標準號 |
中文名稱 |
英文名稱 |
| ASTM C 1240-2001 |
水硬水泥混凝土、灰漿和薄漿中作為礦物添加劑的硅酸氣體使用的標準規范 |
Standard Specification for Use of Silica Fume for Use as a Mineral Admixture in Hydraulic-Cement Concrete, Mortar, and Grout |
| ASTM C 1241-2000 |
凝固過程中膠乳密封劑體積收縮的標準試驗方法 |
Standard Test Method for Volume Shrinkage of Latex Sealants During Cure |
| ASTM C 1242-2001 |
石錨和錨固系統的設計、選擇和安裝標準指南 |
Standard Guide for Design, Selection, and Installation of Stone Anchors and Anchoring Systems |
| ASTM C 1243-1993 |
使用轉盤的無釉陶瓷磚相對深層耐磨性的標準試驗方法 |
Standard Test Method for Relative Resistance to Deep Abrasive Wear of Unglazed Ceramic Tile by Rotating Disc |
| ASTM C 1244-1993 |
負壓(真空)試驗測定混凝土污水管人孔的試驗方法 |
Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test |
| ASTM C 1244M-1993 |
負壓(真空)試驗測定混凝土污水管人孔的試驗方法(米制) |
Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test (Metric) |
| ASTM C 1245-1993 |
測定路碾水硬性壓縮混凝土與其它水硬性水泥混合物結合強度的標準試驗方法-點負荷試驗 |
Standard Test Method for Determining Bond Strength Between Hardened Roller Compacted Concrete and Other Hardened Cementitious Mixtures Point Load Test |
| ASTM C 1246-1999 |
彈性體密封劑凝固后熱老化對重量損失、裂開和粉化影響的標準試驗方法 |
Standard Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants After Cure |
| ASTM C 1247-1998 |
連續浸液的密封劑壽命標準試驗方法 |
Standard Test Method for Durability of Sealants Exposed to Continuous Immersion in Liquids |
| ASTM C 1248-1993 |
用連接密封層時多孔襯底染色的標準試驗方法 |
Standard Test Method for Staining of Porous Substrate by Joint Sealants |
| ASTM C 1249-1993 |
構造密封玻璃窗用封閉絕緣玻璃構件的二級封閉標準指南 |
Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications |
| ASTM C 125-1999 |
與混凝土和混凝土集料相關的標準術語 |
Standard Terminology Relating to Concrete and Concrete Aggregates |
| ASTM C 1250-1993 |
用冷卻液的彈性防水膜的不揮發含量的標準試驗方法 |
Standard Test Method for Nonvolatile Content of Cold Liquid-Applied Elastomeric Waterproofing Membranes |
| ASTM C 1251-1995 |
用氣體吸收法測定高級陶瓷材料的表面面積比 |
Standard Guide for Determination of Specific Surface Area of Advanced Ceramic Materials by Gas Adsorption |
| ASTM C 1252-1998 |
細集料中未壓實的空隙率的標準試驗方法(受顆粒形狀,表面狀態和粒度的影響) |
Standard Test Methods for Uncompacted Void Content of Fine Aggregate (as Influenced by Particle Shape, Surface Texture, and Grading) |
| ASTM C 1253-1993 |
測定密封層背襯除氣能力的標準試驗方法 |
Standard Test Method for Determining the Outgassing Potential of Sealant Backing |
| ASTM C 1254-1999 |
用X射線熒光法測定無機酸中鈾的標準試驗法 |
Standard Test Method for Determination of Uranium in Mineral Acids by X-Ray Fluorescence |
| ASTM C 1255-1993 |
用能量色散X射線熒光光譜法分析土壤中鈾和釷的標準試驗方法 |
Standard Test Method for Analysis of Uranium and Thorium in Soils by Energy Dispersive X-Ray Fluorescence Spectroscopy |
| ASTM C 1256-1993 |
說明玻璃破裂表面特性的標準規范 |
Standard Practice for Interpreting Glass Fracture Surface Features |
| ASTM C 1257-1994 |
溶劑釋放型密封劑加速老化的標準試驗方法 |
Standard Test Method for Accelerated Weathering of Solvent-Release-Type Sealants |
| ASTM C 1258-1994 |
隔熱用蒸汽緩凝劑耐高溫和耐濕度性能標準試驗方法 |
Standard Test Method for Elevated Temperature and Humidity Resistance of Vapor Retarders for Insulation |
| ASTM C 1259-2001 |
用振動脈沖激勵法的高級陶瓷動態楊氏模量、剪切模量和泊松比的標準試驗方法 |
Standard Test Method for Dynamic Youngs Modulus, Shear Modulus, and Poissons Ratio for Advanced Ceramics by Impulse Excitation of Vibration |
| ASTM C 126-1999 |
上釉陶瓷結構粘土面磚、飾面瓷磚和實心砌塊標準規范 |
Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units |
| ASTM C 1260-1994 |
集料的堿潛在反應性的標準試驗方法.膠泥棒法1 |
Standard Test Method for Potential Alkali Reactivity of Aggregates (Mortar-Bar Method)1 |
| ASTM C 1261-1998 |
住宅壁爐用火箱磚的標準規范 |
Standard Specification for Firebox Brick for Residential Fireplaces |
| ASTM C 1262-1998 |
評定制造混凝土磚石構件和有關混凝土構件冷凍和解凍壽命的標準試驗方法 |
Standard Test Method for Evaluating the Freeze-Thaw Durability of Manufactured Concrete Masonry Units and Related Concrete Units |
| ASTM C 1263-1995 |
撓性水蒸汽緩凝劑熱完整性標準試驗方法 |
Standard Test Method for Thermal Integrity of Flexible Water Vapor Retarders |
| ASTM C 1264/C 1264M-1995 |
石膏板抽樣,檢驗,剔除,認證,包裝,標記,發運,裝卸和儲存標準規范 |
Standard Specification for Sampling, Inspection, Rejection, Certification, Packaging, Marking, Shipping, Handling, and Storage of Gypsum Board |
| ASTM C 1265-1994 |
鑲嵌玻璃時對隔熱玻璃邊緣密封劑的抗拉性能的標準試驗方法 |
Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications |
| ASTM C 1266-1995 |
預制膠帶密封劑流動特性標準試驗方法 |
Standard Test Method for Flow Characteristics of Preformed Tape Sealants |
| ASTM C 1267-1994 |
使用鐵II在磷酸中還原后在有釩的情況下滴鉻(VI)的鈾標準試驗方法 |
Standard Test Method for Uranium by Iron (II) Reduction in Phosphoric Acid Followed by Chromium (VI) Titration in the Presence of Vanadium |
| ASTM C 1268-1994 |
用γ射線光譜法定量測定钚中镅241的標準試驗方法 |
Standard Test Method for Quantitative Determination of Americium 241 in Plutonium by Gamma-Ray Spectrometry |
| ASTM C 1269-1997 |
內置穿過式金屬探測器操作靈敏度設置調整的標準規程 |
Standard Practice for Adjusting the Operational Sensitivity Setting of In-Plant Walk-Through Metal Detectors |
| ASTM C 127-2001 |
粗集料的密度、比重和吸收性的標準試驗方法 |
Standard Test Method for Density, Relative Density (Specific Gravity), and Absorption of Coarse Aggregate |
| ASTM C 1270-1997 |
內置穿過式金屬探測器探測靈敏度標志的標準實用規程 |
Standard Practice for Detection Sensitivity Mapping of In-Plant Walk-Through Metal Detectors |
| ASTM C 1271-1999 |
石灰和石灰?guī)rX射線光譜分析標準試驗方法 |
Standard Test Method for X-ray Spectrometric Analysis of Lime and Limestone |
| ASTM C 1272-2000 |
重型車輛通過的路面磚標準規范 |
Standard Specification for Heavy Vehicular Paving Brick |
| ASTM C 1273-1995 |
環境溫度下單片高級陶瓷抗拉強度標準規程 |
Standard Practice for Tensile Strength of Monolithic Advanced Ceramics at Ambient Temperatures |
| ASTM C 1274-1995 |
用物理吸收法對高級陶瓷比表面積的標準試驗方法 |
Standard Test Method for Advanced Ceramic Specific Surface Area by Physical Adsorption |
| ASTM C 1275-2000 |
室溫下用矩形截面整體試樣對連續纖維增強高級陶瓷作單片抗拉強度試驗的標準試驗方法 |
Standard Test Method for Monotonic Tensile Behavior of Continuous Fiber-Reinforced Advanced Ceramics with Solid Rectangular Cross-Section Specimens at Ambient Temperatures |
| ASTM C 1276-1994 |
利用旋轉米度計測量模制粉末熔點以上粘度的標準試驗方法 |
Standard Test Method for Measuring the Viscosity of Mold Powders Above Their Melting Point Using a Rotational Viscometer |
| ASTM C 1277-1997 |
防護聯接器連接無轂鑄鐵污水管和配件標準規范 |
Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings |
| ASTM C 1278/C 1278M-2001 |
纖維增強石膏鑲板標準規范 |
Standard Specification for Fiber-Reinforced Gypsum Panel |
| ASTM C 1279-1994 |
在退火、熱強固和全回火平面玻璃中邊緣和表面應力非破壞性光彈測量的標準試驗方法 |
Standard Test Method for Non-Destructive Photoelastic Measurement of Edge and Surface Stresses in Annealed, Heat-Strengthened, and Fully Tempered Flat Glass |
| ASTM C 128-2001 |
細集料的密度、比重和吸收性的標準試驗方法 |
Standard Test Method for Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate |
| ASTM C 1280-1998 |
石膏包覆板裝配的標準規范 |
Standard Specification for Application of Gypsum Sheathing |
| ASTM C 1281-1999 |
鑲嵌玻璃用預制密封條的標準規范 |
Standard Specification for Preformed Tape Sealants for Glazing Applications |
| ASTM C 1282-1994 |
用離心光電沉淀法測定高級陶瓷粒徑分布的標準試驗方法 |
Standard Test Method for Determining the Particle Size Distribution of Advanced Ceramics by Centrifugal Photosedimentation |
| ASTM C 1283-1999 |
安裝粘土煙道襯塊的標準操作規范 |
Standard Practice for Installing Clay Flue Lining |
| ASTM C 1284-1994 |
用α光譜測定法電鍍錒素的標準規程 |
Standard Practice for Electrodeposition of the Actinides for Alpha Spectrometry |
| ASTM C 1285-1997 |
確定核廢物和混合廢棄玻璃耐化學性能的標準試驗方法:產品一致性試驗(PCT) |
Standard Test Methods for Determining Chemical Durability of Nuclear, Hazardous, and Mixed Waste Glasses: The Product Consistency Test (PCT) |
| ASTM C 1286-1994 |
高級陶磁的標準分類 |
Standard Classification for Advanced Ceramics |
| ASTM C 1287-1995 |
用誘導數個等離子體物質光譜測定法對二氧化鈾中混雜物的標準測定方法 |
Standard Test Method for Determination of Impurities in Uranium Dioxide by Inductively Coupled Plasma Mass Spectrometry |
| ASTM C 1288-1996 |
單塊非石棉纖維水泥內襯底薄板的標準規范 |
Standard Specification for Discrete Non-Asbestos Fiber-Cement Interior Substrate Sheets |
| ASTM C 1289-2001 |
貼面硬質泡沫聚異氰尿酸酯隔熱板的標準規范 |
Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board |
| ASTM C 129-2001 |
非承重混凝土砌塊的標準規范 |
Standard Specification for Nonloadbearing Concrete Masonry Units |
| ASTM C 1290-1995 |
外部隔熱HVAC導管用的軟玻璃纖維地毯隔熱材料的標準規范 |
Standard Specification for Flexible Fibrous Glass Blanket Insulation Used to Externally Insulate HVAC Ducts |
| ASTM C 1291-2000 |
高級單片陶瓷的高溫抗拉蠕變應變、蠕變應變率及蠕變斷裂時間的標準試驗方法 |
Standard Test Method for Elevated Temperature Tensile Creep Strain, Creep Strain Rate, and Creep Time-to-Failure for Advanced Monolithic Ceramics |
| ASTM C 1292-2000 |
室溫下連續纖維增強高級陶瓷剪切強度的標準試驗方法 |
Standard Test Method for Shear Strength of Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperatures |
| ASTM C 1293-2001 |
由于堿-硅石反應引起的混凝土長度變化測定的標準試驗方法 |
Standard Test Method for Determination of Length Change of Concrete Due to Alkali-Silica Reaction |
| ASTM C 1294-2001 |
絕緣玻璃密封條與液體外加玻璃材料的混用性的標準試驗方法 |
Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials |
| ASTM C 1295-1998 |
六氟化鈾裂變產物釋放的γ射線能量發射的標準試驗方法 |
Standard Test Method for Gamma Energy Emission from Fission Products in Uranium Hexafluoride |
| ASTM C 1296-1995 |
X射線熒光(XRF)測定氧化鈾和硝酸酰溶液中硫的標準試驗方法 |
Standard Test Method for Determination of Sulfur in Uranium Oxides and Uranyl Nitrate Solutions by X-Ray Fluorescence (XRF) |
| ASTM C 1297-1995 |
核燃料循環材料分析用實驗室的定量分析法的標準導則 |
Standard Guide for Qualification of Laboratory Analysts for the Analysis of Nuclear Fuel Cycle Materials |
| ASTM C 1298-1995 |
工業煙囪磚內襯設計與設計標準導則 |
Standard Guide for the Design and Construction of Brick Liners for Industrial Chimneys |
| ASTM C 1299-1999 |
液體密封劑選用的標準導則 |
Standard Guide for Use in Selection of Liquid-Applied Sealants |
| ASTM C 1300-1995 |
用干涉法測定玻璃原料和衛生陶瓷材料線性熱膨脹的標準試驗方法 |
Standard Test Method for Linear Thermal Expansion of Glaze Frits and Ceramic Whiteware Materials by the Interferometric Method |
| ASTM C 1301-1995 |
用感應耦合等離子體原子發射光譜法(ICP)和原子吸收法(AA)測定石灰?guī)r和石灰中常量素和痕量素的標準試驗方法 |
Standard Test Method for Major and Trace Elements in Limestone and Lime by Inductively Coupled Plasma-Atomic Emission Spectroscopy (ICP) and Atomic Absorption (AA) |
| ASTM C 1302-1995 |
隔熱試驗方法及標準的關鍵詞選擇和使用標準導則 |
Standard Guide for Selection and Use of Keywords for Thermal Insulation Test Methods and Standards |
| ASTM C 1303-2000 |
受控實驗室條件下用限幅和定標法評定無面剛性閉室塑料泡沫的熱阻抗長期變化的標準試驗方法 |
Standard Test Method for Estimating the Long-Term Change in the Thermal Resistance of Unfaced Rigid Closed Cell Plastic Foams by Slicing and Scaling Under Controlled Laboratory Conditions |
| ASTM C 1304-1995 |
隔熱材料散發氣味評定的標準試驗方法 |
Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials |
| ASTM C 1305-2000 |
防液體薄膜裂紋遮蔽能力的標準試驗方法 |
Standard Test Method for Crack Bridging Ability of Liquid-Applied Waterproofing Membrane |
| ASTM C 1306-2000 |
防液體薄膜抗液體靜壓力的標準試驗方法 |
Standard Test Method for Hydrostatic Pressure Resistance of a Liquid-Applied Waterproofing Membrane |
| ASTM C 1307-1995 |
用(III)钚數組分光光度法鑒定钚的標準測試方法 |
Standard Test Method for Plutonium Assay by Plutonium (III)e Array Spectrophotometry |
| ASTM C 1308-1995 |
固化廢料中擴散釋放物加速浸出試驗,模型擴散的計算機程序和從圓柱形廢料狀態中分離淋濾的標準試驗方法 |
Standard Test Method for Accelerated Leach Test for Diffusive Releases from Solidified Waste and a Computer Program to Model Diffusive, Fractional Leaching from Cylindrical Waste Forms |
| ASTM C 1309-1997 |
內置穿過式金屬檢測器的性能評定規程 |
Standard Practice for Performance Evaluation of In-Plant Walk-Through Metal Detectors |
| ASTM C 131-2001 |
UNS NO8120、UNS NO8800、UNS NO8810和UNS NO8811焊接合金管的標準規范 |
Standard Specification for Welded UNS N08120, UNS N08800, UNS N08810, and UNS N08811 Alloy Tubes |
| ASTM C 1310-2001 |
使用流體噴射預集中的感應耦合等離子體質譜測量法測定土壤中放射性核素的標準試驗方法 |
Standard Test Method for Determining Radionuclides in Soils by Inductively Coupled Plasma-Mass Spectrometry Using Flow Injection Preconcentration |
| ASTM C 1311-1995 |
斷開密封層溶劑的標準規范 |
Standard Specification for Solvent Release Sealants |
| ASTM C 1312-1997 |
實驗室中耐化學性硫聚合水泥固結試驗樣品制作和調合的標準規程 |
Standard Practice for Making and Conditioning Chemical-Resistant Sulfur Polymer Cement Concrete Test Specimens in the Laboratory |
| ASTM C 1313-1997 |
房屋建筑用片狀輻射柵欄的標準規范 |
Standard Specification for Sheet Radiant Barriers for Building Construction Applications |
| ASTM C 1314-2000 |
砌磚棱柱的壓縮強度的標準試驗方法 |
Standard Test Method for Compressive Strength of Masonry Prisms |
| ASTM C 1315-2000 |
固化混凝土和密封混凝土用有特殊性能的液體成膜化合物的標準規范 |
Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete |
| ASTM C 1316-2001 |
使用a252Cf的被動-主動中子計數法在碎片和廢料中作核材料無損檢定的標準試驗方法 |
Standard Test Method for Nondestructive Assay of Nuclear Material in Scrap and Waste by Passive-Active Neutron Counting Using a 252 Cf Shuffler |
| ASTM C 1317-1995 |
硅酸鹽或耐酸的基體樣品溶解的標準操作規程 |
Standard Practice for Dissolution of Silicate or Acid-Resistant Matrix Samples |
| ASTM C 1318-1995 |
煙道氣體脫硫用石灰中的可溶解鈣、氧化鎂總中合能力的標準測定方法 |
Standard Test Method for Determination of Total Neutralizing Capability and Dissolved Calcium and Magnesium Oxide in Lime for Flue Gas Desulfurization (FGD) |
| ASTM C 1319-2001 |
混凝土格子鋪設裝置的標準規范 |
Standard Specification for Concrete Grid Paving Units |
| ASTM C 1320-1995 |
輕型結構用礦物纖維隔熱毯的安裝規程 |
Standard Practice for Installation of Mineral Fiber Batt and Blanket Thermal Insulation for Light Frame Construction |
| ASTM C 1321-1998 |
建筑物內部輻射控制涂層系統的安裝和使用的標準規程 |
Standard Practice for Installation and Use of Interior Radiation Control Coating Systems (IRCCS) in Building Construction |
| ASTM C 1322-1996 |
高級陶瓷中斷裂點的斷口組織檢查和特性的標準規程 |
Standard Practice for Fractography and Characterization of Fracture Origins in Advanced Ceramics |
| ASTM C 1323-1996 |
環境溫度下徑向壓縮C環樣品的高級陶瓷的極限強度的測試方法 |
Standard Test Method for Ultimate Strength of Advanced Ceramics with Diametrally Compressed C-Ring Specimens at Ambient Temperature |
| ASTM C 1324-1996 |
硬砌磚灰漿的檢測和分析的標準試驗方法 |
Standard Test Method for Examination and Analysis of Hardened Masonry Mortar |
| ASTM C 1325-1999 |
纖維氈增強的無石棉水泥內襯薄板的標準規范 |
Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cement Interior Substrate Sheets |
| ASTM C 1326-1999 |
高級陶瓷的努譜壓痕硬度的標準試驗方法 |
Standard Test Method for Knoop Indentation Hardness of Advanced Ceramics |
| ASTM C 1327-1999 |
高級陶瓷的維氏壓痕硬度的標準試驗方法 |
Standard Test Method for Vickers Indentation Hardness of Advanced Ceramics |
| ASTM C 1328-1998 |
塑性(優質細灰泥)水泥的標準規范 |
Standard Specification for Plastic (Stucco) Cement |
| ASTM C 1329-1998 |
砂漿水泥的標準規范 |
Standard Specification for Mortar Cement |
| ASTM C 133-1997 |
耐火磚及異型磚的冷破碎強度和撓折模量的試驗方法 |
Test Methods for Cold Crushing Strength and Modulus of Rupture of Refractory Brick and Shapes |
| ASTM C 1330-1996 |
與冷卻液密封膠一起使用的圓柱形密封膠襯標準規范 |
Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid Applied Sealants |
| ASTM C 1331-2001 |
用寬帶脈沖反射交互作用法測量高級陶瓷中超聲速率的標準試驗方法 |
Standard Test Method for Measuring Ultrasonic Velocity in Advanced Ceramics with Broadband Pulse-Echo Cross-Correlation Method |
| ASTM C 1332-2001 |
用脈沖反射接觸技術測量高級陶瓷超聲衰減系數的標準試驗方法 |
Standard Test Method for Measurement of Ultrasonic Attenuation Coefficients of Advanced Ceramics by Pulse-Echo Contact Technique |
| ASTM C 1334-1996 |
轉換到核純級二氧化鈾之前分解用含5%以下235U的氧化鈾的標準規范 |
Standard Specification for Uranium Oxides with a 235 U Content of Less Than 5% for Dissolution Prior to Conversion to Nuclear-Grade Uranium Dioxide |
| ASTM C 1335-1996 |
人造巖石和火山灰?guī)r礦物纖維隔熱材料的非纖維質含量測量用的標準試驗方法 |
Standard Test Method for Measuring Non-Fibrous Content of Man-Made Rock and Slag Mineral Fiber Insulation |
| ASTM C 1336-1996 |
夾雜滲渣的纖維非氧化陶瓷增強樣品的標準操作 |
Standard Practice for Fabricating Non-Oxide Ceramic Reference Specimens Containing Seeded Inclusions |
| ASTM C 1337-1996 |
高溫抗拉載荷下連續纖維增強陶瓷合成物的蠕變和蠕變斷裂的標準試驗方法 |
Standard Test Method for Creep and Creep Rupture of Continuous Fiber-Reinforced Ceramic Composites under Tensile Loading at Elevated Temperatures |
| ASTM C 1338-1996 |
測量隔熱材料和飾面耐霉性的標準試驗方法 |
Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM C 1339-1996 |
抗化學腐蝕聚合物機械薄漿的可流動性和乘重區的標準試驗方法 |
Standard Test Method for Flowability and Bearing Area of Chemical-Resistant Polymer Machinery Grouts |
| ASTM C 134-1995 |
耐火磚和絕熱耐火磚的尺寸和松裝密度的試驗方法 |
Test Methods for Size and Bulk Density of Refractory Brick and Insulating Firebrick |
| ASTM C 1341-2000 |
連續纖維增強高級陶瓷合成物彎曲特性的標準試驗方法 |
Standard Test Method for Flexural Properties of Continuous Fiber-Reinforced Advanced Ceramic Composites |
| ASTM C 1342-1996 |
通量熔融樣品分部的標準規程 |
Standard Practice for Flux Fusion Sample Distribution |
| ASTM C 1343-1996 |
用X線熒光測定油和有機溶液中鈾的底濃度的標準試驗方法 |
Standard Test Method for Determination of Low Concentrations of Uranium in Oils and Organic Liquids by X-ray Fluorescence |
| ASTM C 1344-1997 |
用標準氣體源質譜法進行六氟化鈾的同位分析的標準試驗方法 |
Standard Test Method for Isotopic Analysis of Uranium Hexafluoride by Single-Standard Gas Source Mass Spectrometer Method |
| ASTM C 1345-1996 |
通過感應耦合等離子體度譜數對土壤中總的和同位素鈾及總釷分析的標準試驗方法 |
Standard Test Method for Analysis of Total and Isotopic Uranium and Total Thorium in Soils by Inductively Coupled Plasma-Mass Spectrometry |
| ASTM C 1346-1996 |
P-10管中UF 6溶解的標準規程 |
Standard Practice for Dissolution of UF 6 from P-10 Tubes |
| ASTM C 1347-1996 |
分析用鈾材料的制備和分離的標準規程 |
Standard Practice for Preparation and Dissolution of Uranium Materials for Analysis |
| ASTM C 1348-2001 |
直接加氫還原成核級二氧化鈾的U-235含量低于5%的混合氧化鈾的標準規范 |
Standard Specification for Blended Uranium Oxides with a 235U Content of Less Than 5 % for Direct Hydrogen Reduction to Nuclear Grade Uranium Dioxide |
| ASTM C 1349-1996 |
聚碳酸酯鍍層建筑用平板玻璃的標準規范 |
Standard Specification for Architectural Flat Glass Clad Polycarbonate |
| ASTM C 135-1996 |
用水浸法測定耐火材料的準確比重的試驗方法 |
Test Method for True Specific Gravity of Refractory Materials by Water Immersion |
| ASTM C 1350M-1996 |
在軟化點和退火范圍(大約108巴(點)到大約10巴)之間玻璃和黏滯度測定的標準試驗方法 |
Standard Test Method for Measurement of Viscosity of Glass between Softening Point and Annealing Range (Approximately 10 8 Pa(dot)s to Approximately 10) |
| ASTM C 1351M-1996 |
用固態垂直汽缸粘滯壓縮在104巴(點)和108巴(點)的玻璃黏滯度測定的標準試驗方法 |
Standard Test Method for Measurement of Viscosity of Glass Between 104 Pa-s and 108 Pa-s by Viscous Compression of a Solid Right Cylinder [Metric] |
5分鐘獲取標準報價 咨詢電話：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com