拉強度的測定 |
(Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of open-hole tensile strength) |
| DIN 65560-1991 |
航空和航天.纖維增強塑料.多向?qū)訅喊宓臋z驗.缺口抗壓強度的測定 |
(Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of filled-hole compressive strength) |
| DIN 65561-1991 |
航空和航天.纖維增強塑料.多向?qū)訅喊宓臋z驗.沖擊負荷后抗壓強度的測定 |
(Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of compressive strength after impact test) |
| DIN 65562-1991 |
航空和航天.纖維增強塑料.多向?qū)訅核芰系臋z驗.孔壁強度的測定 |
(Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of bearing strength) |
| DIN 65564-1992 |
航空和航天.增強纖維.用HPLC法作碳素長絲紗、織物和短切原絲的漿成份的定性測定 |
(Aerospace; reinforcement fibres; qualitative determination of size constituents of carbon filament yarns, woven fabrics and chopped strands by HPLC) |
| DIN 65565-1992 |
航空和航天.增強纖維.用紅外分光法作碳素長絲紗、織物和短切原絲的漿型的定性控制 |
(Aerospace; reinforcement fibres; qualitative testing of size type of carbon filament yarns, woven fabrics and chopped strands by infrared spectroscopy) |
| DIN 65566-1992 |
航空和航天.增強纖維.碳素長絲紗、織物和短切原絲的漿成份的測定 |
(Aerospace; reinforcement fibres; determination of size content of carbon filament yarns, woven fabrics and chopped strands) |
| DIN 65567-1992 |
航空和航天.增強纖維.芳族聚酰胺長絲紗,織物和短切原絲整理劑含量測定 |
(Aerospace; reinforcement fibres; determination of finish content of aramid filament yarns, woven fabrics and chopped strands) |
| DIN 65568-1992 |
航空和航天.增強纖維.碳素長絲紗、織物和短切原絲的熱氧化穩定性的測定 |
(Aerospace; reinforcement fibres; determination of thermal oxidative resistance of carbon filament yarns, woven fabrics and short cuts) |
| DIN 65569-1-1992 |
航空和航天.增強纖維.復絲紗厚度的測定.懸浮法 |
(Aerospace; reinforcement fibres; determination of density of filament yarns; sink-float method) |
| DIN 65569-2-1992 |
航空和航天.增強纖維.復絲紗厚度的測定.浮力法 |
(Aerospace; reinforcement fibres; determination of density of filament yarns; hydrostatic weighing method) |
| DIN 65570-1990 |
航空和航天.熱處理設備.一般要求 |
(Aerospace; heat treatment facilities; general requirements) |
| DIN 65571-1-1992 |
航空和航天.增強纖維.長絲紗截面面積和長絲直徑的測定.計算方法 |
(Aerospace; reinforcement fibres; determination of filament diameter and cross-sectional area of filament yarns; calculation method) |
| DIN 65571-2-1992 |
航空和航天.增強纖維.長絲紗的長絲直徑的測定.縱向投影法 |
(Aerospace; reinforcement fibres; determination of filament diameter of filament yarns; longitudinal projection method) |
| DIN 65571-3-1992 |
航空和航天.增強纖維.長絲紗的長絲直徑、長絲截面形式和長絲截面面積的測定.橫磨測量 |
(Aerospace; reinforcement fibres; determination of filament diameter, cross-sectional shape and area of filament yarns; measurement of transverse micro-section) |
| DIN 65571-4-1992 |
航空和航天.增強纖維.長絲紗的長絲直徑的測定.激光干涉儀測量 |
(Aerospace; reinforcement fibres; determination of filament diameter of filament yarns; laser interferometry) |
| DIN 65572-1992 |
航空和航天.碳化纖維和無反應熱塑塑料制單色直接配制預浸膠體.交貨技術條件 |
(Aerospace; unidirectional sheet and tape prepreg from carbon fibres and non-reactive thermoplastics; technical specification) |
| DIN 65574-1993 |
航空和航天.部件銘牌.結構規范 |
(Aerospace; nameplates; directions for design) |
| DIN 65576-1991 |
航空和航天.帶固定凸輪桿和單鎖定解脫裝置的不銹鋼快卸銷 |
(Aerospace; quick-release pins in corrosion-resisting steel, single locked, with self-retaining cam lever release mechanism) |
| DIN 65578-1991 |
航空和航天.帶推或拉單鎖定解脫裝置不銹鋼快卸銷 |
(Aerospace; quick-release pins in corrosion-resisting steel, single locked, with pull or push release mechanism) |
| DIN 65581-1992 |
航空和航天.公制系列.鈦合金制緊配合鉚釘和純鈦制閉鎖環.交貨技術條件 |
(Aerospace; titanium-alloy close-tolerance rivets and pure-titanium collars, metric series; technical specification) |
| DIN 65582-1990 |
航空和航天.鋁和鎂合金鑄件的熱處理 |
(Aerospace; heat treatment of aluminium- and magnesium-alloy castings) |
| DIN 65583-1999 |
航空和航天.纖維增強塑料.動態負荷下纖維粘合材料的玻璃過渡的測定 |
(Aerospace - Fibre reinforced materials - Determination of glass transition of fibre composites under dynamic load) |
| DIN 65587-1992 |
航空和航天.輸送帶.交貨技術條件 |
(Aerospace; webbing; technical specification) |
| DIN 65590-1992 |
航空和航天.編織亞麻制品.交貨技術條件 |
(Aerospace; braided cord; technical specification) |
| DIN 65591-1998 |
航空和航天.非涂層寬幅織物.交貨技術條件 |
(Aerospace - Broad woven fabric, uncoated - Technical specification) |
| DIN 65594-1993 |
航空和航天.英制系列平頭實心鉚釘?shù)你T釘上頭 |
(Aerospace; closing heads for solid rivets, pan head, inch based series) |
| DIN 65595-1993 |
航空和航天.米制系列平頭實心鉚釘?shù)你T釘上頭 |
(Aerospace; closing heads for solid rivets; pan head, metric series) |
| DIN 65597-1993 |
航空和航天.纖維增強塑料.放熱反應時溫差的測定 |
(Aerospace; fibre reinforced plastics; determination of temperature difference on exothermic reaction) |
| DIN 65598-1993 |
航空和航天.纖維增強塑料.層壓制品裂紋頻度測定 |
(Aerospace; fibre reinforced plastics; determination of cracking frequency on laminates) |
| DIN 65603-1982 |
航空和航天.鉆模上9.9mm以下的鉆孔色標 |
(Aerospace; colour identification of holes up to 9,9 mm on drilling jigs) |
| DIN 65604-1988 |
航空和航天.特種檢驗裝置.顏色標記 |
(Aerospace; special gauging facilities; colour identification) |
| DIN 65629-1993 |
航空和航天.碳纖維和非活性熱塑塑料制預浸漬布片和布帶.交貨技術條件 |
(Aerospace; fabric sheet and tape prepreg from carbon fibres and non-reactive thermoplastics; technical specification) |
| DIN 65668-1998 |
航空和航天.為了基本粒子計數而使油料稀釋 |
(Aerospace series - Dilution of oils for the purpose of particles counting) |
| DIN 65669-1-1996 |
航空和航天.測定用過的液體過濾器件污染情況的方法.第1部分:通過材料試樣提取作重力測定固體污染情況 |
(Aerospace series - Methods for determining the contamination of used fluid filter elements - Part 1: Gravimetric determination of particulate contamination by taking material samples) |
| DIN 65673-1999 |
航空和航天.纖維增強塑料.紗疵,織疵和預浸漬體疵點.定義 |
(Aerospace - Fibre reinforced plastics - Description of yarn, fabric and prepreg defects) |
| DIN 65736-1-1984 |
航空和航天.單槽.螺釘材料1.1174.7和1.4544.9.沉頭螺釘靜負荷時的螺釘計算值 |
(Aerospace; bolt calculation values, static load, for countersunk head bolts, single shear, bolt materials 1.1174.7 and 1.4544.9) |
| DIN 65736-3-1984 |
航空和航天.單槽.螺釘材料1.7220.5.沉頭螺釘靜負荷時的螺釘計算值 |
(Aerospace; bolt calculation values, static load, for countersunk head bolts, single shear, bolt material 1.7220.5) |
| DIN 65736-5-1984 |
航空和航天.單槽.螺釘材料1.4944.4和1.7734.5.沉頭螺釘靜負荷時的螺釘計算值 |
(Aerospace; bolt calculation values, static load, for countersunk head bolts, single shear, bolt materials 1.4944.4 and 1.7734.5) |
| DIN 65736-7-1984 |
航空和航天.單槽.螺釘材料1.6604.6.沉頭螺釘靜負荷時的螺釘計算值 |
(Aerospace; bolt calculation values, static load, for countersunk head bolts, single shear, bolt material 1.6604.6) |
| DIN 6580-1985 |
切削工藝的概念.切削過程的運動和幾何形態 |
(Terminology of chip removing; movements and geometry of the chip removing process) |
| DIN 6581-1985 |
切削工藝的概念.刀具切削部分的參考系統和角度 |
(Terminology of chip removing; reference systems and angles on the cutting part of the tool) |
| DIN 6582-1988 |
切削工藝的概念.刀具 |
(Terminology of cutting; additional terms for the tool, wedge and the cutting edge) |
| DIN 6583-1981 |
切削工藝的概念.刀具壽命概念 |
(Terms of cutting procedures; tool life criteria) |
| DIN 6584-1982 |
切削工藝的概念.切削力.能量.切削功.功率 |
(Terms of the cutting technique; forces, energy, work, power) |
| DIN 659-1982 |
管制套筒板手 |
(Tubular single end tee socket wrenches) |
| DIN 6590-1986 |
平面刃硬質合金無固定孔轉位式刀片 |
(Indexable hardmetall (carbide) inserts with wiper edges, without fixation hole) |
| DIN 6594-1998 |
轉位式刀片用符合DIN69893-1A型要求的帶圓錐空心桿和冷卻潤滑劑導槽的鉆頭 |
(Drills with hollow taper shanks and coolant fluid supply according to DIN 69893-1 type A for indexable inserts - Main dimensions) |
| DIN 6595-1993 |
帶轉位刀片的鉆頭.直柄 |
(Drills with indexable inserts; parallel shanks) |
| DIN 6596-1998 |
轉位式刀片用符合DIN69893-1A型要求的帶圓錐空心桿和冷卻潤滑劑導槽的鉆頭.標識 |
(Drills with hollow taper shanks and coolant fluid supply according to DIN 69893-1 type A for indexable inserts - Designation) |
| DIN 6597-2004 |
可轉位刀片用符合DIN 69893-1和DIN 69893-2的外部和內部旋轉帶中空錐柄的工具夾.名稱與符號 |
|
| DIN 6598-2004 |
可轉位刀片用符合DIN 69893-1的外部和內部旋轉帶中空錐柄的工具夾.與尺寸相關的概述 |
|
| DIN 6599-1998 |
切削機械用硬質切銷材料的可用性 |
(Applicability of hard cutting materials for machining by chip removal - Information additional to ISO 513 designation (ISO/TR 11255:1994)) |
| DIN 66-1990 |
符合DINISO7721要求.通用沉頭螺釘頭的傾斜度 |
(Countersinks for countersunk head screws with ISO 7721 common head style) |
| DIN 660-1993 |
半圓頭鉚釘.公稱直徑1至8mm |
(Round head rivets; nominal diameters 1 to 8 mm) |
| DIN 6600-1989 |
存儲污染水的易燃和不易燃液體用的鋼制容器(罐).質量監督 |
(Steel tanks for the storage of flammable and non-flammable water polluting liquids; concepts and inspection) |
| DIN 66000-1985 |
信息處理.開關代數的數學符號 |
(Information processing; switching algebra, mathematical signs and symbols) |
| DIN 66001 Bb.1-1983 |
信息處理.示意圖符號及其用途.符號樣板上示意圖的排列 |
(Information processing; graphical symbols and their application; layout of graphical symbols on a template) |
| DIN 66001-1983 |
信息處理.示意圖符號及其用途 |
(Information processing; graphical symbols and their application) |
| DIN 66002-1975 |
信息處理；數字０和大寫字母Ｏ的手寫體 |
(Information processing; handwriting of the digit 0 and of the upper case letter O) |
| DIN 66003-1999 |
信息處理.7位代碼 |
(Information technology - 7-bit code) |
| DIN 66004-1-1983 |
信息處理.數據載體編碼.在孔帶25上的7位碼的表達方法 |
(Information processing; coding on data media; representation of 7-bit code character sets on punched tape 25) |
| DIN 66004-2-1982 |
信息處理.數據載體編碼.在穿孔卡上的7位碼和8位碼的表達方法 |
(Information processing; coding on data media; representation of 7-bit coded and 8-bit coded character sets on punched cards) |
| DIN 66004-3-1983 |
信息處理.數據載體編碼.在磁帶12上的7位碼和8位碼的表達方法 |
(Information processing; coding on data media; representation of 7-bit coded and 8-bit coded character sets on magnetic tape 12) |
| DIN 66004-4-1982 |
信息處理.數據載體編碼.在盒式磁帶3.8上的7位碼和8位碼的表達方法 |
(Information processing; coding on data media; representation of 7-bit coded and 8-bit coded character sets on magnetic tape cassette 3,8) |
| DIN 66004-5-1999 |
信息處理.數據載體編碼.第5部分:在軟盤上的7位碼和8位碼的表達方法 |
(Information processing - Coding on data media - Part 5: Representation of 7-bit coded and 8-bit coded set on media-flexible disk cartridge) |
| DIN 66005-1988 |
信息處理.在有9個磁道記錄的磁帶12上純數字數據節省空間的顯示 |
(Information processing; representation of packed numerics and binary data recorded on 9 tracks on magnetic tape 12) |
| DIN 66008-1-1989 |
機械光學字符識別用字體A.字符和公稱尺寸 |
(Font A for optical character recognition; characters and nominal dimensions) |
| DIN 66008-6-1985 |
機械光學字符識別用字體A.字符與公稱尺寸.字符集的擴展 |
(Font A for optical character recognition; characters and nominal dimensions; extension of the character set) |
| DIN 66008-7-1985 |
機械光學字符識別用字體A.字符的9×9點陣的表示 |
(Font A for optical character recognition; representation of characters by dots in a 99 matrix) |
| DIN 66009-1977 |
機械光學字符識別用字體B.字符.公稱尺寸和字符載體上的格式 |
(Font B for optical character recognition; characters, nominal dimensions, and format) |
| DIN 6601-1991 |
鋼制容器/儲罐的材料對液體的耐蝕性(正性液體表) |
(Resistance of materials of steel tanks against liquids (positiv-list of liquids)) |
| DIN 66010-1988 |
信息處理存儲和交換數字數據用軟磁數據載體.概念 |
(Information processing; flexible magnetic data media, for the storage and the interchange of digital data; concepts) |
| DIN 66013-1977 |
數字數據存儲用7磁道的不歸零制記錄磁帶.位密度8位/毫米 |
(On 7 tracks nonreturn to zero (one) recorded magnetic tape for digital data storage, density 8 rpmm (200 rpi)) |
| DIN 66014-1-1977 |
數字數據存儲用9磁道的不歸零制記錄磁帶.位密度8位/毫米 |
(On 9 track nonreturn to zero (one) recorded magnetic tape for digital data storage, density 8 rpmm (200rpi)) |
| DIN 66014-2-1977 |
數字數據存儲用9磁道的不歸零制記錄磁帶.位密度32位/毫米 |
(On 9 tracks nonretorn to zero (one) recorded magnetic tape for digital data storage, density 32 rpmm (800 rpi)) |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com