標準號 |
中文名稱 |
英文名稱 |
| DIN ISO 799-1988 |
造船.領航員扶梯 |
(Shipbuilding; pilot ladders; identical with ISO 799, edition 1986) |
| DIN ISO 7991-1998 |
玻璃.熱平均線性膨脹系數的測定 |
(Glass - Determination of coefficient of mean linear thermal expansion (ISO 7991:1987)) |
| DIN ISO 7996-1990 |
環境空氣.氧化氮含量濃度的測定.化學發光法 |
(Ambient air; determination of the mass concentration of nitrogen oxides; chemiluminescence method; identical with ISO 7996:1985) |
| DIN ISO 8002-1995 |
機械振動.地面車輛.報告測量數據的方法 |
(Mechanical vibrations - Land vehicles - Method for reporting measured data; identical with ISO 8002:1986) |
| DIN ISO 8013-1993 |
硫化橡膠.壓縮或切變的蠕變測定 |
(Rubber, vulcanized; determination of creep in compression or shear; identical with ISO 8013:1988) |
| DIN ISO 8015-1986 |
技術制圖.公差標注基本原則 |
(Technical drawings; fundamental tolerancing principle; identical with ISO 8015, edition 1985) |
| DIN ISO 8016-1989 |
農業機械.整體輪轂的車輪 |
(Machinery for agriculture; wheels with integral hub; identical with ISO 8016:1985) |
| DIN ISO 8020-2003 |
沖壓工具.有圓柱頭和直桿或者縮徑柄的沖頭 |
(Tools for pressing - Punches with cylindrical head and straight or reduced shank (ISO 8020:2002)) |
| DIN ISO 8027-1986 |
道路車輛.客車用空氣過濾器構件.尺寸 |
(Road vehicles; air filter elements for passenger cars; dimensions; identical with ISO 8027, edition 1984) |
| DIN ISO 8036-1-2003 |
光學和光學儀器.顯微鏡.第1部分:通常用于光學顯微術的浸油 |
(Optics and optical instruments - Microscopes - Part 1: Immersion oil for general use in light microscopy (ISO 8036-1:1998)) |
| DIN ISO 8037-1-2003 |
光學和光學儀器.顯微鏡.載玻片.第1部分:尺寸、光學性能和標志 |
(Optics and optical instruments - Microscopes; Slides - Part 1: Dimensions, optical properties and marking (ISO 8037-1:1986)) |
| DIN ISO 8039-2001 |
光學和光學儀器.顯微鏡.放大 |
(Optics and optical instruments - Microscopes - Magnification (ISO 8039:1997)) |
| DIN ISO 8040-2003 |
光學和光學儀器.顯微鏡.鏡筒導板和鏡筒槽的連接尺寸 |
(Optics and optical instruments - Microscopes - Dimensions of tube slide and tube slot connections (ISO 8040:2001)) |
| DIN ISO 8061-1992 |
高山雪橇緊固.松脫力矩值選擇 |
(Alpine ski-bindings; selection of release torque values; identical with ISO 8061:1991) |
| DIN ISO 8062-1998 |
鑄件.尺寸公差和加工留量 |
(Castings - System of dimensional tolerances and machining allowances (ISO 8062:1994)) |
| DIN ISO 8090-2000 |
自行車.術語.與ISO8090:1990等同 |
(Cycles - Terminology; Identical with ISO 8090:1990) |
| DIN ISO 8093-1986 |
道路車輛.電子系統的故障判斷試驗 |
(Road vehicles; diagnostic testing of electronic systems; identical with ISO 8093, edition 1985) |
| DIN ISO 8114-1997 |
紡織機械和附件.環錠紡紗機和環錠捻線機用錠子.等義術語一覽表 |
(Textile machinery and accessories - Spindles for ring-spinning and doubling machines - List of equivalent terms (ISO 8114:1990)) |
| DIN ISO 8115-1989 |
棉包.尺寸和密度 |
(Cotton bales; dimensions and density; identical with ISO 8115:1986) |
| DIN ISO 8115-2-1997 |
棉包.第2部分:人造棉纖維的棉包.尺寸 |
(Bales - Part 2: Bales of man-made staple fibres - Dimensions (ISO 8115-2:1994)) |
| DIN ISO 8115-3-1997 |
棉包.第3部分:棉纖維棉包.包裝和加標簽 |
(Bales - Part 3: Bales of cotton, packaging and labelling (ISO 8115-3:1995)) |
| DIN ISO 8116-1-1997 |
紡織機械和附件.絡紗經軸.第1部分:一般概念 |
(Textile machinery and accessories - Beams for winding - Part 1: General vocabulary (ISO 8116-1:1995)) |
| DIN ISO 8116-2-1997 |
紡織機械和附件.絡紗經軸.第2部分:整經軸 |
(Textile machinery and accessories - Beams for winding - Part 2: Warper`s beams (ISO 8116-2:1995)) |
| DIN ISO 8116-3-1997 |
紡織機械和附件.絡紗經軸.第3部分:織軸 |
(Textile machinery and accessories - Beams for winding - Part 3: Weaver`s beams (ISO 8116-3:1995)) |
| DIN ISO 8116-4-1997 |
紡織機械和附件.絡紗經軸.第4部分:織軸.整經軸和分段軸用法蘭品質分級 |
(Textile machinery and accessories - Beams for winding - Part 4: Quality classification of flanges for weaver`s beams, warper`s beams and sectional beams (ISO 8116-4:1995)) |
| DIN ISO 8116-5-1997 |
紡織機械和附件.絡紗徑軸.第5部分:經紗織機的分段織軸 |
(Textile machinery and accessories - Beams for winding - Part 5: Sectional beams for warp knitting machines (ISO 8116-5:1995)) |
| DIN ISO 8116-6-1997 |
紡織機械和附件.絡紗經軸.第6部分:織帶和織針帶用經軸 |
(Textile machinery and accessories - Beams for winding - Part 6: Beams for ribbon weaving and ribbon knitting (ISO 8116-6:1995)) |
| DIN ISO 8116-7-1997 |
紡織機械和附件.絡紗經軸.第7部分:纖維梳條和紗線用染色經軸 |
(Textile machinery and accessories - Beams for winding - Part 7: Beams for dyeing slivers, rovings and yarns (ISO 8116-7:1995)) |
| DIN ISO 8116-8-1997 |
紡織機械和附件.絡紗經軸.第8部分:跳動誤差測量的定義和方法 |
(Textile machinery and accessories - Beams for winding - Part 8: Definitions of run-out tolerances and methods of measurement (ISO 8116-8:1995)) |
| DIN ISO 8117-1990 |
紡織機械.針織機.環型織機的公稱直徑 |
(Textile machinery; knitting machines; nominal diameters of circular machines; identical with ISO 8117:1986) |
| DIN ISO 8118-1988 |
織機.邊撐圓筒 |
(Temple cylinders for weaving machines; identical with ISO 8118:1986) |
| DIN ISO 8119-1-1990 |
紡織機械和附件.針織機用針.術語.第1部分:閂鎖式針 |
(Textile machinery and accessories; needles for knitting machines; terminology; latch-type needles; identical with ISO 8119-1:1989) |
| DIN ISO 8119-2-1990 |
紡織機械和附件.針織機用針.術語.第2部分:鉤針 |
(Textile machinery and acessories; neddles for knitting machines; terminology; bearded needles; identical with ISO 8119-2:1989) |
| DIN ISO 8119-3-1993 |
紡織機械和附件.針織機用針.術語.復合針 |
(Textile machinery and accessories; needles for knitting machines; terminology; compound needles; identical with ISO 8119-3:1992) |
| DIN ISO 812-2004 |
硫化橡膠.低溫脆性的測定 |
|
| DIN ISO 8121-1990 |
紡織機械.針織機.銘牌內容 |
(Textile machinery; knitting machines; nameplate information; identical with ISO 8121:1986) |
| DIN ISO 8122-1991 |
紡織機械.織機.大直徑環形針織機的針號 |
(Textile machinery; knitting machines; number of needles for circular knitting machines of large nominal diameter; identical with ISO 8122:1988) |
| DIN ISO 8122-2004 |
紡織機械.針織機.大公稱直徑圓機的針數 |
|
| DIN ISO 8123-1997 |
道路車輛.起動發動機徑節小齒輪 |
(Road vehicles - Diametral pitch starter motor pinions (ISO 8123:1991)) |
| DIN ISO 813-2004 |
硫化或熱塑性橡膠.與剛性底粘合強度的測定.90?剝離法 |
|
| DIN ISO 8130-1-2005 |
粉末涂料.第1部分:用篩分法測定粒度分布 |
|
| DIN ISO 8130-2-2005 |
粉末涂料.第2部分:用氣體比較比重瓶測定密度 |
|
| DIN ISO 8130-3-2005 |
粉末涂料.第3部分:用浮子式液體比重瓶測定密度 |
|
| DIN ISO 8130-4-2005 |
粉末涂料.第4部分:降低爆裂極限值的計算 |
|
| DIN ISO 8130-5-2005 |
粉末涂料.第5部分:粉末/空氣混合物流動特性的測定 |
|
| DIN ISO 8139-1990 |
氣液傳動.10巴系列氣缸.桿端球面環孔配件.裝配尺寸 |
(Pneumatic fluid power; cylinders, 10 bar series; rod end spherical eyes; mounting dimensions; identical with ISO 8139:1986) |
| DIN ISO 8140-1991 |
氣動傳動.10巴(1000kPa)系列氣缸.活塞桿U形叉.裝配尺寸 |
(Pneumatic fluid power; cylinders, 10 bar series; rod end clevis; mounting dimensions; identical with ISO 8140:1986) |
| DIN ISO 8146-1986 |
造船.長形孔板桅桿 |
(Shipbuilding; oval eyeplates; identical with ISO 8146, edition 1985) |
| DIN ISO 8148-1986 |
造船.懸臂起重機吊桿頂端裝置.固定型 |
(Shipbiulding; derrick head fittings, fixed type; identical with ISO 8148, edition 1985) |
| DIN ISO 815-2000 |
硫化或熱塑性橡膠.在環境溫度、高溫或低溫下壓縮永久變形的測定 |
(Rubber, vulcanized or thermoplastic - Determination of compression set at ambient, elevated or low temperatures (ISO 815:1991 + ISO 815:1991/Cor.1:1993)) |
| DIN ISO 8216-0-1991 |
石油產品.燃料(F類).分類.總則 |
(Petroleum products; fuel (class F); classification; general; identical with ISO 8216-0:1986) |
| DIN ISO 8216-1-1991 |
石油產品.燃料(F類).分類.第1部分:船用燃料種類 |
(Petroleum products; fuels (class F); classification; categories of marine fuels; identical with ISO 8216-1:1986) |
| DIN ISO 8217-1993 |
石油產品.動力燃料(F類).對船用燃料的要求 |
(Petroleum products; fuels (class F); specifications of marine fuels; identical with ISO 8217:1987) |
| DIN ISO 8226-1-1998 |
紙和紙板.濕膨脹性的測量.第1部分:最大相對濕度達到68%的濕膨脹性 |
(Paper and board - Measurement of hygroexpansivity - Part 1: Hygroexpansivity up to a maximum relative humidity of 68 % (ISO 8226-1:1994)) |
| DIN ISO 8239-1990 |
縫紉機.縫紉機縫針.裝配尺寸.公差和配合 |
(Sewing machines; sewing machine needles; fitting dimensions; tolerances and combinations; identical with ISO 8239:1987) |
| DIN ISO 8243-1992 |
卷煙.取樣 |
(Cigarettes; sampling; identical with ISO 8243:1991) |
| DIN ISO 8253-1-1992 |
聲學.聽力測試方法.第1部分:基本純音空氣傳導和骨傳導聽閾測聽術 |
(Acoustics; audiometric test methods; part 1: basic pure tone air and bone conduction threshold audiometry; identical with ISO 8253-1:1989) |
| DIN ISO 8253-2-1994 |
聲學.聽力試驗方法.第2部分:純音和窄頻帶信號聲場測聽術 |
(Acoustics - Audiometric test methods - Part 2: Sound field audiometry with pure tone and narrow-band test signals; identical with ISO 8253-2:1992) |
| DIN ISO 8255-1-2003 |
光學和光學儀器.顯微鏡.蓋玻璃.第1部分:尺寸公差、厚度和光學性能 |
(Optics and optical instruments - Microscopes; Cover glasses - Part 1: Dimensional tolerances, thickness and optical properties (ISO 8255-1:1986)) |
| DIN ISO 8277-1989 |
船舶制造.管道工程.信息傳輸 |
(Shipbuilding; information processing; pipework; information transfer; identical with ISO 8277:1988) |
| DIN ISO 8291-1987 |
釉瓷和搪瓷.自潔性能的試驗方法 |
(Vitreous and porcelain enamels; method of test of self-cleaning properties; identical with ISO 8291, edition 1986) |
| DIN ISO 8297-2000 |
聲學.環境中聲壓級評定用多源工業設備聲功率級的測定.工程法 |
(Acoustics - Determination of sound power levels of multisource industrial plants for evaluation of sound pressure levels in the environment - Engineering method (ISO 8297:1994)) |
| DIN ISO 8314-1988 |
造船.跨架軸承和導向滑塊軸承的樞軸配件 |
(Shipbuilding and marine structures; trunnion pieces for span bearings and lead block bearings; identical with ISO 8314, edition 1987) |
| DIN ISO 8356-1985 |
道路車輛.柴油發動機.22型螺旋擰入式噴油嘴 |
(Road vehicles; diesel engines; screw-in injector; type 22; identical with ISO 8356, edition 1984) |
| DIN ISO 8362-1-1990 |
注射容器及附件.第1部分:用玻璃管制成的注射劑小瓶 |
(Injection containers for injectables and accessories; injection vials made of glass tubing; identical with ISO 8362-1:1989) |
| DIN ISO 8362-2-1989 |
注射容器及附件.第2部分:注射瓶的封口 |
(Injection containers for injectables and accessories; closures for injection vials; identical with ISO 8362-2:1988) |
| DIN ISO 8362-3-1990 |
注射劑用的注射容器和附件.第3部分:注射劑小瓶用的鋁帽 |
(Injection containers for injectables and accessories; aluminium caps for injection vials; identical with ISO 8362-3:1989) |
| DIN ISO 8362-4-1996 |
注射容器及附件.第4部分:由模壓玻璃制成的盛注射劑的小瓶 |
(Injection containers for injectables and accessories - Part 4: Injection vials made of moulded glass (ISO 8362-4:1989)) |
| DIN ISO 8362-5-1996 |
注射容器及附件.第2部分:注射劑小瓶用冷動干燥塞子 |
(Injection containers for injectables and accessories - Part 5: Freeze drying closures for injection vials (ISO 8362-5:1995)) |
| DIN ISO 8362-6-1993 |
注射容器及附件.注射小瓶用鋁塑合成材料制帽蓋 |
(Injection containers for injectables and accessories; caps made of aluminium-plastics combinations for injection vials; identical with ISO 8362-6:1992) |
| DIN ISO 8362-7-1996 |
注射容器及附件.第7部分:無重疊塑料部件的由鋁和塑料復合物制的注射小瓶帽蓋 |
(Injection containers for injectables and accessories - Part 7: Injection caps made of aluminium-plastics combinations without overlapping plastics part (ISO 8362-7:1995)) |
| DIN ISO 8364-2000 |
高山雪撬和捆綁裝置.捆綁安裝面.要求和試驗方法 |
(Alpine skis and bindings - Binding mounting area - Requirements and test methods (ISO 8364:1999)) |
| DIN ISO 8374-2003 |
攝影技術.ISO安全光條件的測定 |
(Photography - Determination of ISO safelight conditions (ISO 8374:2001)) |
| DIN ISO 8405-2000 |
鑄模工具.圓柱頭脫模頂銷.一般用途的基本系列 |
(Tools for moulding - Ejector sleeves with cylindrical head - Basic series for general purposes (ISO 8405:1998)) |
| DIN ISO 8406-2002 |
鑄模用工具.鑄�；�.圓形定位件和襯墊 |
(Tools for moulding - Moulded bases - Round locating elements and spacers (ISO 8406:2001)) |
| DIN ISO 8426-1994 |
液壓傳動.液壓泵和液壓電動機.導出容積的測定 |
(Hydraulic fluid power; positive displacement pumps and motors; determination of derived capacity; identical with ISO 8426:1988) |
| DIN ISO 8454-1997 |
卷煙.煙霧氣相中一氧化碳含量的測定.非色散紅外分析法 |
(Cigarettes - Determination of carbon monoxide in the vapour phase of cigarette smoke - NDIR method (ISO 8454:1995)) |
| DIN ISO 8466-2-2000 |
水質.水的性能特性分析方法和評價方法的校準與計算.第2部分:非線性二級校準方程的校準方法 |
(Water quality - Calibration and evaluation of analytical methods and estimation of performance characteristics - Part 2: Calibration strategy for non-linear second order calibration functions (ISO 8466-2:1993)) |
| DIN ISO 8466-2-2004 |
水質.性能特征分析方法和評價方法的校準和計算.第2部分:使用非線性二級校準方程的方法 |
|
| DIN ISO 8468-1993 |
船橋設計和裝備.要求和導則 |
(Ship`s bridge layout and associated equipment; requirements and guidelines; identical with ISO 8468:1990) |
| DIN ISO 8470-1993 |
道路車輛.帶平底座和16mm平面寬度的M14×1.25火花塞和在汽缸蓋座孔 |
(Road vehicles; M14 ?1,25 spark-plugs with flat seating and 16 mm hexagon and their cylinder head housing; identical with ISO 8470:1990 (status as of 1993)) |
| DIN ISO 8471-1989 |
數據傳輸用按位存取控制方法.HDLC.高級數據鏈控制的過程平衡等級.轉換設備中數據鏈的分層尋址判定.轉移 |
(High-level data link control procedures, HDLC; address resolution/negotiation in asynchronous balanced mode over switched circuit; identical with ISO 8471:1987) |
| DIN ISO 8485-1991 |
信息處理.程序設計語言.APL |
(Information processing; programming language APL; identical with ISO 8485:1989) |
| DIN ISO 8486-1-1997 |
粘接磨料制磨具.粒度分布的測定和標識.第1部分:F4至F220磨粒 |
(Bonded abrasives - Determination and designation of grain size distribution - Part 1: Macrogrits F4 to F220 (ISO 8486-1:1996)) |
| DIN ISO 8486-2-1997 |
粘接磨料制磨具.粒度分布的測定和標識.第2部分:F230至F1200的磨粒 |
(Bonded abrasives - Determination and designation of grain size distribution - Part 2: Microgrits F230 to F1200 (ISO 8486-2:1996)) |
| DIN ISO 8489-1-1997 |
紡織機械和附件.圓錐形筒管.第1部分:推薦的主要尺寸 |
(Textile machinery and accessories - Cones for cross winding - Part 1: Recommended main dimensions (ISO 8489-1:1995)) |
| DIN ISO 8489-2-1997 |
紡織機械和附件.圓錐形圓筒.第2部分:帶3°30＇半錐角圓筒的尺寸,公差和標識 |
(Textile machinery and accessories - Cones for cross winding - Part 2: Dimensions, tolerances and designation of cones with half angle 3 30 (ISO 8489-2:1995)) |
| DIN ISO 8489-3-1997 |
紡織機械和附件.圓錐形圓筒.第3部分:帶4°20＇半錐角圓筒的尺寸,公差和標識 |
(Textile machinery and accessories - Cones for cross winding - Part 3: Dimensions, tolerances and designation of cones with half angle 4 20 (ISO 8489-3:1995)) |
| DIN ISO 8489-4-1997 |
紡織機械和附件.圓錐形圓筒.第4部分:印染用帶4°20＇半錐角圓筒的尺寸,公差和標識 |
(Textile machinery and accessories - Cones for cross winding - Part 4: Dimensions, tolerances and designation of cones with half angle 4 20 for winding for dyeing purposes (ISO 8489-4:1995)) |
| DIN ISO 8489-5-1997 |
紡織機械和附件.圓錐形圓筒.第5部分:帶5°57＇半錐角圓筒的尺寸,公差和標識 |
(Textile machinery and accessories - Cones for cross winding - Part 5: Dimensions, tolerances and designation of cones with half angle 5 57 (ISO 8489-5:1995)) |
| DIN ISO 8524-1992 |
農用機械和拖拉機.播撒顆粒狀殺蟲劑或除草劑的設備.檢驗方法 |
(Agricultural machinery and tractors; equipment for distributing granulated crop protection products; test method; identical with ISO 8524:1986) |
| DIN ISO 8528-1-1997 |
往復式內燃機驅動的交流發電機組.第1部分:使用,額定功率和性能 |
(Reciprocating internal combustion engine driven alternating current generating sets - Part 1: Application, ratings and performance (ISO 8528-1:1993)) |
| DIN ISO 8528-2-1997 |
往復式內燃機驅動的交流發電機組.第2部分:發動機 |
(Reciprocating internal combustion engine driven alternating current generating sets - Part 2: Engines (ISO 8528-2:1993)) |
| DIN ISO 8528-3-1997 |
往復式內燃機驅動的交流發電機組.第3部分:機組交流發電機 |
(Reciprocating internal combustion engine driven alternating current generating sets - Part 3: Alternating current generators for generating sets (ISO 8528-3:1993)) |
| DIN ISO 8528-4-1997 |
往復式內燃機驅動的交流發電機組.第4部分:控制裝置和開關裝置 |
(Reciprocating internal combustion engine driven alternating current generating sets - Part 4: Control and switchgear (ISO 8528-4:1993)) |
| DIN ISO 8528-5-1997 |
往復式內燃機驅動的交流發電機組.第5部分:發電機組 |
(Reciprocating internal combustion engine driven alternating current generating sets - Part 5: Generating sets (ISO 8528-5:1993)) |
| DIN ISO 8528-6-1997 |
往復式內燃機驅動的交流發電機組.第6部分:試驗方法 |
(Reciprocating internal combustion engine driven alternating current generating sets - Part 6: Test methods (ISO 8528-6:1993)) |
| DIN ISO 8528-7-1997 |
往復式內燃機驅動的交流發電機組.第7部分:規范和設計的技術報告 |
(Reciprocating internal combustion engine driven alternating current generating sets - Part 7: Technical declarations for specification and design (ISO 8528-7:1994)) |
| DIN ISO 8528-9-1999 |
往復式內燃機驅動的交流發電機組.第9部分:機械振動的測量和評定 |
(Reciprocating internal combustion engines driven alternating current generating sets - Part 9: Measurement and evaluation of mechanical vibrations (ISO 8528-9:1995)) |
| DIN ISO 8535-1-1995 |
壓燃式發動機.高壓噴射燃油管用的鋼管.第1部分:無縫冷拔單壁鋼管的要求 |
(Compression-ignition engines - Steel tubes for high-pressure fuel injection pipes - Part 1: Requirements for seamless cold-drawn single-wall tubes (ISO 8535-1:1990 + AMD 1:1993)) |
| DIN ISO 8536-1-2001 |
醫用輸液設備.第1部分:輸液玻璃瓶 |
(Infusion equipment for medical use - Part 1: Infusion glass bottles (ISO 8536-1:2000)) |
| DIN ISO 8536-3-2001 |
醫用輸液設備.第3部分:輸液瓶鋁帽 |
(Infusion equipment for medical use - Part 3: Aluminium caps for infusion bottles (ISO 8536-3:1999)) |
| DIN ISO 8536-6-1996 |
醫用輸液設備.第6部分:輸液瓶的冷凍干燥瓶 |
(Infusion equipment for medical use - Part 6: Freeze drying closures for infusion bottles (ISO 8536-6:1995)) |
| DIN ISO 8536-7-2001 |
醫用輸液設備.第7部分:輸液小瓶用鋁塑合成材料制帽蓋 |
(Infusion equipment for medical use - Part 7: Caps made of aluminium-plastics combinations for infusion bottles (ISO 8536-7:1999)) |
| DIN ISO 8560-1989 |
技術制圖.建筑制圖.模數尺寸管線和柵架的表示法 |
(Construction drawings; representation of modular sizes, lines and grids; identical with ISO 8560:1986) |
| DIN ISO 857-1-2002 |
焊接和相關工藝.詞匯.第1部分:金屬焊接工藝 |
(Welding and allied processes - Vocabulary - Part 1: Metal welding processes (ISO 857-1:1998)) |
| DIN ISO 8573-1-1995 |
一般用途壓縮空氣.第1部件:雜志和質量等級 |
(Compressed air for general use - Part 1: Contaminants and quality classes; identical with ISO 8573-1:1991) |
| DIN ISO 8575-1998 |
航空和航天.流體系統.液壓系統管道 |
(Aerospace - Fluid systems - Hydraulic system tubing (ISO 8575:1990)) |
| DIN ISO 8576-2002 |
光和光學儀器.顯微鏡.偏振光顯微鏡系統 |
(Optics and optical instruments - Microscopes - Reference system of polarized light microscopy (ISO 8576:1996)) |
| DIN ISO 8577-2001 |
光學和光學儀器.顯微鏡.濾光鏡 |
(Optics and optical instruments - Microscopes - Spectral filters (ISO 8577:1997)) |
| DIN ISO 8578-2003 |
光學和光學儀器.顯微鏡.物鏡和目鏡的標記 |
(Optics and optical instruments - Microscopes - Marking of objectives and eyepieces (ISO 8578:1997 + ISO 8578:1997/Cor. 1:2002)) |
| DIN ISO 8583-1988 |
銀行原始電報卡.互換電報說明.金融交易內涵 |
(Bank card originated messages; interchange message specifications; content for financial transactions; identical with ISO 8583:1987) |
| DIN ISO 8600-1-2000 |
光學和光學儀器.醫用內窺鏡和內窺鏡附件.第1部分:一般要求 |
(Optics and optical instruments - Medical endoscopes and endoscopic accessories - Part 1: General requirements (ISO 8600-1:1997)) |
| DIN ISO 8600-3-2001 |
光學和光學儀器.醫用內窺鏡和內窺鏡附件.第3部分:視野測定和光學內窺鏡觀測方向的測定 |
(Optics and optical instruments - Medical endoscopes and endoscopic accessories - Part 3: Determination of field of view and direction of view of endoscopes with optics (ISO 8600-3:1997)) |
| DIN ISO 8600-3-2004 |
光學和光學儀器.醫用內窺鏡和內窺鏡附件.第3部分:光學內窺鏡觀察方向和觀察區域的測定 |
|
| DIN ISO 8600-4-2001 |
光學和光學儀器.醫用內窺鏡和內窺鏡附件.第4部分:插入部分最大寬度的測定 |
(Optics and optical instruments - Medical endoscopes and endoscopic accessories - Part 4: Determination of maximum width of insertion portion (ISO 8600-4:1997)) |
| DIN ISO 8613-1-1991 |
信息處理系統.文件處理和通訊.辦公文件體系結構和互換格式.第1部分:前言和一般原理 |
(Information processing systems; text and office systems; office document architecture (ODA) and interchange format; part 1: introduction and general principles; identical with ISO 8613-1:1989) |
| DIN ISO 8613-2-1991 |
信息處理系統.文件處理和通訊.辦公文件體系結構和互換格式.第2部分:文件結構 |
(Information processing systems; text and office systems; office document architecture (ODA) and interchange format; part 2: document structures; identical with ISO 8613-2:1989) |
| DIN ISO 8613-4-1991 |
信息處理系統.文件處理和通訊.辦公文件體系結構和互換格式.第4部分:文件提問檔 |
(Information processing; text and office systems; Office Document Architecture (ODA) and interchange format; part 4: document profile; identical with ISO 8613-4:1989) |
| DIN ISO 8614-1998 |
滑雪板裝配.詞匯 |
(Ski bindings - Vocabulary (ISO 8614:1997)) |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com