標準號 |
中文名稱 |
英文名稱 |
| DIN 47730-1983 |
絕緣電力電線.07RN橡膠護套軟線.尺寸.標記.重量和交貨方式 |
(Cables, wires and flexible cords for power installation - Rubber sheathed flexible cable 07RN - Dimensions, designation, weights and packaging-requirement) |
| DIN 47731-1985 |
絕緣電力電線.03VV和03VVH2聚氯乙烯軟線.尺寸.標記.重量和交貨方式 |
(Cables, wires and flexible cords for power installation - PVC-sheathed flexible cable 03VV and 03VVH2 - Dimensions, designation, weights and packaging-requirement) |
| DIN 47732-1986 |
絕緣電力電線.05VV和05VVH2型聚氯乙烯軟線 |
(Cables, wires and flexible cords for power installation - PVC-sheathed flexible cable 05VV and 05VVH2 - Dimensions, designation, weights and packaging-requirement) |
| DIN 47734-1986 |
絕緣電力電線.NSSHOU橡膠護套軟線.尺寸.標記.重量和交貨方式 |
(Cables, wires and flexible cords for power installation - Rubber sheathed flexible cable NSSH橴 - Dimensions, designation, weights and packaging-requirements) |
| DIN 478-1985 |
方頭帶肩螺釘 |
(Square head bolts with collar) |
| DIN 479-1985 |
方頭短圓柱端螺栓 |
(Square head bolts with short dog point) |
| DIN 4791-1985 |
加熱設備.燃燒室和發熱器之間的電插頭連接 |
(Electrical connectors between burner and heat generator) |
| DIN 4794-1-1980 |
帶或不帶熱交換器的固定式熱空氣發生器.一般要求和通風技術要求.檢驗 |
(Stationary fan-assisted air heaters, with and without interchange of heat; common requirements and conditions for ventilation, testing) |
| DIN 4794-2-1980 |
固定式熱空氣發生器.燃油熱空氣發生器.要求.檢驗 |
(Stationary fan-assisted air heaters; oil fired air heaters, requirements, testing) |
| DIN 4794-3-1980 |
固定式熱空氣發生器.帶熱交換器的燃氣熱空氣發生器.要求.檢驗 |
(Stationary fan-assisted air heaters; gas fired air heaters with interchange of heat, requirements, testing) |
| DIN 4794-5-1980 |
固定式熱空氣發生器.一般要求和安全技術要求.安裝.運行 |
(Stationary fan-assisted air heaters; generally and safety requirements, setting, working) |
| DIN 4795-1991 |
房屋煙囪用吸收空氣調節裝置.概念.安全技術要求.檢驗.標志 |
(Draft regulators for chimneys; concepts safety requirements, testing, marking) |
| DIN 4797-1986 |
取暖和房間通風技術.順流出口.流阻測定 |
(Heating technique and room ventilation technique; down stream outlets; determination of the flow resistance) |
| DIN 4799-1990 |
室內空調技術.操作間的通風系統.檢驗 |
(Heating, ventilation and air-conditioning; testing of air distributions systems serving operating theatres) |
| DIN 480-1985 |
方頭帶肩和凸圓形末端螺釘 |
(Square head bolts with collar and oval half dog point) |
| DIN 4800-1980 |
鋼制雙壁熱水器.有兩個固定底板.可直立或橫臥使用 |
(Double-wall water heaters with two fixed steel covers for vertical and horizontal application) |
| DIN 48004-1969 |
架空電力線用絕緣子.帶有內固定的針式絕緣子st.串聯電壓10-30KV |
(Insulators for overhead power lines; pin type insulators St, rated voltages 10 to 30 kV) |
| DIN 48006-1-2005 |
架空線用絕緣子.第1部分:帶有窩孔帽的長棒形絕緣子LP |
|
| DIN 48006-2-2005 |
架空線用絕緣子.第2部分:帶有叉槽帽的長棒形絕緣子LG |
|
| DIN 48006-3-1987 |
強電架空線用絕緣子.實心絕緣子VK |
(Insulators for overhead lines; solid-core (VK) insulators) |
| DIN 4801-1980 |
鋼制單壁熱水器.可擰下的罩 |
(Single-wall water heaters with cover to be unscrewed, of steel) |
| DIN 48016-1970 |
1000V以下架空電力線路針式絕緣子緊固用螺帽 |
(Screwed cap for mounting pin type insulators for overhead power lines up to 1000 V) |
| DIN 4802-1980 |
鋼制單壁熱水器.帶中間接管 |
(Single-wall water heaters with neck, of steel) |
| DIN 4803-1980 |
鋼制雙壁熱水器.帶可擰下的罩 |
(Double-wall water heaters with cover to be unscrewed, of steel) |
| DIN 48031-1952 |
電纜和電線用線盤 |
(Coils for cables and lines) |
| DIN 4804-1980 |
鋼制雙壁熱水器.帶中間接管 |
(Double-wall water heaters with neck, of steel) |
| DIN 48044-1959 |
架空電力線路.直絕緣子支柱 |
(Power current overhead lines; straight insulator spindles) |
| DIN 48045-1959 |
架空電力線路.鉤形絕緣子支柱 |
(Power current overhead lines; bent insulator spindles) |
| DIN 4805-1-1980 |
集中供熱設備中的熱水器加熱部件的接頭.電加熱部件 |
(Connections for heatingapparatus for electric water heaters in central heating systems) |
| DIN 4805-2-1980 |
集中供熱設備中的熱水器加熱部件的接頭.管道加熱部件 |
(Connections for heatingapparatus for water heaters in central heating systems) |
| DIN 48050-1-1963 |
架空電力線路.直絕緣子支柱.圓錐形 |
(Insulator pin, conical) |
| DIN 48050-2-1963 |
架空電力線路.直絕緣子支柱.圓柱形 |
(Insulator pin, cylindrical) |
| DIN 48051-1-1959 |
架空電力線路.鉤形絕緣子支柱.普通型式 |
(Power current overhead lines; bent insulator spindles, standard design) |
| DIN 48051-3-1964 |
架空電力線路.旋緊用鉤形絕緣子支柱 |
(Power overhead lines; bent insulator spindles for screwing) |
| DIN 48055-1-1971 |
架空通信線路用絕緣子支柱.直支柱 |
(Insulator spindles for telecommunication overheads-lines; straight spindles) |
| DIN 48055-2-1971 |
架空通信線路用絕緣子支柱.U型支柱 |
Insulator spindles for telecommunication overhead-lines; U-spindles |
| DIN 48055-3-1971 |
架空通信線路用絕緣子支柱.彎鉤型 |
(Insulator spindles for telecommunication overhead-lines; hook-shaped spindles) |
| DIN 48055-4-1971 |
架空通信線路用絕緣子支柱.凹槽 |
(Insulator spindles for telecommunication overhead-lines; notches) |
| DIN 48059-1978 |
雙端球形銷 |
(Twin-balled pins for overhead power lines) |
| DIN 48062-1-1990 |
架空電力線路絕緣子用窩形外帽 |
(Overhead lines; socket caps for insulators) |
| DIN 48062-2-1990 |
架空電力線路絕緣子用槽形帽 |
(Overhead lines; clevis caps for insulators) |
| DIN 48063-1-1978 |
彈簧銷.尺寸 |
(Split Pins; Dimensions) |
| DIN 48065-1-1980 |
U形弓用不帶保護器具的固定絕緣子的鐵腳圈 |
(Ball eyes without protective fitting attachment, for U-shaped straps, for overhead power lines) |
| DIN 48065-2-1980 |
U形弓用帶保護器具的固定的絕緣子鐵腳圈 |
(Ball eyes with protective fitting attachment, for U-shaped straps, for overhead power lines) |
| DIN 48065-3-1980 |
連接螺栓用不帶保護器具的固定的絕緣子鐵腳圈 |
(Ball eyes with protective fitting attachment, for connection bolts, for overhead power lines) |
| DIN 48066-1-1975 |
合頁.支承合頁 |
(Hinges; supporting hinges (for overhead power lines)) |
| DIN 48066-2-1975 |
合頁.拉緊合頁 |
(Hinges; strain hinges (for overheard power lines)) |
| DIN 48067-1-1982 |
無保護器具固定的環 |
(Socket eyes without arc horn fixing for overhead lines) |
| DIN 48067-2-1982 |
帶保護器具固定的環 |
(Socket eyes with arc horn fixing for overhead lines) |
| DIN 48068-1982 |
保護裝置的固定.連接尺寸 |
(Protective fitting attechment; for overhead lines, connection dimensions) |
| DIN 48069-1-1977 |
架空線用無保護緊固件的雙眼 |
(Double eyes without protective fitting attachment, for overhead power lines) |
| DIN 48069-2-1980 |
架空線用有保護緊固件的雙眼 |
(Double eyes with protective fitting, for overhead power lines) |
| DIN 4807-1-1991 |
膨脹箱.術語.法規.檢驗和標記 |
(Expansion vessels; terminology, relevant legal regulations; testing and marking) |
| DIN 4807-2-1991 |
膨脹箱.采暖設備用開式和閉式膨脹箱:計算.要求和檢驗 |
(Expansion vessels; open and closed expansion vessels used in thermic systems; calculation, requirements and test) |
| DIN 4807-3-1993 |
膨脹箱.彈性材料膜片.要求和檢驗 |
(Expansion vessels; elastomer membranes; requirements and testing) |
| DIN 4807-5-1997 |
飲用水裝置用帶薄膜的封閉式膨脹箱.要求,檢驗,設計和標記符號.DVGW的技術要求 |
(Expansion vessels - Part 5: Closed expansion vessels with membrane for drinking water installations; Requirements, test, design and designation; DVGW code of practice) |
| DIN 48070-1-1976 |
襯墊.三角型襯墊 |
(Triangular yokes for overhead power lines) |
| DIN 48070-2-1976 |
襯墊.梯形和矩形襯墊 |
(Triangular and rectangular yokes for overhead power lines) |
| DIN 48072-1-1962 |
電力架空線用鋁絞線和鋼芯鋁絞線的接線端子 |
(Line tapes for stranded aluminium conductors and ACSR) |
| DIN 48072-2-1962 |
電力架空線用銅線和銅索的接線端子 |
(Line tapes for stranded copper conductors and solid ones) |
| DIN 48073-1975 |
連接螺栓 |
(Connecting bolts for overhead power lines) |
| DIN 48074-1990 |
魚尾板和托叉板.連接尺寸 |
(Eyes and clevisses; connecting dimensions) |
| DIN 48075-1-1967 |
電力架空線用鋁絞線和鋼芯鋁絞線的電流接線柱 |
(Parallel groove clamps for aluminium stranded conductors and for aluminium conductors steel-reinforced for overhead power lines) |
| DIN 48075-2-1972 |
電力架空線用銅線和青銅的電流接線柱 |
(Parallel groove clamps for stranded conductors of copper and bronce, for overhead power lines) |
| DIN 48077-1-1987 |
架空線和配電設備.用配件.絕緣子.鏈和固定接地線用配件名稱 |
(Accessories for overhead lines and switchgear; terms of accessories for insulators, string insulators and earthwire connections) |
| DIN 48078-1-1985 |
架空線用與連接螺栓連結的叉型接片 |
(Clevis straps for overhead lines, for coupling to connecting bolts on the strap side) |
| DIN 48078-2-1985 |
架空線用與連接U型條連結的叉型接片 |
(Clevis straps for overhead lines, for coupling to U-bolts on the strap side) |
| DIN 48083-1-1985 |
生產導線接頭用的壓力機模具.公稱壓力15KN和60KN以下的機械壓力機.安裝尺寸 |
(Dies for presses for pressure connections; mechanical presses with a nominal compressive force up to 15 and up to 60 kN connecting; dimensions) |
| DIN 48083-3-1985 |
生產導線接頭用的壓力機模具.公稱壓力為300.450和1000KN以下的液壓力機.安裝尺寸 |
(Dies for presses for pressure connections; hydraulical presses with a nominal compressive force up to 300, up to 450 and up to 1000 kN connecting; dimensions) |
| DIN 48083-4-1985 |
生產導線接頭用的壓力機模具.六角形壓模尺寸 |
(Dies for presses for pressure connections; dimensions of the hexagon compression type) |
| DIN 48084-1-1973 |
額定零壓６０ＫＶ以上的開關設備用導線和端子.應用 |
(Conductors and connectors in substations with a nominal voltage of 60 kV and upwards; terms of referances) |
| DIN 48085-1-1985 |
銅絞線用抗拉壓接頭 |
(Full tension compression joints, for copper conductors, for overhead lines) |
| DIN 48085-2-1985 |
鋁絞線用抗拉壓接頭 |
(Full tension compression joints, for aluminium-conductors, for overhead lines) |
| DIN 48085-3-1985 |
鋁包鋼絞線用抗拉壓接頭 |
(Full tension compression joints, for ACSR-conductors, for overhead lines) |
| DIN 48087-1985 |
攜帶式儀器的接地和短接.軸桿連接部份 |
(Portable apparatus for earthing and short-circuiting; coupling part) |
| DIN 48088-1-1985 |
接地的接點和短路設備.球頭銷 |
(Connecting point for earthing and short-circuiting devices; ball pin) |
| DIN 48088-2-1985 |
接地的接點和短路設備.連接接地一邊帶環型槽圓柱形螺栓 |
(Connecting point for earthing and short-circuiting devices; cylinder bolt and annuar slot for earth-side connection) |
| DIN 48088-3-1985 |
接地的接點和短路設備.導線的卡箍固定點（鋼索管子） |
(Connecting point for earthing and short-circuiting devices; bracket fixing point for phase conductors) |
| DIN 48088-4-1985 |
接地的接點和短路設備.導線外殼的固定點（鋼索.管子） |
(Connecting point for earthing and short circuiting devices; shell fixing point for phase conductors) |
| DIN 48088-5-1985 |
接地的接點和短路設備.接地一邊的連接件 |
(Connecting point for earthing and short circuiting devices; connecting piece for earthing conductors) |
| DIN 4809-1-1986 |
彈性復合材料制水暖設備用膨脹件(橡膠膨脹件).最高工作溫度為100℃及最大操作壓力為10巴.要求和檢驗 |
(Compensators made of elstomeric compound materials (rubber-compensators) for warm water heating-plants; up to a maximum operating-temperature of 100 C and a maximum pressure of 10 bar) |
| DIN 4809-2-1986 |
彈性復合材料制水暖設備用膨脹件(橡膠膨脹件).構造和連接尺寸 |
(Compensators made of elastomeric compound materials (rubber-compensators) for warmwater-heating-plants; constructional and connecting sizes) |
| DIN 4810-1991 |
供水設備鋼制壓力容器 |
(Steel pressure vessels for water supply systems) |
| DIN 48108-1-1983 |
電工陶瓷制品.絕緣件緊固部位.滾花 |
(Ceramic components for electrical purposes; mounting places for insulators; grooving) |
| DIN 48108-2-1983 |
電工陶瓷制品.絕緣件緊固部位.上砂 |
(Ceramic components for electrical purposes; mounting places for insulators; sanded surfaces) |
| DIN 48108-3-1983 |
電工陶瓷制品.絕緣件緊固部位.皺紋面 |
(Ceramic components for electrical purposes; mounting places for insulators; undulatory profile) |
| DIN 48113-1973 |
電壓1KV以上開關設備和配電裝置用支柱絕緣子.彎曲強度定義的分類 |
(Post insulators for switchgears and substation with nominal voltages greater than 1000 V; co-ordination of the definitions for mechanical bending strength) |
| DIN 48115-1966 |
戶外絕緣子裙部.尺寸.爬電距離的測定 |
(Outdoor insulator sheds; dimensions, creepage distance calculation) |
| DIN 48124-1-1980 |
氫冷發電機用套管.自然冷卻套管 |
(Natural cooled bushings for hydrogen cooled generators) |
| DIN 48124-2-1980 |
氫冷發電機用套管.液體冷卻套管 |
(Liquid cooled bushings for hydrogen cooled generators) |
| DIN 48124-3-1980 |
氫冷發電機用套管.氣體冷卻套管 |
(Gas cooled bushings for hydrogen cooled generators) |
| DIN 48125-1966 |
戶內外連通設備穿墻套管.45N和45S至150N和150S系列.連接和緊固尺寸 |
(Outdoor/indoor wall bushings; insulation class 45N and 45S to 150N and 150S; mounting dimensions) |
| DIN 48127-1962 |
戶內外連通設備穿墻套管.10-30系列.主要尺寸和連接尺寸 |
(Wall bushings for use in open air, indoor plants; insulation class 3 to 30) |
| DIN 48128-1962 |
戶內外連通設備穿墻套管.10-30系列.普通結構 |
(Wall bushings for use in open-air, indoor plants; insulation rating 3 to 30) |
| DIN 48138-1982 |
針式絕緣子.連接尺寸 |
(Pin type insulators; dimensions for connection) |
| DIN 48139-1982 |
平板型針式絕緣子.連接尺寸 |
(Plate supported pin type insulators; dimensions of connection) |
| DIN 48140-1960 |
架空通信線路.絕緣子RMK |
(Insulators RMk) |
| DIN 48141-1962 |
架空通信線路.絕緣子RMd |
(Insulators RMd) |
| DIN 48145-1951 |
架空通信線路.絕緣子RMU |
(Overhead power lines for telecommunication; insulator RMue) |
| DIN 4815-2-1979 |
液化氣用軟管.軟管管道 |
(Hoses for LPG; hose assemblies) |
| DIN 4815-3-1985 |
液化氣用軟管.車輛容器裝入和排空用軟管管道 |
(Flexible tubes for LPG; flexible tubes for filling and emptying of transportation vehicles) |
| DIN 4815-4-1987 |
液化氣用軟管.車輛內動力氣體裝置軟管和軟管管道 |
(Hoses for LPG; hoses and hose assemblies for fuel gas installations in vehicles) |
| DIN 4815-5-1988 |
液化氣用軟管.車輛內液化氣管道用軟管接合器.概念.安全技術要求.檢驗.標記 |
(Hoses for LPG; coupling for LPG hose assemblies in vehicles; concepts safety requirements, tests, marking) |
| DIN 48150-1966 |
架空電力線.針式絕緣子N額定電壓1KV以下 |
(Pin type insulators N; rated voltage below 1 kV) |
| DIN 48152-1958 |
架空電力線.拉緊絕緣子N.額定電壓1000V以下 |
(Power current overhead lines; tension insulator Z, rated voltage below 1 kV) |
| DIN 48154-1-1959 |
架空電力線.蝶式絕緣子S.絕緣子 |
(Power current overhead lines; shackle insulators S, insulator bodies) |
| DIN 48154-2-1959 |
架空電力線.蝶式絕緣子S.弓形架 |
(Power current overhead lines; shackle insulators S, bows) |
| DIN 48156-1959 |
架空電力線.絕緣子E.額定電壓1000V以下 |
(Power current overhead lines; egg-shaped insulator E, rated voltage below 1 kV) |
| DIN 48156-2-1963 |
架空電力線.拉緊緣子E.額定電壓1000V以下.弓形架 |
(Egg-shaped insulator, anchoring bracket) |
| DIN 4817-1-1981 |
液態氣的截止閥.概念.安全技術要求.檢驗.標志 |
(Shut off valves for liquefied gases; definitions, requirement, testing, marking) |
| DIN 48170-1986 |
額定電壓1000V以下架空電力線路用屋頂支柱.裝配.零件 |
(Roof poles for overhead power lines up to 1000 V; combination, components) |
| DIN 48172-1963 |
架空電力線.額定電壓1KV以下.屋頂引入管線的端部.裝配.零件 |
(Inlet head of roof support; assembly drawing, parts) |
| DIN 48173-1959 |
額定電壓1000V以下架空電力線路用屋頂拉桿.裝配.零件 |
(Power current overhead lines, rated voltage below 1 kV; roof anchorage, compilation, piece parts) |
| DIN 48174-1-1984 |
額定電壓1KV以下架空電力線路木質電線桿的橫擔木 |
(Crossarms for wooden poles for overhead power lines up to 1000 V) |
| DIN 48174-2-1984 |
額定電壓1KV以下架空電力線路屋頂架線桿的橫擔木 |
(Crossarms for roof poles for overhead power lines up to 1000 V) |
| DIN 48174-3-1984 |
額定電壓1KV以下架空電力線路木質電線桿和屋頂架線桿的橫梁 |
(Crossarms for wooden poles and roof poles for overhead power lines up to 1000 V) |
| DIN 48175-1-1978 |
額定電壓1000V以下架空電力線帶支架的用戶屋頂引入線.標準結構.防護類型IP40 |
(Roof poles for lead-in cables, type N, degree of protection IP 40, for overhead power lines up to 1000 V) |
| DIN 48175-2-1978 |
額定電壓1000V以下架空電力線帶支架的用戶屋頂引入線.特殊結構.防護類型IP54 |
(Roof poles for lead-in cables, type S, degree of protection IP 54, for overhead power lines up to 1000 V) |
| DIN 48176-1963 |
架空電力線路用屋頂架線桿斜支柱.裝配.零件 |
(Roof pole brace for overhead lines) |
| DIN 482-2002 |
天然石料造的街道路邊石 |
(Natural stone kerbs) |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com