微信掃一掃，立即回復！
| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| BS 3900-J13 | 涂料的試驗方法.涂覆粉試驗.用激光衍射法分析粒徑 | Methods of test for paints - Testing of coating powders - Particle size analysis by laser diffraction |
| BS 5381-2 | 煙草和煙草制品物理特性測定方法.第2部分:用激光束測量儀器測定卷煙和濾嘴標準直徑 | Methods for determination of physical properties of tobacco and tobacco products - Nominal diameter of cigarettes and filter rods using a laser beam measuring apparatus |
| BS 6955-1 | 振動和沖擊傳感器的校準.采用激光干涉測量法對主振動的校準方法 | Calibration of vibration and shock pick-ups - Methods for primary vibration calibration by laser interferometry |
| BS 7334-6 | 建筑施工用測量儀器.第6部分:激光儀器使用精度的測定方法 | Measuring instruments for building construction - Methods for determining accuracy in use of laser instruments |
| BS DD IEC/PAS 61280-2-10 | 纖維光學通信子系統試驗程序.數字系統.激光發射機的時間分辨線性調頻脈沖和α因數測量 | Fibre optic communication subsystem test procedures - Digital systems - Time-resolved chirp and alpha-factor measurement of laser transmitters |
| BS EN 12254 | 激光工作場所用屏幕.安全要求和試驗 | Screens for laser working places - Safety requirements and testing |
| BS EN 12584 | 氧氣火焰切割、激光束切割和等離子體切割缺陷.術語 | Imperfections in oxyfuel flame cuts, laser beam cuts and plasma cuts - Terminology |
| BS EN 15042-1 | 覆層厚度測量和表面波紋表征.采用激光感應表面聲波法對各膜層的彈性常數、密度和厚度的測定指南 | Thickness measurement of coatings and characterization of surfaces with surface waves - Guide to the determination of elastic constants, density and thickness of films by laser induced surface acoustic waves |
| BS EN 207 | 眼睛保護.抗激光輻射用濾光鏡和護目器(激光護目鏡) | Personal eye-protection - Filters and eye-protectors against laser radiation (laser eye-protectors) |
| BS EN 208 | 眼睛防護.激光和激光系統調節工作用護目鏡(激光調節護目鏡) | Personal eye-protection - Eye-protectors for adjustment work on lasers and laser systems (laser adjustment eye-protectors) |
| BS EN 2266-005 | 航空航天系列.通用電纜.操作溫度為-55 °C 到 200 °C .紫外激光可印刷.產品標準 | Cables, electrical, for general purpose — Operating temperatures between??-55 ℃ and 200 ℃ — Part 005: UV laser printable — Product standard |
| BS EN 2266-007 | 航空航天系列.通用電纜.操作溫度為-55 °C 到 200 °C .紫外激光可印刷多芯裝套電纜.產品標準 | Cables, electrical, for general purpose — Operating temperatures between –55 ℃ and 200 ℃ — Part 007: UV laser printable multicore jacketed cable — Product standard |
| BS EN 2267-007 | 航空系列.一般用途的電纜,電器.-55°C和260°C之間的操作溫度.DMA族、單個可打印紫外激光和多芯附件.產品標 | Cables, electrical, for general purpose — Operating temperatures between -55 °C and 260 °C — Part 007: DMA family, single ink-jet printable and multicore assembly — Product standard |
| BS EN 2267-008 | 航空系列.一般用途的電纜,電器.-55°C和260°C之間的操作溫度.DM族、單個可打印紫外激光和多芯附件.產品標 | Cables, electrical, for general purpose — Operating temperatures between -55 °C and 260 °C — Part 008: DM family, single UV laser printable and multicore assembly — Product standard |
| BS EN 2267-009 | 航空系列.一般用途的電纜,電器.-55℃和260℃之間的操作溫度.DRA族、單個可打印UV激光和多芯附件.產品標準 | Cables, electrical, for general purpose — Operating temperatures between -55 ℃ and 260 ℃ — Part 009: DRA family, single and multicore assembly — Product standard |
| BS EN 2267-010 | 航空系列.一般用途的電纜,電器.-55℃和260℃之間的操作溫度.DM族、單個可打印UV激光.產品標準 | Cables, electrical, for general purpose — Operating temperatures between -55 ℃ and 260 ℃ — Part 010: DR family, single UV laser printable — Product standard |
| BS EN 2713-007 | 航空航天系列.單芯和多芯電纜的一般用途.操作溫度在-55 °C 和200 °C之間.屏蔽式（螺旋式）和有護套的可印 | Aerospace series - Cables, electrical, single and multicore for general purpose - Operating temperatures between -55 °C and 200 °C - Screened (spiral) and jacketed, UV laser printable - Product standard |
| BS EN 2714-007 | 航空航天系列.單芯和多芯電纜的一般用途.操作溫度在-55 °C 和260 °C之間.屏蔽式（螺旋式）和有護套的可印 | Cables, electrical, single and multicore for general purpose — Operating temperatures between -55 ℃ and 260 ℃ — Part 007: Screened (spiral) and jacketed, UV laser printable — Product standard |
| BS EN 2714-011 | 航空航天系列.單芯和多芯電纜的一般用途.操作溫度在-55 °C 和260 °C之間.DM族、屏蔽式（螺旋式）和有護套 | Cables, electrical, single and multicore for general purpose — Operating temperatures between -55 ℃ and 260 ℃ — Part 011: DM family, screened (spiral) and jacketed, UV laser printable — Product standard |
| BS EN 2714-012 | 航空航天系列.單芯和多芯電纜的一般用途.操作溫度在-55 °C 和260 °C之間.DM族、屏蔽式（麻花型）和有護套 | Cables, electrical, single and multicore for general purpose — Operating temperatures between -55 ℃ and 260 ℃ — Part 012: DM family, screened (braided) and jacketed, UV laser printable — Product standard |
| BS EN 2714-013 | 航空航天系列.單芯和多芯電纜的一般用途.操作溫度在-55 °C 和260 °C之間.DM族、屏蔽式（螺旋式）和有護套 | Cables, electrical, single and multicore for general purpose — Operating temperatures between -55 ℃ and 260 ℃ — Part 013: DR family, screened (spiral) and jacketed, UV laser printable — Product standard |
| BS EN 31253 | 激光和相關設備.激光裝置.機械接口 | Lasers and laser-related equipment - Laser device - Mechanical interfaces |
| BS EN 3475-706 | 航空航天系列.飛行器用電纜.試驗方法.激光可標記性 | Cables, electrical, aircraft use — Test methods — Part 706: Laser markability |
| BS EN 60601-2-22 | 醫療電氣設備.安全專門要求.激光診斷和治療設備規范 | Medical electrical equipment - Particular requirements for safety - Specification for diagnostic and therapeutic laser equipment |
| BS EN 60825-1 | 激光產品的輻射安全性.第1部分:設備分類、要求和用戶指南 | Safety of laser products - Equipment classification, requirements and user's guide |
| BS EN 60825-12 | 激光產品的安全.用于信息傳輸?shù)淖杂煽臻g光通信系統的安全 | Safety of laser products - Safety of free space optical communication systems used for transmission of information |
| BS EN 60825-2 | 激光產品的安全.光纖通信系統的安全 | Safety of laser products - Safety of optical fibre communication systems (OFCS) |
| BS EN 60825-4 | 激光產品安全.激光防護裝置 | Safety of laser products - Laser guards |
| BS EN 60856 | 50HZ/625行預錄式光反射視盤錄像系統"激光視盤".PAL制規范 | Specification for pre-recorded optical reflective videodisk system "Laser vision" 50 Hz/625 lines - PAL |
| BS EN 61040 | 激光輻射功率和能量探測器、儀表和設備規范 | Specification for power and energy measuring detectors, instruments and equipment for laser radiation |
| BS EN 61096 | 數字激光唱機用放音設備特性測量方法 | Methods of measuring the characteristics of reproducing equipment for digital audio compact discs |
| BS EN 61280-1-4 | 光纖通信子系統基本試驗程序.一般通信子系統的試驗程序.多模纖維激光發射機用二維近場數據的采集和整理 | Fibre optic communication subsystem basic test procedures - Test procedures for general communication subsystems - Collection and reduction of two-dimensional nearfield data for multimode fibre laser transmitters |
| BS EN 61751 | 激光電信模塊.可靠性評定 | Laser modules used for telecommunication - Reliability assessment |
| BS EN 62107 | 高級激光視盤.光盤互換系統.規范 | Super video compact disc - Disc-interchange system-specification |
| BS EN 62148-11 | 纖維光學有源元件及器件.包裝和接口標準.14針調制器集成激光二極管發射機 | Fibre optic active components and devices - Package and interface standards - 14-pin modulator-integrated laser diode transmitters |
| BS EN 62148-12 | 纖維光學有源元件和器件.包裝和接口標準.帶同軸RF連接器的激光發射機 | Fibre optic active components and devices - Package and interface standards - Laser transmitters with coaxial RF connector |
| BS EN 62149-3 | 纖維光學有源元件和器件.性能標準.2.5Gbit/s調制器-集成激光二極管發射機 | Fibre optic active components and devices - Performance standards - 2,5 Gbit/s modulator-integrated laser diode transmitters |
| BS EN 821-2 | 高技術陶瓷.整體陶瓷.熱物理特性. 激光閃爍法(或熱脈沖法)對熱擴散率的測定 | Advanced technical ceramics - Monolithic ceramics - Thermo-physical properties - Determination of thermal diffusivity by the laser flash (or heat pulse) method |
| BS EN ISO 11146-1 | 激光和激光相關設備.激光束寬度、發散角和束擴散率的試驗方法.無象散和簡單象散束 | Lasers and laser-related equipment - Test methods for laser beam widths, divergence angles and beam propagation ratios - Stigmatic and simple astigmatic beams |
| BS EN ISO 11146-2 | 激光和激光相關設備.激光束寬度、發散角和束擴散率的試驗方法.一般象散束 | Lasers and laser-related equipment - Test methods for laser beam widths, divergence angles and beam propagation ratios - General astigmatic beams |
| BS EN ISO 11149 | 光學和光學儀器.激光和激光相關裝置.非遠程通信激光用的光纖連接器 | Optics and optical instruments - Lasers and laser related equipment - Fibre optic connectors for non-telecommunication laser applications |
| BS EN ISO 11151-1 | 激光和激光相關設備.標準光學元件.紫外線、可見光和近紅外光譜范圍內的元件 | Lasers and laser-related equipment - Standard optical components - Components for the UV, visible and near-infrared spectral ranges |
| BS EN ISO 11151-2 | 激光和激光相關設備.標準光學元件.紅外光譜范圍內的元件 | Lasers and laser-related equipment - Standard optical components - Components for the infrared spectral range |
| BS EN ISO 11252 | 激光和激光相關設備.激光裝置.文獻工作的最低要求 | Lasers and laser-related equipment - Laser device - Minimum requirements for documentation |
| BS EN ISO 11254-1 | 激光和激光相關設備.光表面激光導致?lián)p傷閾的測定.1-on-1試驗 | Lasers and laser-related equipment - Determination of laser-induced damage threshold of optical surfaces - 1-on-1 test |
| BS EN ISO 11254-2 | 激光和激光相關設備.光表面激光導至損傷閾值的測定.S-on-1試驗 | Lasers and laser-related equipment - Determination of laser-induced damage threshold of optical surfaces - S-on-1 test |
| BS EN ISO 11551 | 光學和光學儀器.激光和激光設備 | Optics and optical instruments - Lasers and laser-related equipment - Test method for absorptance of optical laser components |
| BS EN ISO 11553-1 | 機械安全.激光加工機械.一般安全要求 | Safety of machinery - Laser processing machines - General safety requirements |
| BS EN ISO 11670 | 激光器和激光相關設備.激光束參數的試驗方法.束定位穩定性 | Lasers and laser-related equipment - Test methods for laser beam parameters - Beam positional stability |
| BS EN ISO 11810-1 | 激光和激光相關設備.手術布單和/或病人保護覆蓋物耐激光性的試驗方法和分類.基本點燃和穿透性 | Lasers and laser-related equipment - Test method and classification for laser resistance of surgical drapes and/or patient protective covers - Primary ignition and penetration |
| BS EN ISO 11990 | 光學和光學儀器.激光器和相關的激光設備.氣管柄抗激光性的測定 | Optics and optical instruments - Lasers and laser-related equipment - Determination of laser resistance of tracheal tube shafts |
| BS EN ISO 12005 | 激光器和激光相關設備.激光束參數的試驗方法.偏振 | Lasers and laser-related equipment - Test methods for laser beam parameters - Polarization |
| BS EN ISO 13694 | 光學和光學儀器.激光和激光設備.激光束能量密度分布的試驗方法 | Optics and optical instruments - Lasers and laser-related equipment - Test methods for laser beam power (energy) density distribution |
| BS EN ISO 13695 | 光學和光子學.激光和相關設備.激光的光譜特性的試驗方法 | Optics and photonics - Lasers and laser-related equipment - Test methods for the spectral characteristics of lasers |
| BS EN ISO 13919-1 | 焊接.電子和激光束焊接接頭.缺陷的質量級別導則.鋼 | Welding - Electron and laser beam welded joints - Guidance on quality levels for imperfections - Steel |
| BS EN ISO 13919-2 | 焊接.電子和激光束焊接接頭.缺陷的質量分級指南.鋁及其可焊合金 | Welding - Electron and laser beam welded joints - Guidance on quality levels for imperfections - Aluminium and its weldable alloys |
| BS EN ISO 15367-1 | 激光和激光相關設備.測定激光束波陣面形狀的試驗方法.術語及基礎領域 | Lasers and laser-related equipment - Test methods for determination of the shape of a laser beam wavefront - Terminology and fundamental aspects |
| BS EN ISO 15609-4 | 金屬材料焊接程序的規范和合格鑒定.焊接程序規范.激光束焊接 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Laser beam welding |
| BS EN ISO 15614-11 | 金屬材料焊接程序的規范和合格鑒定.焊接程序試驗.電子和激光束焊接 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Electron and laser beam welding |
| BS EN ISO 15616-1 | 高質量焊接和切割用CO2激光束機的驗收試驗.通用原則和驗收條件 | Acceptance tests for CO2- laser beam machines for high quality welding and cutting - General principles, acceptance conditions |
| BS EN ISO 15616-2 | 高質量焊接和切割用CO2激光束機的驗收試驗.靜態和動態精確度的測定 | Acceptance tests for CO2- laser beam machines for high quality welding and cutting - Measurement of static and dynamic accuracy |
| BS EN ISO 15616-3 | 高質量焊接和切割用CO2激光束機的驗收試驗.氣體流量和壓力測量儀的校正 | Acceptance tests for CO2- laser beam machines for high quality welding and cutting - Calibration of instruments for measurement of gas flow and pressure |
| BS EN ISO 17526 | 光學和光學儀器.激光器和激光相關設備.激光器的使用壽命 | Optics and optical instruments - Lasers and laser-related equipment - Lifetime of lasers |
| BS EN ISO 22827-1 | Nd:YAG激光束焊接機器的驗收試驗.帶光纖送的機器.激光裝配 | Acceptance tests for Nd:YAG laser beam welding machines - Machines with optical fibre delivery - Laser assembly |
| BS EN ISO 22827-2 | Nd:YAG激光束焊接機器的驗收試驗.帶光纖傳送的機器.移動機理 | Acceptance tests for Nd:YAG laser beam welding machines - Machines with optical fibre delivery - Moving mechanism |
| BS IEC 60825-8 | 激光產品的安全.醫療激光設備安全使用指南 | Safety of laser products - Guidelines for the safe use of medical laser equipment |
| BS ISO 10110-13 | 光學和光學儀器.光學元件和系統圖紙的制備.第13部分:激光輻射損壞閾值 | Optics and optical instruments - Preparation of drawings for optical elements and systems - Laser irradiation damage threshold |
| BS ISO 10110-17 | 光學和光學儀器.光學元件和系統制圖準備.激光輻射損害閾 | Optics and optical instruments - Preparation of drawings for optical elements and systems - Laser irradiation damage threshold |
| BS ISO 13320-1 | 粒度分析.激光衍射方法.一般規則 | Particle size analysis - Laser diffraction methods - General principles |
| BS ISO 14408 | 激光外科用氣管管子的設計.標記和附加信息要求 | Tracheal tubes designed for laser surgery - Requirements for marking and accompanying information |
| BS ISO 16063-11 | 振動和沖擊傳感器的校準方法.采用激光干涉量度法的主要振動校準 | Methods for the calibration of vibration and shock transducers - Primary vibration calibration by laser interferometry |
| BS ISO 16063-13 | 振動和沖擊傳感器的校準方法.采用激光干涉測量法的主要沖擊校準 | Methods for the calibration of vibration and shock transducers - Primary shock calibration using laser interferometry |
| BS ISO 22826 | 金屬材料焊縫的破壞性試驗.激光和電子束焊測定窄接頭硬度的試驗(維氏和努氏硬度試驗) | Destructive tests on welds in metallic materials - Hardness testing of narrow joints welded by laser and electron beam (Vickers and Knoop hardness tests) |
| BS ISO TR 11552 | 激光和與激光相關的設備.激光材料-加工機械.金屬切削的性能規范和基準點 | Lasers and laser-related equipment - Laser materials-processing machines - Performance specifications and benchmarks for cutting of metals |
| BS ISO TR 11991 | 上導氣管激光外科手術時導氣管的管理指南 | Guidance on airway management during laser surgery of upper airway |
| BS QC 720102 | 光纖系統和子系統用帶引線的激光二極管模數的空白詳細規范 | Blank detail specification for laser diode modules with pigtail for fibre optic systems and subsystems |
| 編號 | 中文名稱 | 英文名稱 |