微信掃一掃，立即回復！
| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| ANSI/ASTM D1525 | 塑料維卡(Vicat)軟化溫度試驗方法(08.01) | Test Method for Vicat Softening Temperature of Plastics (08.01) |
| ANSI/ASTM D2319 | 硬瀝青軟化點的試驗方法(空氣中立方塊試驗法) | Test Method for Softening Point of Pitch (Cube-In-Air Method) |
| ANSI/ASTM D3104 | 瀝青軟化點的試驗方法(Mettler軟化點法) | Test Method for Softening Point of Pitches (Mettler Softening Point Method) |
| ANSI/ASTM D3461 | 地瀝青和硬瀝青軟化點測試方法(Mettler杯球法) | Test Method for Softening Point of Asphalt and Pitch (Mettler Cup-And-Ball Method) |
| ANSI/ASTM D61 | 硬瀝青軟化點試驗方法(水中方塊法) | Test Method for Softening Point of Pitches (Cube-In-Water Method) |
| ANSI/NSF 44 | 民用陽離子交換水軟化劑(i11) | Residential cation exchange water softeners (i11) |
| ANSI/NSF 44?i10) | 住宅用陽離子交換水軟化劑 | Residential Cation Exchange Water Softeners (i10) |
| ANSI/NSF 44?(i10) | 住宅用陽離子交換水軟化器 | Residential Cation Exchange Water Softeners (i10) |
| ASTM C 1350M | 在軟化點和退火范圍(大約108Pa.s到大約1013Pa.s)之間玻璃黏滯度測定的標準試驗方法 | Standard Test Method for Measurement of Viscosity of Glass Between Softening Point and Annealing Range (Approximately 108 Pa˙s to Approximately 10 13 Pa˙s) by Beam Bending (Metric) |
| ASTM C 336 | 用纖維伸長法測定玻璃的軟化點和應變點的試驗方法 | Test Method for Annealing Point and Strain Point of Glass by Fiber Elongation |
| ASTM C 338 | 玻璃的軟化點的標準試驗方法 | Standard Test Method for Softening Point of Glass |
| ASTM C 598 | 用梁彎曲法測定玻璃的軟化點和應變點的標準試驗方法 | Standard Test Method for Annealing Point and Strain Point of Glass by Beam Bending |
| ASTM C 965 | 軟化點以上的玻璃粘度的測定的標準實施規程 | Standard Practice for Measuring Viscosity of Glass Above the Softening Point |
| ASTM D 2319 | 硬瀝青軟化點的標準試驗方法(空氣中立方塊試驗法) | Standard Test Method for Softening Point of Pitch (Cube-in-Air Method) |
| ASTM D 3104 | 硬瀝青軟化點的標準試驗方法 | Standard Test Method for Softening Point of Pitches (Mettler Softening Point Method) |
| ASTM D 3461 | 硬瀝青軟化點的試驗方法(米勒杯球法) | Standard Test Method for Softening Point of Asphalt and Pitch (Mettler Cup-and-Ball Method) |
| ASTM D 36 | 瀝青軟化點標準試驗方法(瀝青軟化點測定器) | Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus) |
| ASTM D 3642 | 某些堿溶性樹脂軟化點的試驗方法 | Test Method for Softening Point of Certain Alkali-Soluble Resins |
| ASTM D 5070 | 采用電位滴定法的織物軟化劑中合成季胺鹽的標準試驗方法 | Standard Test Method for Synthetic Quaternary Ammonium Salts in Fabric Softeners by Potentiometric Titrations |
| ASTM D 5237 | 織物軟化劑評定的標準指南 | Standard Guide for Evaluating Fabric Softeners |
| ASTM D 5346 | 測定油乳液和軟化化合物用石油潤滑油傾點的試驗方法 | Test Method for Determination of the Pour Point of Petroleum Oil Used in Fatliquors and Softening Compounds |
| ASTM D 6090 | 軟化點樹脂標準試驗方法(杯球法) | Standard Test Method for Softening Point Resins (Mettler Cup and Ball Method) |
| ASTM D 61 | 硬瀝青的軟化點的試驗方法(水中方塊試驗法) | Standard Test Method for Softening Point of Pitches (Cube-in-Water Method) |
| ASTM D 6493 | 用自動環球儀測定烴類樹脂軟化點的標準試驗方法 | Standard Test Method for Softening Point of Hydrocarbon Resins by Automated Ring and Ball Apparatus |
| ASTM E 2347 | 使用熱機分析法測試壓痕軟化溫度的標準試驗方法 | Standard Test Method for Indentation Softening Temperature by Thermomechanical Analysis |
| ASTM E 28 | 用環球儀測定從松脂制品中取得的樹脂的軟化點的標準試驗方法 | Standard Test Methods for Softening Point of Resins Derived from Naval Stores by Ring-and-Ball Apparatus |
| BS 2HR 401 | 冷加工和軟化的無縫鎳鉻鈦鋁耐熱合金管(鎳基、Cr 19.5、Ti 2.2、Al 1.4)規范 | Specification for nickel-chromium-titanium-aluminium heat-resisting alloy cold worked and softened seamless tubes (nickel base, Cr 19.5, Ti 2.2, Al 1.4) |
| BS 6043-1.3 | 制鋁工業用炭素材料取樣與試驗方法.第1部分:電極硬柏油脂.第3節:軟化點測定(環、球法) | Methods of sampling and test for carbonaceous materials used in aluminium manufacture - Electrode pitch - Determination of softening point (ring and ball method) |
| BS 6782-6 | 涂料用粘合劑.第6部分:軟化點的測定方法 | Binders for paints - Method for determination of softening point (ring and ball method) |
| BS 7034-6 | 玻璃粘度和測定粘度固定點.第6部分:軟化點的測定方法 | Viscosity and viscometric fixed points of glass - Method for the determination of softening point |
| BS EN 1238 | 粘合劑.熱塑性粘合劑軟化點的測定(環形和球形) | Adhesives - Determination of the softening point of thermoplastic adhesives (ring and ball) |
| BS EN 1427 | 石油及其制品的試驗方法.瀝青和瀝青粘合劑.軟化點的測定.環和球軟點測定法 | Methods of test for petroleum and its products - Bitumen and bituminous binders - Determination of softening point - Ring and ball method |
| BS EN 2155-14 | 飛機窗玻璃用透明材料的試驗方法.1/10維卡特軟化溫度的測定 | Test methods for transparent materials for aircraft glazing - Determination of the 1/10 Vicat softening temperature |
| BS EN 727 | 塑料管道和管道系統.熱塑性塑料管和配件.維卡(vicat)軟化溫度的測定 | Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST) |
| BS EN ISO 306 | 塑料.熱塑性材料.維卡(VICAT)軟化溫度的測定 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) |
| BS HR 209 | 鎳-鉻-鈷-鉬-鈦-鋁耐熱合金薄板材、帶材和板材:軟化的(鎳基、Cr18、Co14、 Mo7、Ti2.2、Al2.1)規范 | Specification for nickel-chromium-cobalt-molybdenum-titanium-aluminium heat-resisting alloy sheet, strip and plate: softened (nickel base, Cr 18, Co 14, Mo 7, Ti 2.2, Al 2.1) |
| BS HR 402 | 冷加工和軟化的無縫鎳鉻鈷鈦鋁耐熱合金管(鎳基、Cr19.5、Co18.0、Ti2.5、Al1.5)規范 | Specification for nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy cold worked and softened seamless tubes (nickel base, Cr 19.5, Co 18.0, Ti 2.5, Al 1.5) |
| BS HR 403 | 冷加工和軟化的無縫鎳鉻鈦耐熱合金管(鎳基、Cr19.5、Ti0.4)規范 | Specification for nickel-chromium-titanium heat-resisting alloy cold-worked and softened seamless tubes (nickel base, Cr 19.5, Ti 0.4) |
| BS HR 506 | 鎳-鉻-鈷-鈦-鋁耐熱合金線材:軟化的(鎳基、Cr19.5、Co1.8、Ti2.5、Al1.5)規范 | Nickel-chromium-cobalt-titanium-aluminium heat-resisting alloy wire: softened (Nickel base, Cr 19.5, Co 18, Ti 2.5, Al 1.5) |
| BS ISO 4625-1 | 色漆和清漆用粘合劑.軟化點的測定.環和球法 | Binders for paint and varnishes - Determination of softening point - Ring-and-ball method |
| BS ISO 4625-2 | 色漆和清漆用粘合劑.軟化點的測定.杯和球法 | Binders for paint and varnishes - Determination of softening point - Cup-and-ball method |
| DIN 1996-15 | 筑路和相關用途瀝青材料的檢驗.第15部分:根據威廉米法測定軟化點 | Testing of Bituminous Materials for Road Building and Related Purposes; Determination of Softening Point in accordance with Wilhelmi |
| DIN 29640 | 航空航天.丙烯酸酯塑料的軟化處理.制造規程 | Aerospace; tempering of acrylic plastics; directives for manufacture |
| DIN 51920 | 炭素材料試驗.Mettler軟化點的測定.粘接材料和浸漬材料 | Testing of carbon materials; determination of the Mettler softening point; binding and impregnating materials |
| DIN 52025 | 含碳材料的檢驗.Kraeme-Sarnow軟化點的測定 | Testing of carbonaceous materials - Determination of the Kraemer-Sarnow softening point |
| DIN 53180 | 漆和類似涂料的粘結劑.樹脂軟化溫度測定 | Binders for paints and varnishes - Determination of the softening temperature of resins |
| DIN EN 1238 | 膠粘劑.熱塑性粘接劑(環型和球型)軟化點的測定 | Adhesives - Determination of the softening point of thermoplastic adhesives (ring and ball); German version EN 1238:1999 |
| DIN EN 1427 | 瀝青和瀝青粘合劑.軟化點測定.圓環法和壓球法 | Bitumen and bituminous binders - Determination of the softening point - Ring and ball method; German version EN 1427:1999 |
| DIN EN 14743 | 建筑物內水處理設備.軟化劑.性能、安全和試驗的要求 | Water conditioning equipment inside buildings - Softeners - Requirements for performance, safety and testing; German version EN 14743:2005 |
| DIN EN 2155-14 | 航空航天系列.飛行器上窗玻璃用透明材料的試驗方法.第14部分:1/10維卡特軟化溫度的測定 | Aerospace series; test methods for transparent materials for aircraft glazing; part 14: determination of the 1/10 vicat softening temperature; German version EN 2155-14:1993 |
| DIN EN 727 | 塑料管道和管道輸送系統.熱塑塑料管和管件.維卡軟化溫度(VST)的測定; 德文版本 EN 727:1994 | Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST); German version EN 727:1994 |
| DIN EN ISO 306 | 塑料.熱塑性材料.維卡特(VICAT)軟化溫度的測定(VST) | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2004); German version EN ISO 306:2004 |
| DIN EN ISO 4625-1 | 色漆和清漆用粘合劑.軟化點的測定.第1部分:環-球法 | Binders for paints and varnishes - Determination of softening point - Part 1: Ring-and-ball method (ISO 4625-1:2004); German version EN ISO 4625-1:2006 |
| DIN EN ISO 4625-2 | 色漆和清漆用粘合劑.軟化點的測定.第2部分:環窩接合法 | Binders for paints and varnishes - Determination of softening point - Part 2: Cup-and-ball method (ISO 4625-2:2004); German version EN ISO 4625-2:2006 |
| DIN ISO 7884-6 | 玻璃.粘度和粘度固定點.第6部分:軟化點的測定 | Glass - Viscosity and viscometric fixed points - Part 6: Determination of softening point (ISO 7884-6:1987) |
| EN 1238 | 膠粘劑 熱塑性膠粘劑軟化點的測定（環和球） | Adhesives - Determination of the softening point of thermoplastic adhesives (ring and ball) |
| EN 1427 | 瀝青和瀝青粘合劑 軟化點的測定 圓環法和圓球法 | Bitumen and bituminous binders - Determination of the softening point - Ring and ball method |
| EN 727 | 塑料管道和導管系統 熱塑性管和配件 維卡（Vicat）軟化溫度（VST）的測定 | Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST) |
| EN ISO 306 | 塑料 熱塑性材料 維卡軟化溫度的測定 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:1994) |
| GB/T 11409.3 | 橡膠防老劑、硫化促進劑軟化點的測定 | Test method of softening point for rubber antiagers and vulcanizing accelerators |
| GB/T 12007.6 | 環氧樹脂軟化點測定方法環球法 | Epoxide resins--Determination of softening point--Ring and ball method |
| GB/T 15332 | 熱熔膠粘劑軟化點的測定環球法 | Determination of the softening point ofhot-melt adhesives--Ball and ring method |
| GB/T 1633 | 熱塑性塑料維卡軟化溫度(VST)的測定 | Plastics--Thermoplastic materials--Determination of Vicat softening temperature(VST) |
| GB/T 2294 | 焦化固體類產品軟化點測定方法 | Solid products of coal carbonization--Determination of softening point |
| GB/T 4507 | 瀝青軟化點測定法(環球法) | Standard test method for softening point of bitumen (Ring-and-ball apparatus) |
| GB/T 5989 | 耐火制品荷重軟化溫度試驗方法示差-升溫法 | Refractory products--Determination of refractoriness-under-load--Differential-with rising temperature |
| GB/T 8802 | 熱塑性塑料管材、管件維卡軟化溫度的測定 | Thermoplastics pipes and fitting--Determination of vicat softening temperature |
| GB/T 9284 | 色漆和清漆用漆基軟化點的測定環球法 | Binders for paints and varnishes--Determination of softening point--Ring-and-ball method |
| ISO 17235 | 皮革.物理和機械試驗.軟化度測定 | Leather - Physical and mechanical tests - Determination of softness |
| ISO 1893 | 耐火制品.荷重軟化溫度(荷重耐溶性)的測定.升溫示差法 | Refractory products - Determination of refractoriness-under-load - Differential method with rising temperature |
| ISO 2507-1 | 熱塑性塑料管材和管件 維卡軟化溫度 第1部分:一般試驗方法 | Thermoplastics pipes and fittings - Vicat softening temperature - Part 1: General test method |
| ISO 2507-2 | 熱塑性塑料管材和管件 維卡軟化溫度 第2部分:硬聚氯乙烯(PVC-V)或氯化聚氯乙烯(PVC-C)管材及管件和高抗沖聚 | Thermoplastics pipes and fittings - Vicat softening temperature - Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly(vinyl chloride) (PVC-HI) pipes |
| ISO 2507-3 | 熱塑性塑料管材和管件 維卡軟化溫度 第3部分:丙烯腈-丁二烯-苯乙烯共聚物和丙烯腈-丁二烯-丙烯酸酯共聚物管 | Thermoplastics pipes and fittings - Vicat softening temperature - Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings |
| ISO 306 | 塑料.熱塑性材料.維卡特(VICAT)軟化溫度的測定 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) |
| ISO 4625-1 | 色漆和清漆用粘合劑.軟化點的測定.第1部分:環球法 | Binders for paints and varnishes - Determination of softening point - Part 1: Ring-and-ball method |
| ISO 4625-2 | 色漆和清漆用粘合劑.軟化點的測定.第2部分:環窩接合法 | Binders for paints and varnishes - Determination of softening point - Part 2: Cup-and-ball method |
| ISO 5940 | 鋁生產用碳素材料 電極用瀝青 用環和球法測定軟化點 | Carbonaceous materials for the production of aluminium; Pitch for electrodes; Determination of softening point by the ring-and-ball method |
| ISO 7884-6 | 玻璃 粘度和粘度固定點 第6部分:軟化點的測定 | Glass; Viscosity and viscometric fixed points; Part 6 : Determination of softening point |
| JB/T 4279.8 | 漆包繞組線試驗儀器設備檢定方法 第8部分：軟化擊穿試驗儀 | Verification procedure for test equipment of enamelled winding wire Part8:Cut-through tester |
| JB/T 5636 | 光學玻璃軟化加熱爐 能耗分等 | () |
| JB/T 5705 | 鋁材軟化退火電阻加熱爐 能耗分等 | () |
| JB/T 5706 | 銅材軟化退火電阻加熱爐 能耗分等 | () |
| JIS K5601-2-2 | 涂料成份的試驗方法.第2部分:溶劑溶解物質的成份分析.第21節:軟化點(環和球法) | Testing methods for paint components -- Part 2: Component analysis in solvent soluble matter -- Section 2: Softening point (Ring and ball method) |
| JIS K6863 | 熱溶粘接劑軟化點的試驗方法 | Testing methods for the softening point of hot melt adhesives |
| JIS K7196 | 用熱機械分析法測定熱塑性塑料薄膜及薄板軟化溫度的測試方法 | Testing method for softening temperature of thermoplastics film and sheeting by thermomechanical analysis |
| JIS K7206 | 塑料.熱塑性材料.維卡軟化溫度的測定 | Plastics -- Thermoplastic materials -- Determination of Vicat softening temperature (VST) |
| JIS K7234 | 環氧樹脂軟化點的測試方法 | Testing methods for softening point of epoxide resins |
| JIS R3103-1 | 玻璃的粘度和測粘固定點.第1部分:軟化點的測定 | Viscosity and viscometric fixed points of glass -- Part 1: Determination of softening point |
| JIS T3231 | 硬化心切開術/靜脈儲存系統(帶或不帶過濾器)以及軟化靜脈儲存袋 | Hard-shell cardiotomy/venous reservoir systems (with/without filter) and soft venous reservoir bags |
| MT/T 44-1987(2005) | 煤和巖石單向抗壓強度及軟化系數測定方法 | () |
| NF B30-102 | 玻璃.軟化溫度的測定.(LITTLETON點) | (GLASS. DETERMINATION OF SOFTENING POINT. (LITTLETON POINT).) |
| NF G52-033 | 皮革.物理和機械試驗.軟化度測定 | (Leather - Physical and mechanical tests - Determination of softness.) |
| NF L17-600-14 | 航空航天系列.飛機窗用透明材料的試驗方法.第14部分:1/10維卡軟化溫度的測定(EN 2155-14) | (Aerospace series. Test methods for transparent materials for aircraft glazing. Part 14 : determination of the 1/10 vicat softening temperature.) |
| NF P98-623 | 路面橫標記.路面上使用的標記.聚乙烯樹脂軟化的分析 | (HORIZONTAL ROAD MARKING. MARKINGS APPLIED ON THE ROADS. ANALYSIS OF SLIGHTLY OR NON POLAR PLASTICIZERS OF POLYDIENIC RESINS.) |
| NF T20-167 | 生產鋁用碳質材料.電極用瀝青.用環球法測定軟化點 | (CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM. PITCH FOR ELECTRODES. DETERMINATION OF SOFTENING POINT BY THE RING-BALL METHOD.) |
| NF T51-021 | 塑料.熱塑塑料.維卡(VICAT)軟化溫度的測定 | (Plastics. Thermoplastic materials. Determination of Vicat softening temperature (VST).) |
| NF T51-437 | 塑料.固態酚樹脂.軟化點的測定.珠環法 | (PLASTICS. SOLID PHENOLIC RESINS. DETERMINATION OF SOFTENING POINT. “BALL AND RING“ METHOD.) |
| NF T54-024 | 塑料管道系統.熱塑塑料管和配件.維卡軟化點的測定 | (PLASTICS PIPING AND DUCTING SYSTEMS. THERMOPLASTICS PIPES AND FITTINGS. DETERMINATION OF VICAT SOFTENING TEMPERATURE (VST). (EUROPEAN STANDARD EN 727).) |
| NF T60-147 | 石油產品.石蠟產品軟化點的測定.環法和球法 | (Petroleum products - Determination of softening point of paraffin products - Ring and ball method.) |
| NF T66-008 | 瀝青和瀝青粘合劑.軟化點的測定.圓環法和壓球法 | (Bitumen and bituminous binders - Determination of softening point - Ring and Ball method.) |
| QC/T 29089-1992(2005) | 汽車軟化儀表板表皮 | () |
| SY/T 5644-1993(2006年確認) | 石油瀝青軟化點試驗器技術條件 | () |
| YB/T 2203-1998(2005) | 耐火澆注料荷重軟化溫度試驗方法（非示差-升溫法） | () |
| YB/T 370-1995(2005) | 耐火制品荷重軟化溫度試驗方法（非示差-升溫法） | () |
| YB/T 4024-1991(2005) | 耐火泥漿荷重軟化溫度試驗方法 （升溫法） | () |
| prEN 2120 | 航空航天系列 軟化和冷拉鋼FE-PA12 棒材和線材0.25毫米D2.5毫米 | Aerospace series; steel FE-PA 12, softened and cold drawn; bars and wires 0,25 mm D 2,5 mm |
| prEN 2469 | 航空航天系列 氣體熔化鋼FE-PA3901 (X1CrNi18-10) 軟化的 鋼絲 0,4 D 12,5 m | Aerospace series - Steel FE-PA3901 (X1CrNi18-10) air melted - Softened - Wires - 0,4 D 12,5 mm - 450 MPa R<(Index)m> 650 MPa |
| prEN 3163 | 航空航天系列 FE-PM3801 (X5CrNiCu17-4)空氣熔煉軟化鋼 鍛坯a 或 D≥300 mm | Aerospace series - Steel FE-PM3801 (X5CrNiCu17-4) air melted, softened - Forging stock a or D ≥ 300 mm |
| prEN 3359 | 航空航天系列 真空感應熔煉和消耗電極再熔煉固溶處理和沉淀處理軟化的FE-PM1503 (X3CrNiMoAl13-8-2)鋼 鍛 | Aerospace series - Steel FE-PM1503 (X3CrNiMoAl 13-8-2) vacuum induction melted and consumable electrode remelted - Softened - Forging stock - a or D 300 mm |
| prEN 3364 | 航空航天系列 消耗電極再熔煉軟化的FE-PM1802 (X5CrNiCu15-5)鋼 鍛坯a 或 D≤300 mm | Aerospace series - Steel FE-PM1802 (X5CrNiCu15-5) consumable electrode remelted, softened - Forging stock a or D 300 mm |
| prEN 3365 | 航空航天系列 空氣熔煉軟化的FE-PM3901 (X15CrNi17-3)鋼 鍛坯a 或 D≤ 300 mm | Aerospace series - Steel FE-PM3901 (X15CrNi17-3) air melted - Softened - Forging stock - a or D 300 mm |
| prEN 3476 | 航空航天系列 FE-PL1501 (30CrMo12)空氣熔煉鋼軟化鍛壞 a 或 D≤300 mm | Aerospace series - Steel FE-PL1501 (30CrMo12) air melted - Softened - Forging stock - a or D 300 mm |
| prEN 3511 | 航空航天系列 FE-PL1801 (100Cr6)真空感應熔煉和的消耗熔化電極再熔鋼 軟化的、機加工軸承制造用棒材a或 | Aerospace series - Steel FE-PL1801 (100Cr6); vacuum induction melted and consumable electrode remelted - Softened - Bar for the manufacture of machined bearings - a or D 130 mm |
| prEN 3516 | 航空航天系列 FE-PL8201 (41NiCrMo2)空氣熔煉 軟化的鋼 鍛坯 a 或 D≤300 mm | Aerospace series - Steel FE-PL8201 (41NiCrMo2) air melted - Softened - Forging stock - a or D 300 mm |
| prEN 3816 | 航空航天系列 FE-PA3601 (X6CrNiTi18-10) 空氣熔煉鋼 、軟化和冷軋 薄板和帶 a≤3 mm、 Rm≥800 MPa | Aerospace series - Steel FE-PA3601 (X6CrNiTi18-10) air melted, softened and cold rolled - Sheet and strip a 3 mm Rm≥ 800 MPa |
| prEN 3990 | 航空航天系列 FE-PA2801 (X60NiMnCr13-5-3)軟化的鋼 機加工用棒 De≤150 mm、 650 MPa≤Rm 900 MPa | Aerospace series - Steel FE-PA2801 (X60NiMnCr13-5-3) softened - Bar for machining D<(Index)e> 150 mm, 650 MPa R<(Index) |
| prEN 3992 | 航空航天系列 FE-PA2801 (X60NiMnCr13-5-3)軟化的鋼 鍛件 De≤150 mm、 620 MPa≤Rm≤900 MPa | Aerospace series - Steel FE-PA2801 (X60NiMnCr13-5-3) softened - Forgings D<(Index)e> 150 mm, 620 MPa R<(Index)m> 900 MPa |
| prEN 4089 | 航空航天系列 真空感應熔煉和真空電弧再熔、軟化FE-PL5101 (13MoCrNiV4-4-3-1)鋼 鍛坯a 或 D≤150 mm | Aerospace series - Steel FE-PL5101 (13MoCrNiV4-4-3-1) vacuum induction melted and vacuum arc remelted, softened - Forging stock a or D 150 mm |
| prEN 4346 | 航空航天系列 FE-PM1505 (X1CrNiMoAlTi12-9-2) 真空感應熔煉和消耗電極再熔煉軟化的鋼 鍛坯a 或D≤300 | Aerospace series - Steel FE-PM1505 (X1CrNiMoAlTi12-9-2) - Vacuum induction melted and consumable electrode remelted - Softened - Forging stock a or D 300 mm |
| prEN 4347 | 航空航天系列 FE-PM1506 (X3CrNiMoAl13-8-2)真空感應熔煉和再消耗電極再熔煉軟化的鋼 鍛坯a 或D≤300 mm | Aerospace series - Steel FE-PM1506 (X3CrNiMoAl13-8-2) - Vacuum induction melted and consumable electrode remelted - Softened - Forging stock a or D 300 mm |
| prEN ISO 306 | 塑料 熱塑性材料 維卡軟化溫度的測定 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO/DIS 306:2002) |
| 編號 | 中文名稱 | 英文名稱 |