微信掃一掃，立即回復！
| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| ANSI/ADA 38 | 金屬陶瓷體系 | Metal-Ceramic Systems |
| ASTM C 1300 | 用干涉法測定玻璃原料和衛生陶瓷材料線性熱膨脹的標準試驗方法 | Standard Test Method for Linear Thermal Expansion of Glaze Frits and Ceramic Whiteware Materials by the Interferometric Method |
| ASTM C 1525 | 用水淬火法測定高級陶瓷制品耐熱沖擊性的標準試驗方法 | Standard Test Method for Determination of Thermal Shock Resistance for Advanced Ceramics by Water Quenching |
| ASTM C 1605 | 使用波長色散X射線熒光光譜法進行白色陶瓷材料化學分析的標準試驗方法 | Standard Test Methods for Chemical Analysis of Ceramic Whiteware Materials Using Wavelength Dispersive X-Ray Fluorescence Spectrometry |
| ASTM C 329 | 焙燒衛生陶瓷材料比重的標準試驗方法 | Standard Test Method for Specific Gravity of Fired Ceramic Whiteware Materials |
| ASTM C 346 | 陶瓷材料制45度鏡面光澤度的試驗方法 | Test Method for 45-Deg Specular Gloss of Ceramic Materials |
| ASTM C 370 | 焙燒衛生陶瓷制品受潮膨脹的標準試驗方法 | Standard Test Method for Moisture Expansion of Fired Whiteware Products |
| ASTM C 372 | 用膨脹儀測定搪瓷及釉面焙燒制品與焙燒衛生陶瓷制品的線性熱膨脹的標準試驗方法 | Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method |
| ASTM C 373 | 焙燒衛生陶瓷制品的吸水率、松密度、表觀多孔性與表觀比重的標準試驗方法 | Standard Test Method for Water Absorption, Bulk Density, Apparent Porosity, and Apparent Specific Gravity of Fired Whiteware Products |
| ASTM C 408 | 衛生陶瓷制品傳熱性的試驗方法 | Test Method for Thermal Conductivity of Whiteware Ceramics |
| ASTM C 539 | 用干擾法測定搪瓷、釉瓷和白色陶瓷材料線性熱膨脹的試驗方法 | Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Ceramic Whiteware Materials by Interferometric Method |
| ASTM C 623 | 用共振現象對玻璃和玻璃陶瓷材料的楊氏模量、剪切模量及泊松比的標準試驗方法 | Standard Test Method for Young's Modulus, Shear Modulus, and Poisson's Ratio for Glass and Glass-Ceramics by Resonance |
| ASTM C 674 | 衛生陶瓷材料的撓曲特性的試驗方法 | Test Methods for Flexural Properties of Ceramic Whiteware Materials |
| ASTM C 773 | 焙燒的白色陶瓷材料抗壓(壓碎)強度的試驗方法 | Standard Test Method for Compressive (Crushing) Strength of Fired Whiteware Materials |
| ASTM D 116 | 電氣設備用上釉陶瓷材料的試驗 | Testing Vitrified Ceramic Materials for Electrical Applications |
| ASTM F 19 | 鍍金屬陶瓷密封件抗拉及真空試驗方法 | Test Method for Tension and Vacuum Testing Metalized Ceramic Seals |
| BS 1902-6 | 耐火材料的試驗方法.第6部分:陶瓷纖維制品 | Methods of testing refractory materials - Ceramic fibre products |
| BS 4495 | 陶瓷和金屬陶瓷度層的熔噴法推薦標準 | Recommendations for the flame spraying of ceramic and cermet coatings |
| BS 6466 | 陶瓷纖維爐襯的設計和安裝實用規程 | Code of practice for design and installation of ceramic fibre furnace linings |
| BS 6748 | 陶瓷制品、玻璃器皿、玻璃陶瓷制品和搪瓷制品金屬析出極限規范 | Specification for limits of metal release from ceramic ware, glassware, glass ceramic ware and vitreous enamel ware |
| BS 7134-0 | 工程陶瓷試驗.第0部分:取樣導言和指南 | Testing of engineering ceramics - Introduction and guide to sampling |
| BS 7134-3.5 | 工程陶瓷的試驗.熱機性能.熱塑性變形的測定方法(下垂法) | Testing of engineering ceramics - Thermo-mechanical properties - Methods for determination of pyroplastic deformation (sagging) |
| BS 7134-4.1 | 工程陶瓷試驗.熱物理性能.熱膨脹測定方法 | Testing of engineering ceramics - Thermo-physical properties - Method for determination of thermal expansion |
| BS 7225-3.1 | 耐火材料分類.第3部分:陶瓷纖維制品.第1節:覆蓋層、底板、氈墊和紙 | Classification of refractories - Ceramic fibre products - Blankets , mats, felts and paper |
| BS 7253-2 | 外科植入物用非金屬材料.高純度氧化鋁陶瓷材料規范 | Non-metallic materials for surgical implants - Specification for ceramic materials based on high purity alumina |
| BS 7253-6 | 外科植入非金屬材料.基于氧化釔穩定處理的四方形氧化鋯陶瓷材料規范 | Non-metallic materials for surgical implants - Specification for ceramic materials based on yttria-stabilized tetragonal zirconia (Y-TZP) |
| BS DD CEN/TS 1071-10 | 高級工業陶瓷.陶瓷涂層的試驗方法.橫切法測定涂層厚度 | Advanced technical ceramics - Methods of test for ceramic coatings - Determination of coating thickness by cross section |
| BS DD CEN/TS 1071-7 | 高級工業陶瓷.陶瓷涂層的試驗方法.用儀器化刻痕試驗測定硬度及楊式模量 | Advanced technical ceramics - Methods of test for ceramic coatings - Determination of hardness and Young's modulus by instrumented indentation testing |
| BS DD CEN/TS 1071-8 | 高級工業陶瓷.陶瓷涂層的試驗方法.粘著性評定用洛氏針入試驗 | Advanced technical ceramics - Methods of text for ceramic coatings - Rockwell indentation test for evaluation of adhesion |
| BS DD CEN/TS 1159-4 | 高級工業陶瓷.陶瓷復合材料.熱物理性能.熱傳導性的測定 | Advanced technical ceramics - Ceramic composites - Thermophysical properties - Determination of thermal conductivity |
| BS DD CEN/TS 14425-1 | 高級工業陶瓷.整體陶瓷斷裂韌性測定的試驗方法.試驗方法選擇指南 | Advanced technical ceramics - Test methods for determination of fracture toughness of monolithic ceramics - Guide to test method selection |
| BS DD CEN/TS 14425-3 | 高級工業陶瓷.塊體陶瓷斷裂韌性測定的試驗方法.人字切口橫梁法 | Advanced technical ceramics - Test methods for determination of fracture toughness of monolithic ceramics - Chevron notched beam (CNB) method |
| BS DD CEN/TS 14425-5 | 高級工業陶瓷.單片陶瓷斷裂韌性測定的試驗方法.單邊V形切口橫梁法 | Advanced technical ceramics - Test methods for determination of fracture toughness of monolithic ceramics - Single-edge vee-notch beam (SEVNB) method |
| BS DD CEN/TS 843-6 | 高級工業陶瓷.單片陶瓷.室溫下的機械性能.斷裂面顯微鏡檢驗 | Advanced technical ceramics - Monolithic ceramics - Mechanical properties at room temperature - Guidance for fractographic investigation |
| BS DD ENV 1006 | 高級工業陶瓷.整體陶瓷.特性評定用試樣的選擇指南 | Advanced technical ceramics - Monolithic ceramics - Guidance on the selection of test pieces for the evaluation of properties |
| BS DD ENV 1071-5 | 高級工業陶瓷.陶瓷涂層的試驗方法.孔隙率測定 | Advanced technical ceramics - Methods of test for ceramic coatings - Determination of porosity |
| BS DD ENV 1071-6 | 高級工業陶瓷.陶瓷涂層的試驗方法.用微磨損損耗試驗測定耐磨性 | Advanced technical ceramics - Methods of test for ceramic coatings - Determination of the abrasion resistance of coatings by a micro-abrasion wear test |
| BS DD ENV 1094-7 | 隔熱產品.陶瓷纖維產品的試驗方法 | Insulating refractory products - Methods of test for ceramic fibre products |
| BS DD ENV 14232 | 高級工業陶瓷.術語、定義和縮寫 | Advanced technical ceramics - Terms, definitions and abbreviations |
| BS DD ENV 14273 | 高級工業陶瓷.陶瓷粉.鋯晶相的測定 | Advanced technical ceramics - Ceramic powders - Determination of crystalline phases in zirconia |
| BS EN 1007-3 | 高級工業陶瓷.陶瓷復合材料.增強纖維的試驗方法.長纖維直徑和橫截面積的測定 | Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Determination of filament diameter and cross-section area |
| BS EN 1007-4 | 高級工業陶瓷.陶瓷復合材料.纖維增強的試驗方法.環境溫度下長纖維的抗拉性能測定 | Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Determination of tensile properties of filaments at ambient temperature |
| BS EN 1007-5 | 高級工業陶瓷.陶瓷復合材料.增強纖維的試驗方法.室溫下復絲束中長絲斷開時的拉伸強度和拉伸應變分布的測定 | Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Determination of distribution of tensile strength and of tensile strain to failure of filaments within a multifilament tow at ambient temperature |
| BS EN 1071-1 | 高級工業陶瓷.陶瓷覆層的試驗方法.用觸針式輪廓測定儀測定陶瓷覆層厚度 | Advanced technical ceramics - Methods of test for ceramic coatings - Determination of coating thickness by contact probe filometer |
| BS EN 1071-2 | 高級工業陶瓷.陶瓷覆層的試驗方法.用環形研磨法測定陶瓷覆層厚度 | Advanced technical ceramics - Methods of test for ceramic coatings - Determination of coating thickness by the crater grinding method |
| BS EN 1071-4 | 高級工業陶瓷.陶瓷覆層的試驗方法.使用電探針微量分析(EPMA)測量化學成分 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 4:Determination of chemical composition by electron probe microanalysis (EPMA) |
| BS EN 1094-1 | 隔熱耐火產品.陶瓷纖維產品術語 | Insulating refractory products - Terminology for ceramic fibre products |
| BS EN 1094-3 | 絕緣耐火產品.陶瓷纖維絕緣制品的分類 | Insulating refractory products - Classification of insulating products made from ceramic fibres |
| BS EN 1159-1 | 高級工業陶瓷.陶瓷復合材料.熱機械性能.熱膨脹性的測定 | Advanced technical ceramics - Ceramic composites - Thermophysical properties - Determination of thermal expansion |
| BS EN 1159-2 | 高級工業陶瓷.陶瓷復合材料.熱機械性能.熱擴散系數的測定 | Advanced technical ceramics - Ceramic composites - Thermophysical properties - Determination of thermal diffusivity |
| BS EN 1159-3 | 高級工業陶瓷.陶瓷復合材料.熱-機械性能.比熱的測定 | Advanced technical ceramics - Ceramic composites - Thermophysical properties - Determination of specific heat capacity |
| BS EN 12291 | 高級工業陶瓷.大氣壓力下高溫空氣中陶瓷復合材料的機械性能.壓縮特性的測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature in air at atmospheric pressure - Determination of compression properties |
| BS EN 12789 | 高級工業陶瓷.在大氣壓下高溫時陶瓷復合材料的機械特性.撓曲強度的測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under air at atmospheric pressure - Determination of flexural strength |
| BS EN 1389 | 高級工業陶瓷.陶瓷復合材料.物理性能.密度和表觀孔隙率的測定 | Advanced technical ceramics - Ceramic composites - Physical properties - Determination of density and apparent porosity |
| BS EN 1892 | 高級工業陶瓷.陶瓷復合材料在惰性氣體中高溫下的機械性能.抗拉性能測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of tensile properties |
| BS EN 1893 | 高級工業陶瓷.大氣壓力下空氣中高溫情況下陶瓷成分的機械特性.拉伸特性的測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature in air at atmospheric pressure - Determination of tensile properties |
| BS EN 1894 | 高級工業陶瓷.惰性氣體環境中高溫情況下陶瓷成分的機械特性.通過有凹槽試樣的壓力荷載測定剪切強度 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of shear strength by compression loading of notched specimens |
| BS EN 50324-1 | 陶瓷材料和元件的壓電性能.術語和定義 | Piezoelectric properties of ceramic materials and components - Terms and definitions |
| BS EN 50324-2 | 陶瓷材料和元件的壓電性能.測量方法.低功率 | Piezoelectric properties of ceramic materials and components - Methods of measurement - Low power |
| BS EN 50324-3 | 陶瓷材料和元件的壓電性能.測量方法.高功率 | Piezoelectric properties of ceramic materials and components - Methods of measurement - High power |
| BS EN 623-3 | 高級工程陶瓷.單片陶瓷.一般和紋理特性.粒度和粒度分布的測定(線性截取法表征) | Advanced technical ceramics - Monolithic ceramics - General and textural properties - Determination of grain size and size distribution (characterized by the linear intercept method) |
| BS EN 623-4 | 高級工業陶瓷.塊體陶瓷.一般和紋理特性.表面粗糙度的測定 | Advanced technical ceramics - Monolithic ceramics - General and textural properties - Determination of surface roughness |
| BS EN 658-2 | 高級工業陶瓷.室溫下陶瓷復合材料的機械性能.壓縮性能的測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Determination of compression properties |
| BS EN 658-4 | 高級工業陶瓷.室溫下陶瓷復合材料的機械性能.通過有凹槽試樣的抗壓荷載測定層間的剪切強度 | Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Determination of interlaminar shear strength by compression loading of notched test specimens |
| BS EN 658-5 | 高級工業陶瓷.室溫下陶瓷復合材料的機械性能.利用短跨度彎曲試驗(三點)測定層間抗剪強度 | Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Determination of interlaminar shear strength by short span bend test (three points) |
| BS EN 725-9 | 高級工業陶瓷.陶瓷粉末的試驗方法.未夯實的體積密度的測定 | Advanced technical ceramics - Methods of test for ceramic powders - Part 9: Determination of untapped bulk density |
| BS EN 820-1 | 高級工業陶瓷.整體陶瓷的試驗方法.熱機械特性.高溫下?lián)锨鷱姸鹊臏y定 | Advanced technical ceramics - Methods of testing monolithic ceramics - Thermo-mechanical properties - Determination of flexural strength at elevated temperatures |
| BS EN 820-2 | 高級工業陶瓷.整體陶瓷的試驗方法.熱-機械特性.自重變形的測定 | Advanced technical ceramics - Methods of testing monolithic ceramics - Thermo-mechanical properties - Determination of self-loaded deformation |
| BS EN 820-3 | 高級工業陶瓷.單片陶瓷.熱機械性能.水淬火法測定耐熱沖擊 | Advanced technical ceramics - Monolithic ceramics - Thermomechanical properties - Determination of resistance to thermal shock by water quenching |
| BS EN 821-3 | 高級工業陶瓷.整體陶瓷.熱物理特性.比熱容的測定 | Advanced technical ceramics - Monolithic ceramics - Thermo-physical properties - Determination of specific heat capacity |
| BS ISO 10635 | 耐火制品.陶瓷纖維制品的試驗方法 | Refractory products - Methods of test for ceramic fibre products |
| BS ISO 15490 | 細陶瓷(高級陶瓷、高級工業陶瓷).室溫下單片陶瓷抗拉強度的試驗方法 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for tensile strength of monolithic ceramics at room temperature |
| BS ISO 20508 | 細陶瓷(高級陶瓷、高級工業陶瓷).帶有透明襯底的陶瓷薄膜的透光度的測定 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of light transmittance of ceramic films with transparent substrate |
| DD ENV 1094-3 | 絕緣耐火產品.陶瓷纖維產品分類 | Insulating refractory products. Classification of ceramic fibre products |
| DD ENV 1094-7 | 絕緣耐火制品.第7部分:陶瓷纖維制品的試驗方法 | Insulating refractory products. Methods of test for ceramic fibre products |
| DIN 40680-1 | 電工陶瓷件.容許公差 | Ceramic components for electrical purposes; admissible tolerances |
| DIN 40680-2 | 電工陶瓷件.形狀公差 | Ceramic components for electrical purposes; form tolerances |
| DIN 40686 Bb.2 | 電工致密陶瓷件的表面.表面粗糙度的測定 | Surfaces of dense ceramic components for electrical engineering; determination of surface roughness |
| DIN 40686-1 | 電工細陶瓷件的表面.定義 | Surfaces of dense ceramic components for electrical engineering; definitions |
| DIN 40686-4 | 電工細陶瓷件的表面.可軟釬焊金屬鍍層的檢驗 | Surfaces of dense ceramic components for electrical engineering; testing of soft-solderable metal coatings |
| DIN 40686-5 | 電工細陶瓷件的表面.可硬釬焊金屬鍍層的檢驗 | Surfaces of dense ceramic components for electrical engineering; testing of hard-solderable metal coatings |
| DIN 40686-6 | 電工細陶瓷件的表面.高壓、低壓絕緣子 | Surfaces of dense ceramic components for electrical engineering; high-voltage and low-voltage insulators |
| DIN 40686-7 | 電工細陶瓷件的表面.絕緣件 | Surfaces of dense ceramic components for electrical engineering; insulating parts |
| DIN 44926-1 | 電熱元件用陶瓷件.第1部分:多孔管尺寸 | Ceramic parts for electric heating elements; multiple hole tubes; dimensions |
| DIN 44926-2 | 電熱元件用陶瓷件.第2部分:開口式多孔管尺寸 | Ceramic parts for electric heating elements; open multiple hole tubes; dimensions |
| DIN 44926-3 | 電熱元件用陶瓷件.第3部分:帶連接件的螺旋盤尺寸 | Ceramic parts for electric heating elements; helical discs with connecting parts; dimensions |
| DIN 48108-1 | 電工陶瓷件.絕緣子安裝部位.開槽 | Ceramic components for electrical purposes; mounting places for insulators; grooving |
| DIN 48108-2 | 電工陶瓷件.絕緣子的安裝部位.砂磨表面 | Ceramic components for electrical purposes; mounting places for insulators; sanded surfaces |
| DIN 48108-3 | 電工陶瓷件.絕緣子安裝部位.皺紋面 | Ceramic components for electrical purposes; mounting places for insulators; undulatory profile |
| DIN 51045-2 | 采用熱效應法對固體長度變化的測定.第2部分:焙燒的細陶瓷材料的檢驗 | Determination of the change of length of solids by thermal effect; testing of fired fine ceramic materials |
| DIN 51045-3 | 采用熱效應法對固體長度變化的測定.第3部分:未焙燒的細陶瓷材料的檢驗 | Determination of the change of length of solids by thermal effect; testing of non-fired fine ceramic materials |
| DIN 51045-4 | 采用熱效應法對固體長度變化的測定.第4部分:焙燒過的普通陶瓷材料的檢驗 | Determination of the change of length of solids by thermal effect; testing of fired ordinary ceramic materials |
| DIN 51045-5 | 采用熱效應法對固體長度變化的測定.第5部分:未焙燒的普通陶瓷材料的檢驗 | Determination of the change of length of solids by thermal effect; testing of non-fired ordinary ceramic materials |
| DIN 51068-1 | 陶瓷材料的試驗.測定耐熱沖擊抗性.耐火磚水淬法 | Testing of ceramic materials; Determination of Resistance to Thermal Shock; Water quenching method for refractory bricks |
| DIN 51074-1 | 陶瓷材料的檢驗.第1部分:含氧化鉻陶瓷材料的化學分析.一般說明和試驗報告 | Testing of ceramic materials; chemical analysis of ceramic materials containing chromium oxide, general instructions and test report |
| DIN 51074-2 | 陶瓷材料的檢驗.用溶解法對含氧化鉻的陶瓷材料的化學分析 | Testing of ceramic material; chemical analysis of ceramic materials containing chromium oxide, methods of dissolution |
| DIN 51074-3 | 陶瓷材料的檢驗. 用鉻氧化物測定法對含氧化鉻的陶瓷采料的化學分析 | Testing of ceramic materials; chemical analysis of ceramic materials containing chromium oxide, determination of chromic oxide |
| DIN 51074-4 | 陶瓷材料的檢驗.第4部分:用氧化鈣測定法對含氧化鉻的陶瓷材料進行化學分析 | Testing of ceramic materials; chemical analysis of ceramic materials containing chromium oxide, determination of calcium oxide |
| DIN 51075-1 | 陶瓷材料的檢驗.碳化硅的化學分析.試樣的制備和碳化硅含量的計算 | Testing of ceramic materials; chemical analysis of silicon carbide; sample preparation and calculation of silicon carbide content |
| DIN 51075-2 | 陶瓷材料的檢驗.碳化硅的化學分析.游離碳含量的直接測定 | Testing of ceramic materials; chemical analysis of silicon carbide; direct determination of the free carbon content |
| DIN 51075-3 | 陶瓷材料的檢驗.碳化硅的化學分析.總含碳量的測定 | Testing of ceramic materials; chemical analysis of silicon carbide; determination of the total carbon content |
| DIN 51075-4 | 陶瓷材料的檢驗.碳化硅的化學分析.游離硅含量的測定 | Testing of ceramic materials; chemical analysis of silicon carbide; determination of the free silicon content |
| DIN 51075-5 | 陶瓷材料的檢驗.碳化硅的化學分析.游離碳含量的直接測定 | Testing of ceramic materials; chemical analysis of silicon carbide; indirect determination of the free carbon content |
| DIN 51076-1 | 陶瓷材料的檢驗.作為原材料的主要成份或次要成份的碳化硅的化學分析.用氧化成份和粘合料測定原料中碳化硅含 | Testing of ceramic materials; chemical analysis of silicon carbide as main or minor constituent of ceramic materials; determination of SiC in materials with oxidic components and binding materials |
| DIN 51079-1 | 陶瓷材料的檢驗.作為原材料和材料成分的碳化硅的化學分析.第1部分:用碳酸鈉和硼酸分解 | Testing of ceramic materials - Chemical analysis of silicon carbide used as raw material and as constituent in materials - Part 1: Decomposition with sodium carbonate and boric acid |
| DIN 51079-2 | 陶瓷材料的檢驗.作為原材料和材料成分的碳化硅的化學分析.第2部分:用酸進行的壓力分解 | Testing of ceramic materials - Chemical analysis of silicon carbide used as raw material and as constituent in materials - Part 2: Pressure decomposition with acid |
| DIN 51082 | 陶瓷原材料和陶瓷材料測試.不溶性粉末懸浮液pH值測定 | Testing of ceramic raw materials and ceramic materials - Determination of pH value of suspensions of non-soluble powders |
| DIN 51083-3 | 陶瓷材料的檢驗.硅酸鋁的化學分析.第3部分:分解法 | Testing of ceramic materials - Chemical analysis of alumosilicates - Part 3: Decomposition methods |
| DIN 51083-5 | 陶瓷材料的檢驗.硅酸鋁的化學分析.第5部分:二氧化鈦的測定 | Testing of ceramic materials - Chemical analysis of alumosilicates - Part 5: Determination of titanium oxide |
| DIN 51083-8 | 陶瓷材料的試驗.鋁硅酸鹽的化學分析.第8部分:用原子吸收光譜法測定氧化鎂 | Testing of ceramic materials - Chemical analysis of alumosilicates - Part 8: Determination of magnesium oxide (MgO) by atomic absorption spectrometry |
| DIN 51083-9 | 陶瓷材料的檢驗.硅酸鋁的化學分析.五氧化二磷含量的光度測定 | Testing of ceramic materials; chemical analysis of alumosilicates; photometric determination of the phosphorus-V-oxid content |
| DIN 51102-1 | 陶瓷材料的檢驗.用下水道瓦管材料結塊試驗方法測定耐酸性 | Testing of ceramic materials; determination of the acid resistance, method with lumpy test material for clay for severage |
| DIN 51110-3 | 高技術陶瓷材料檢驗.4點彎曲試驗.靜態評估.Weibull（威伯爾）參數的測定 | Testing of advanced technical ceramics; 4-point-bending test; statistical evaluation; determination of the Weibull-parameters |
| DIN CEN/TS 1071-10 | 高級工業陶瓷.陶瓷涂層的試驗方法.第10部分:由橫切法測定涂層厚度 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 10: Determination of coating thickness by cross sectioning; German version CEN/TS 1071-10:2004 |
| DIN CEN/TS 1071-11 | 高級工業陶瓷.陶瓷涂層的試驗方法.第11部分:用Stoney公式測定內壓 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 11: Determination of internal stress by the Stoney formula; German version CEN/TS 1071-11:2005 |
| DIN CEN/TS 1071-7 | 高級工業陶瓷.陶瓷涂層的試驗方法.第7部分:通過裝有測量儀器的壓痕試驗測定硬度和楊氏模量 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 7: Determination of hardness and Young's modulus by instrumented indentation testing; German version CEN/TS 1071-7:2003 |
| DIN CEN/TS 1071-8 | 高級工業陶瓷.陶瓷涂層的試驗方法.第8部分:粘性評價的洛氏亞痕試驗 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 8: Rockwell indentation test for evaluation of adhesion; German version CEN/TS 1071-8:2004 |
| DIN CEN/TS 1071-9 | 高級工業陶瓷.陶瓷涂層的試驗方法.第9部分:斷裂應變的測定 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 9: Determination of fracture strain; German version CEN/TS 1071-9:2004 |
| DIN CEN/TS 1159-4 | 高級工業陶瓷.陶瓷復合物.熱物理性能.第4部分:熱導性的測定 | Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 4: Determination of thermal conductivity; German version CEN/TS 1159-4:2004 |
| DIN CEN/TS 14425-1 | 高級工業陶瓷.單片陶瓷斷裂韌性測定的試驗方法.第1部分:試驗方法的選擇指南 | Advanced technical ceramics - Test methods for determination of fracture toughness of monolithic ceramics - Part 1: Guide to test method selection; German version CEN/TS 14425-1:2003 |
| DIN CEN/TS 14425-3 | 高級工業陶瓷.單片陶瓷斷裂韌性測定的試驗方法.第3部分:鋸齒形切口試桿法 | Advanced technical ceramics - Test methods for determination of fracture toughness of monolithic ceramics - Part 3: Chevron-notched beam (CNB) method; German version CEN/TS 14425-3:2003 |
| DIN CEN/TS 14425-5 | 高級工業陶瓷.單片陶瓷斷裂韌性測定的試驗方法.第5部分:單邊V形切口束法 | Advanced technical ceramics - Test methods for determination of fracture toughness of monolitic ceramics - Part 5: Single-edge vee-notch beam (SEVNB) method; German version CEN/TS 14425-5:2004 |
| DIN CEN/TS 15365 | 高級工業陶瓷.無化學反應環境的高溫條件下陶瓷纖維的機械性能.通過冷端法測定儒變特性 | Advanced technical ceramics - Mechanical properties of ceramic fibres at high temperature in a non-reactive environment - Determination of creep behaviour by the cold end method; German version CEN/TS 15365:2006 |
| DIN CEN/TS 15365 | 高級工業陶瓷.無化學反應環境的高溫條件下陶瓷纖維的機械性能.通過冷端法測定儒變特性 | Advanced technical ceramics - Mechanical properties of ceramic fibres at high temperature in a non-reactive environment - Determination of creep behaviour by the cold end method; German version CEN/TS 15365:2006 |
| DIN CEN/TS 820-5 | 高級工業陶瓷.塊體陶瓷試驗方法.熱機性能.第5部分:高溫下彈性模量的測定 | Advanced technical ceramics - Methods of testing monolithic ceramics - Thermomechanical properties - Part 5: Determination of elastic moduli at elevated temperatures; German version CEN/TS 820-5:2004 |
| DIN CEN/TS 843-6 | 高級工業陶瓷.塊體陶瓷.室溫下機械性能.第6部分:斷裂面顯微鏡圖像觀察指南 | Advanced technical ceramics - Monolithic ceramics - Mechanical properties at room temperature - Part 6: Guidance for fractographic investigation; German version CEN/TS 843-6:2004 |
| DIN EN 1007-4 | 高級工業陶瓷.陶瓷復合材料.纖維增強的試驗方法.第4部分:環境溫度下長纖維的抗拉性能測定 | Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 4: Determination of tensile properties of filaments at ambient temperature; German version EN 1007-4:2004 |
| DIN EN 1007-5 | 高級工業陶瓷.陶瓷復合材料.增強纖維的試驗方法.第5部分:室溫下復絲束中長絲斷開時的拉伸強度和拉伸應變分 | Advanced technical ceramics - Ceramic composites; Methods of test for reinforcements - Part 5: Determination of distribution of tensile strength and of tensile strain to failure of filaments within a multifilament tow at ambient temperature; German version EN 1007-5:2003 |
| DIN EN 1071-1 | 高級工業陶瓷.陶瓷覆層的試驗方法.第1部分:用接觸式探針輪廓測定儀測定覆層厚度 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 1: Determination of coating thickness by contact probe profilometer; German version EN 1071-1:2003 |
| DIN EN 1071-2 | 高級工程陶瓷.陶瓷覆層試驗方法.第2部分:用圓坑研磨法測定覆層厚度 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 2: Determination of coating thickness by the crater grinding method; German version EN 1071-2:2002 |
| DIN EN 1071-3 | 高級工業陶瓷.陶瓷覆層的試驗方法.第3部分:用劃痕試驗測定粘附性和其他機械失效模式 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 3: Determination of adhesion and other mechanical failure modes by a scratch test; English version EN 1071-3:2005 |
| DIN EN 1071-4 | 高級工業陶瓷.陶瓷涂層的試驗方法.第4部分:使用電探針微量分析(EPMA)測量化學成分 | Advanced technical ceramics - Methods of test for ceramic coatings - Part 4: Determination of chemical composition by electron probe microanalysis (EPMA); German version EN 1071-4:2006 |
| DIN EN 1094-1 | 絕緣耐火產品.第1部分:陶瓷纖維制品術語 | Insulating refractory products - Part 1: Terminology for ceramic fibre products; German version EN 1094-1:1997 |
| DIN EN 1094-3 | 隔熱耐火產品.第3部分:陶瓷纖維隔熱制品的分類 | Insulating refractory products - Part 3: Classification of insulating products made from ceramic fibres; German version EN 1094-3:2003 |
| DIN EN 1159-1 | 高級工業陶瓷.陶瓷復合材料.熱物理性能.第1部分:熱膨脹的測定 | Advanced technical ceramics - Ceramic composites; Thermophysical properties - Part 1: Determination of thermal expansion; German version EN 1159-1:2003 |
| DIN EN 1159-2 | 高級工業陶瓷.陶瓷復合材料.熱物理特性.第2部分:熱擴散系數的測定 | Advanced technical ceramics - Ceramic composites; Thermophysical properties - Part 2: Determination of thermal diffusivity; German version EN 1159-2:2003 |
| DIN EN 1159-3 | 高級工業陶瓷.陶瓷復合材料的熱物理性能.第3部分:比熱的測定 | Advanced technical ceramics - Ceramic composites, thermophysical properties - Part 3: Determination of specific heat capacity; German version EN 1159-3:2003 |
| DIN EN 1217 | 接觸食品的材料和物品.陶瓷制品吸水性試驗方法 | Materials and articles in contact with foodstuffs - Test methods for water absorption of ceramic articles; German version EN 1217:1998 |
| DIN EN 12289 | 高級工業陶瓷.環境溫度下陶瓷組分的機械特性.面內剪切性能的測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at ambient temperature - Determination of in-plane shear properties; German version EN 12289:2005 |
| DIN EN 12290 | 高級工業陶瓷.惰性氣體環境內高溫下陶瓷組分的機械特性.壓縮特性的測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of compression properties; German version EN 12290:2005 |
| DIN EN 12291 | 高級工業陶瓷.陶瓷復合材料在高溫、大氣壓和空氣中的機械性能.壓縮性能的測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature in air at atmospheric pressure - Determination of compression properties; German version EN 12291:2003 |
| DIN EN 12788 | 高級工業陶瓷.惰性氣體環境內高溫下陶瓷組分的機械特性.抗彎強度的測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of flexural strength; German version EN 12788:2005 |
| DIN EN 12789 | 高級工業陶瓷.大氣壓力下陶瓷復合物高溫機械特性.撓曲強度測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under air at atmospheric pressure - Determination of flexural strength; German version EN 12789:2002 |
| DIN EN 13258 | 與食品接觸的材料和用品.陶瓷制品耐碎裂性的試驗方法 | Materials and articles in contact with foodstuffs - Test methods for crazing resistance of ceramic articles; German version EN 13258:2003 |
| DIN EN 1388-1 | 與食品接觸的材料和物品.硅化表面.第1部分:測定從陶瓷制品中釋放的鉛和鎘; 德文版本 EN 1388-1:1995 | Materials and articles in contact with foodstuffs - Silicate surfaces - Part 1: Determination of the release of lead and cadmium from ceramic ware; German version EN 1388-1:1995 |
| DIN EN 1388-2 | 與食品接觸的材料和物品.硅化表面.第2部分:除陶瓷制品外測定從硅化表面釋放的鉛和鎘; 德文版本 EN 1388-2:1 | Materials and articles in contact with foodstuffs - Silicate surfaces - Part 2: Determination of the release of lead and cadmium from silicate surfaces other than ceramic ware; German version EN 1388-2:1995 |
| DIN EN 1389 | 高級工業陶瓷.陶瓷復合物.物理性能.密度和表觀孔隙率的測定 | Advanced technical ceramics - Ceramic composites - Physical properties - Determination of density and apparent porosity; German version EN 1389:2003 |
| DIN EN 1892 | 高級工業陶瓷.惰性氣體高溫環境下陶瓷組分的機械特性.抗拉特性測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of tensile properties; German version EN 1892:2005 |
| DIN EN 1893 | 高級工業陶瓷.大氣壓力高溫環境中陶瓷組分的機械特性.抗拉特性測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature in air at atmospheric pressure - Determination of tensile properties; German version EN 1893:2005 |
| DIN EN 1894 | 高級工業陶瓷.惰性氣體高溫環境中陶瓷組分的機械特性.有凹槽試樣在壓力荷載下剪切強度的測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of shear strength by compression loading of notched specimens; German version EN 1894:2005 |
| DIN EN 50324-1 | 陶瓷材料和部件的壓電性能.第1部分:術語和定義; 德文和英文版本 EN 3475-804:2002 | Piezoelectric properties of ceramic materials and components - Part 1: Terms and definitions; German version EN 50324-1:2002 |
| DIN EN 50324-2 | 陶瓷材料和部件的壓電性能.第2部分:低功率測量方法; 德文版本 EN 50324-2:2002 | Piezoelectric properties of ceramic materials and components - Part 2: Methods of measurement; Low power; German version EN 50324-2:2002 |
| DIN EN 50324-3 | 陶瓷材料和部件的壓電性能.第3部分:高功率測量方法; 德文版本 EN 50324-3:2002 | Piezoelectric properties of ceramic materials and components - Part 3: Methods of measurement; High power; German version EN 50324-3:2002 |
| DIN EN 60168 | 額定電壓超過1kV的系統用陶瓷材料或玻璃制室內和室外架空支承絕緣子試驗 | Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1 kV (IEC 60168:1994 + A1:1997 + A2:2000); German version EN 60168:1994 + A1:1997 + A2:2000 |
| DIN EN 61211 | 標稱電壓1000V以上的架空線用陶瓷材料或玻璃絕緣子.空氣中脈沖擊穿試驗 | Insulators of ceramic material or glass for overhead lines with a nominal voltage greater than 1000 V - Impulse puncture testing in air (IEC 61211:2004); German version EN 61211:2005 |
| DIN EN 623-1 | 高級工業陶瓷.塊體陶瓷.一般和結構特性.第1部分:用染色穿透法測定缺陷 | Advanced technical ceramics - Monolithic ceramics; General and textural properties - Part 1: Determination of the presence of defects by dye penetration; German version EN 623-1:2006 |
| DIN EN 623-3 | 高級工業陶瓷.單片陶瓷.總則和結構特性.第3部分:粒度和粒度分布測定(用線性截斷法表征) | Advanced technical ceramics - Monolithic ceramics; General and textural properties - Part 3: Determination of grain size and size distribution (characterized by the linear intercept method); German version EN 623-3:2001 |
| DIN EN 623-4 | 高級工業陶瓷.塊體陶瓷.一般和結構特性.第4部分:表面粗糙度的測定 | Advanced technical ceramics - Monolithic ceramics - General and textural properties - Part 4: Determination of surface roughness; German version EN 623-4:2004 |
| DIN EN 658-1 | 高級工程陶瓷.室溫下陶瓷復合材料的機械性能.第1部分:抗拉性能測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 1: Determination of tensile properties; German version EN 658-1:1998 |
| DIN EN 658-2 | 高級工業陶瓷.陶瓷復合材料室溫機械性能.第2部分:抗壓強度測定 | Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 2: Determination of compression properties; German version EN 658-2:2002 |
| DIN EN 658-4 | 高級工業陶瓷.陶瓷復合材料室溫機械性能.第4部分:通過切口試樣壓縮負荷測定內層剪切強度 | Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 4: Determination of interlaminar shear strength by compression loading of notched test specimens; German version EN 658-4:2003 |
| DIN EN 658-5 | 高級工業陶瓷.陶瓷復合材料室溫機械性能.第5部分:通過瞬間彎曲試驗測定內層剪切強度 | Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 5: Determination of interlaminar shear strength by short span bend test (three-points); German version EN 658-5:2002 |
| DIN EN 725-8 | 高級工業陶瓷.陶瓷粉末試驗方法.第8部分:振實體密度的測定 | Advanced technical ceramics - Methods of test for ceramic powders - Part 8: Determination of tapped bulk density; German version EN 725-8:2006 |
| DIN EN 725-9 | 高級工業陶瓷.陶瓷粉末試驗方法.第9部分:非振實體密度測定 | Advanced technical ceramics - Methods of test for ceramic powders - Part 9: Determination of untapped bulk density; German version EN 725-9:2006 |
| DIN EN 820-1 | 高級工業陶瓷.單片陶瓷試驗方法.熱機械特性.第1部分:高溫撓曲強度測定 | Advanced technical ceramics - Methods of testing monolithic ceramics; Thermo-mechanical properties - Part 1: Determination of flexural strength at elevated temperatures; German version EN 820-1:2002 |
| DIN EN 820-2 | 高級工業陶瓷.整體陶瓷的試驗方法.熱機械特性.第1部分:自重變形的測定 | Advanced technical ceramics - Methods of test for monolithic ceramics - Thermo-mechanical properties - Part 2: Determination of self-loaded deformation; German version EN 820-2:2003 |
| DIN EN 820-3 | 高級工業陶瓷.塊體陶瓷的試驗方法.熱機械特性.第3部分:水淬火法測定耐熱沖擊性 | Advanced technical ceramics - Methods of testing monolithic ceramics - Thermomechanical properties - Part 3: Determination of resistance to thermal shock by water quenching; German version EN 820-3:2004 |
| DIN EN 821-3 | 高級工業陶瓷.整體陶磁.熱物理性能.第3部分:比熱的測定 | Advanced technical ceramics - Monolithic ceramics - Thermo-physical properties - Part 3: Determination of specific heat capacity; German version EN 821-3:2005 |
| DIN EN 843-3 | 高級工業陶瓷.室溫下整體陶瓷的機械特征.第3部分:恒定應力速度撓曲強度試驗中亞臨界斷裂增長參數的測定 | Advanced technical ceramics - Mechanical properties of monolithic ceramics at room temperature - Part 3: Determination of subcritical crack growth parameters from constant stressing rate flexural strength tests; German version EN 843-3:2005 |
| DIN EN 843-4 | 高級工業陶瓷.室溫下整體陶瓷的機械特征.第4部分:維氏、努氏和洛氏表面硬度 | Advanced technical ceramics - Mechanical properties of monolithic ceramics at room temperature - Part 4: Vickers, Knoop and Rockwell superficial hardness; German version EN 843-4:2005 |
| DIN EN ISO 15732 | 細陶瓷(高級陶瓷、高級工業陶瓷).室溫下用單邊預裂束法(SEPB)測定塊體陶瓷破裂韌性的試驗方法 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for fracture toughness of monolithic ceramics at room temperature by single edge precracked beam (SEPB) method (ISO 15732:2003); German version EN ISO 15732:2005 |
| DIN EN ISO 18753 | 精密陶瓷(高級陶瓷、高級工業陶瓷).比重計測定陶瓷粉末的絕對密度 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of absolute density of ceramic powders by pyknometer (ISO 18753:2004); German version EN ISO 18753:2005 |
| DIN EN ISO 18756 | 細陶瓷(高級陶瓷、高級工業陶瓷).用彎曲時的表面裂紋(SCF)法測定室溫下塊體陶瓷的斷裂韌性 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of fracture toughness of monolithic ceramics at room temperature by the surface crack in flexure (SCF) method (ISO 18756:2003); German version EN ISO 18756:2005 |
| DIN EN ISO 18757 | 精密陶瓷(高級陶瓷、高級工業陶瓷).BET法利用氣體吸附來測定陶瓷粉末的比表面積 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of specific surface area of ceramic powders by gas adsorption using the BET method (ISO 18757:2003); German version EN ISO 18757:2005 |
| DIN ISO 6474 | 外科植入物.基于高純度鋁的陶瓷材料 | Implants for surgery - Ceramic materials based on high purity alumina (ISO 6474:1994) |
| DIN V ENV 1006 | 高級工業陶瓷.整體陶瓷.性能評價試樣選擇指南 | Advanced technical ceramics - Monolithic ceramics - Guidance on the selection of test pieces for the evaluation of properties; German version ENV 1006:2003 |
| DIN V ENV 1094-7 | 絕緣耐火制品.第7部分:陶瓷纖維制品的試驗方法; 德文版本 ENV 1094-7:1993 | Insulating refractory products; part 7: methods of test for ceramic fibre products; German version ENV 1094-7:1993 |
| DIN V ENV 12212 | 高級工程陶瓷.統一分級方法 | Advanced technical ceramics - Unified method for classification; German version ENV 12212:1995 |
| DIN V ENV 14232 | 高級工業陶瓷.術語、定義和首字母組合詞 | Advanced technical ceramics - Terms, definitions and abbreviations; Trilingual version ENV 14232:2003 |
| DIN V ENV 658-6 | 高級工業陶瓷.室溫下陶瓷復合材料的機械性能.第6部分:雙沖孔剪切試驗測定剪切強度 | Advanced technical ceramics; mechanical properties of ceramic composites at room temperture; part 6: determination of shear strength by double-punch shearing; german version ENV 658-6:1993 |
| DIN V ENV 820-4 | 高級工業陶瓷.整塊陶瓷試驗方法.熱－機械性能.第4部分:高溫下?lián)闲匀渥冏冃螠y定 | Advanced technical ceramics - Monolithic ceramics; Thermo-mechanical properties - Part 4: Determination of flexural creep deformation at elevated temperatures; German version ENV 820-4:2001 |
| EN 1094-1 | 絕緣耐火產品 第1部分：陶瓷纖維產品術語 | Insulating refractory products - Part 1: Terminology for ceramic fibre products |
| EN 1094-3 | 絕緣耐火產品 第3部分：陶瓷纖維制造的絕緣產品分類 | Insulating refractory products - Part 3: Classification of insulating products made from ceramic fibres |
| EN 50324-1 | 陶瓷材料和部件的壓電特性 第1部分：定義與分類 | Piezoelectric properties of ceramic materials and components - Part 1: Terms and definitions |
| EN 50324-2 | 陶瓷材料和部件的壓電特性 第2部分：測量方法及特性 低功率 | Piezoelectric properties of ceramic materials and components - Part 2: Methods of measurement; Low power |
| EN 50324-3 | 陶瓷材料和部件的壓電特性 第3部分：測量方法高功率 | Piezoelectric properties of ceramic materials and components - Part 3: Methods of measurement; High power |
| ENV 1094-7 | 絕緣耐火產品 第7部分：陶瓷纖維產品試驗方法 | Insulating refractory products - Part 7: Methods of test for ceramic fibre products |
| ENV 12212 | 高級工業陶瓷 統一分類方法 | Advanced technical ceramics - Unified method for classification |
| GB 12651 | 與食物接觸的陶瓷制品鉛、鎘溶出量允許極限 | Standard permissible limits of lead and cadmium release from ceramic ware in contact with food |
| GB 13691 | 陶瓷生產防塵技術規程 | Safety code for the dust protecting technique of the ceramic production |
| GB/T 11309 | 壓電陶瓷材料性能測試方法縱向壓電應變常數d33的準靜態測試 | Test methods for the properties of piezoelectric ceramics--Quasi-static testfor piezoelectric strain content d33 |
| GB/T 11310 | 壓電陶瓷材料性能測試方法相對自由介電常數溫度特性的測試 | Test methods for the properties of piezoelectric ceramics--Test methods for temperature characteristics of relative free dielectric constants |
| GB/T 11311 | 壓電陶瓷材料性能測試方法泊松比σE的測試 | Test methods for the properties of piezoelectric ceramics--Test for Poisson’s ratio σE |
| GB/T 11312 | 壓電陶瓷材料和壓電晶體聲表面波性能測試方法 | Test methods for SAW properties of piezoelectric ceramics and crystals |
| GB/T 11320 | 壓電陶瓷材料性能測試方法低機械品質因數壓電陶瓷材料性能的測試 | Test methods for the properties of piezoelectric ceramics--Material with the low mechanical quality factor |
| GB/T 11387 | 壓電陶瓷材料靜態彎曲強度試驗方法 | Testing method for static flexural strength of piezoellectric ceramics |
| GB/T 13841 | 電子陶瓷件表面粗糙度 | Surface roughness for electronic ceramic parts |
| GB/T 14389 | 工程陶瓷沖擊韌性試驗方法 | Test method for impact toughness of high performance ceramics |
| GB/T 14390 | 工程陶瓷高溫彎曲強度試驗方法 | Test method for flexural strength of highperformance ceramics at elevated temperature |
| GB/T 15155 | 濾波器用壓電陶瓷材料通用技術條件 | Generic specification for piezoelectric ceramic for use in filters |
| GB/T 15750 | 壓電陶瓷材料老化性能試驗規程 | Test program for the ageing properties ofpiezoelectric ceramics |
| GB/T 16528 | 壓敏電阻器用氧化鋅陶瓷材料 | Zinc oxide ceramics for use in varistors |
| GB/T 16533 | 多孔陶瓷產品通用技術條件 | General specification for porous ceramic products |
| GB/T 16534 | 工程陶瓷維氏硬度試驗方法 | Test method for Vickers hardness of high performance ceramics |
| GB/T 16535 | 工程陶瓷線熱膨脹系數試驗方法 | Test method for linear thermal expansion of high performance ceramics |
| GB/T 16536 | 工程陶瓷抗熱震性試驗方法 | Test method for thermal shock resistance of high performance ceramics |
| GB/T 17911 | 耐火材料陶瓷纖維制品試驗方法 | Refractory products - Methods of test for ceramic fibre products |
| GB/T 17991 | 工業陶瓷及相關術語 | Definitions of terms relating to industrial ceramics |
| GB/T 2413 | 壓電陶瓷材料體積密度測量方法 | Piezoelectric ceramic materials--Measuring methods for determination of volume density |
| GB/T 2414.1 | 壓電陶瓷材料性能試驗方法圓片徑向伸縮振動模式 | Test methods for the properties of piezoelectric ceramics--Radial extension vibration mode for disk |
| GB/T 2414.2 | 壓電陶瓷材料性能試驗方法長條橫向長度伸縮振動模式 | Test methods for the properties of piezoelectric ceramics--Transverse length extension vibration mode for bar |
| GB/T 3003 | 耐火材料陶瓷纖維及制品 | Refractory - Ceramic fibre and the products |
| GB/T 3295 | 陶瓷制品45°鏡向光澤度試驗方法 | Standard test method for 45°specular gloss of ceramic ware |
| GB/T 3388 | 壓電陶瓷材料型號命名方法 | Designations for types of piezoelectric ceramics |
| GB/T 3389.2 | 壓電陶瓷材料性能測試方法縱向壓電應變常數d33的靜態測試 | Testmethods for the properties of piezoelectric ceramics--Static test for piezoelectric strain constant d33 |
| GB/T 3389.3 | 壓電陶瓷材料性能試驗方法居里溫度TC的測試 | Test methods for the properties of piezoelectric ceramics test for Curie temperature TC |
| GB/T 3389.4 | 壓電陶瓷材料性能測試方法柱體縱向長度伸縮振動模式 | Test methods for the properties of piezoelectric ceramics--Longitudinal length extension vibration mode for rod |
| GB/T 3389.5 | 壓電陶瓷材料性能測試方法圓片厚度伸縮振動模式 | Test methods for the properties of piezoelectric ceramics--Thickness extension vibration mode for disk |
| GB/T 3389.6 | 壓電陶瓷材料性能測試方法長方片厚度切變振動模式 | Test methods for the properties of piezoelectric ceramics--Thickness-shear vibration mode for rectangular plate |
| GB/T 3389.7 | 壓電陶瓷材料性能測試方法強場介電性能的測試 | Test methods for the properties of piezoelectric ceramics--Test for dielectric properties in high electric field |
| GB/T 3389.8 | 壓電陶瓷材料性能測試方法熱釋電系數的測試 | Test methods for the properties of piezoelectric ceramics--Test for the pyroelectric coefficient |
| GB/T 4308 | 金屬陶瓷熱擠壓模坯 | Cermet hot extrusion die blank |
| GB/T 4734 | 陶瓷材料及制品化學分析方法 | Methods of chemical analysis for ceramic materials and articles |
| GB/T 4738.1 | 日用陶瓷材料耐酸、耐堿性能測定方法 (塊狀法) | Standard test method for acid， alkaline resistance for ceramic materials of daily use (lump test method) |
| GB/T 4738.2 | 日用陶瓷材料耐酸、耐堿性能測定方法 (顆粒法) | Standard test method for acid， alkaline resistance for ceramic materials of daily use (particle test method) |
| GB/T 4740 | 陶瓷材料抗壓強度試驗方法 | Standard test method for compressive resistance ceramic materials |
| GB/T 4741 | 陶瓷材料抗彎曲強度試驗方法 | Standard test method for bending strength of ceramic materials |
| GB/T 5593 | 電子元器件結構陶瓷材料 | Structure ceramic materials used in electronic components |
| GB/T 5594.1 | 電子元器件結構陶瓷材料性能測試方法氣密性測試方法 | Test methods for properties of structure ceramic used in electronic components--Test method for gas-tightness |
| GB/T 5594.2 | 電子元器件結構陶瓷材料性能測試方法楊氏彈性模量、泊松比測試方法 | Test methods for properties of structure ceramic used in electronic components--Test method for Youngs elastic modulus and Poisson ratio |
| GB/T 5594.3 | 電子元器件結構陶瓷材料性能測試方法平均線膨脹系數測試方法 | Test methods for properties of structure ceramic used in electronic components--Test methodfor mean coefficient of linear expansion |
| GB/T 5594.4 | 電子元器件結構陶瓷材料性能測試方法介質損耗角正切值的測試方法 | Test methods for properties of structure ceramic used in electronic components--Test method for dielectric loss angle tangent value |
| GB/T 5594.5 | 電子元器件結構陶瓷材料性能測試方法體積電阻率測試方法 | Test methods for properties of structure ceramic used in electronic components--Test method forvolume resistivity |
| GB/T 5594.6 | 電子元器件結構陶瓷材料性能測試方法化學穩定性測試方法 | Test methods for properties of structure ceramic used in electronic components--Test method forchemical durability |
| GB/T 5594.7 | 電子元器件結構陶瓷材料性能測試方法透液性測定方法 | Test methods for properties of structure ceramic used in electronic components--Test method for liquid permeability |
| GB/T 5594.8 | 電子元器件結構陶瓷材料性能測試方法顯微結構的測定 | Test methods for properties of structure ceramic used in electronic components--Determination of microstructure |
| GB/T 6426 | 鐵電陶瓷材料電滯回線的準靜態測試方法 | Quasi-static test method for ferroelectric hysteresis loop of ferroelectric ceramics |
| GB/T 9587 | 陽極耗散功率大于1kW的金屬陶瓷發射管空白詳細規范(可供認證用) | Blank detail specification for metal ceramic transmitting tubes of anode dissipation over 1kW |
| HG/T 3210 | 耐酸陶瓷材料性能試驗方法 | () |
| IEC 60168 Edition 4.2 | 標稱電壓大于1000V的系統用陶瓷材料或玻璃的戶內和戶外柱式絕緣子試驗 | Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1000 V |
| IEC 60591 | 公稱電壓高于1000v的架空線路用陶瓷材料或玻璃絕緣子采用統計控制方法進行機械和機電試驗時的取樣規則和驗 | Sampling rules and acceptance criteria when applying statistical control methods for mechanical and electromechanical tests on insulators of ceramic material or glass for overhead lines with a nominal voltage greater than 1 000 V |
| ISO 10635 | 耐火制品 陶瓷纖維制品的試驗方法 | Refractory products - Methods of test for ceramic fibre products |
| ISO 13356 | 外科植入物 含有穩定氧化釔的四方形氧化鋯陶瓷材料 | Implants for surgery - Ceramic materials based on yttria-stabilized tetragonal zirconia (Y-TZP) |
| ISO 14704 Technical Corrigendum 1 | 精細陶瓷(高級陶瓷、高級工業陶瓷).室溫下塊體陶瓷彎曲強度的試驗方法.技術勘誤1 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for flexural strength of monolithic ceramics at room temperature; Technical Corrigendum 1 |
| ISO 15732 | 精細陶瓷(高級陶瓷、高級工業陶瓷).室溫下用單邊預裂束法(SEPB)測定塊體陶瓷破裂韌性的試驗方法 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for fracture toughness of monolithic ceramics at room temperature by single edge precracked beam (SEPB) method |
| ISO 17561 | 精細陶瓷(高級陶瓷、高級工業陶瓷).室溫下通過聲共振對整塊陶瓷彈性模量的試驗方法 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for elastic moduli of monolithic ceramics at room temperature by sonic resonance |
| ISO 17565 | 細陶瓷(高級陶瓷、高級工業陶瓷).高溫下塊體陶瓷彎曲強度的試驗方法 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for flexural strength of monolithic ceramics at elevated temperature |
| ISO 18452 | 精密陶瓷(高級陶瓷、高級工業陶瓷).用接觸式探針輪廓測定儀測定陶瓷覆層厚度 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of thickness of ceramic films by contact-probe profilometer |
| ISO 18753 | 精細陶瓷(高級陶瓷、高級工業陶瓷).用比重計測定陶瓷粉末的絕對密度 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of absolute density of ceramic powders by pyknometer |
| ISO 18754 | 精細陶瓷(高級陶瓷和高級工業陶瓷).密度和表觀孔隙率的測定 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of density and apparent porosity |
| ISO 18755 | 細陶瓷(高級陶瓷、高級工業陶瓷).用激光閃光法測定塊體陶瓷的熱擴散 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of thermal diffusivity of monolithic ceramics by laser flash method |
| ISO 18756 | 細陶瓷(高級陶瓷、高級工業陶瓷).用彎曲時的表面裂紋(SCF)法測定室溫下塊體陶瓷的斷裂韌性 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of fracture toughness of monolithic ceramics at room temperature by the surface crack in flexure (SCF) method |
| ISO 18757 | 細陶瓷(高級陶瓷、高級工業陶瓷).利用BET法通過氣體吸收率測定陶瓷粉末的比表面積 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of specific surface area of ceramic powders by gas adsorption using the BET method |
| ISO 20501 | 細陶瓷(高級陶瓷、高級工業陶瓷).強度數據的維伯統計 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Weibull statistics for strength data |
| ISO 20502 | 細陶瓷(高級陶瓷、高級工業陶瓷).用劃痕試驗測定陶瓷涂層的粘附性 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of adhesion of ceramic coatings by scratch testing |
| ISO 20504 | 精細陶瓷(高級陶瓷、高級工業陶瓷).在室溫下連續纖維增強復合材料的壓縮特性試驗方法 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for compressive behaviour of continuous fibre-reinforced composites at room temperature |
| ISO 20505 | 精密陶瓷(高級陶瓷、高級工業陶瓷).用雙凹口試件擠壓和Iosipescu試驗在環境溫度下連續纖維增強復合材料層間 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of the interlaminar shear strength of continuous-fibre-reinforced composites at ambient temperature by the compression of double-notched test pieces and by the Iosipescu test |
| ISO 20506 | 細陶瓷(高級陶瓷、高級工業陶瓷).在室溫下用Iosipescu試驗測定連續纖維增強復合材料的面內剪切強度 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of the in-plane shear strength of continuous-fibre-reinforced composites at ambient temperature by the Iosipescu test |
| ISO 20507 | 細陶瓷(高級陶瓷、高級工業陶瓷).詞匯 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Vocabulary |
| ISO 20508 | 細陶瓷(高級陶瓷、高級工業陶瓷).有透明襯底的陶瓷膜的透光系數的測定 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of light transmittance of ceramic films with transparent substrate |
| ISO 20509 | 細陶瓷(高級陶瓷、高級工業陶瓷).非氧化塊體陶瓷的抗氧化性測定 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of oxidation resistance of non-oxide monolithic ceramics |
| ISO 20808 | 精細陶瓷(高級陶瓷、高級工業陶瓷).用球盤法測定塊體陶瓷的摩擦和磨損特性 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of friction and wear characteristics of monolithic ceramics by ball-on-disc method |
| ISO 22214 | 精細陶瓷(高級陶瓷、高級工業陶瓷).室溫下單片陶瓷周期性彎曲疲勞的試驗方法 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for cyclic bending fatigue of monolithic ceramics at room temperature |
| ISO 22215 | 精細陶瓷(高級陶瓷、高級工業陶瓷).單片陶瓷拉伸蠕變試驗方法 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for tensile creep of monolithic ceramics |
| ISO 24369 | 細陶瓷(高級陶瓷、高級工業陶瓷).用濕篩分法測定陶瓷粉末的粗晶粒含量 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of content of coarse particles in ceramic powders by wet sieving method |
| ISO 24370 | 細陶瓷(高級陶瓷、高級工業陶瓷).室溫下用鋸齒形切口試桿(CNB)法測定單片陶瓷斷裂韌性的試驗方法 | Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for fracture toughness of monolithic ceramics at room temperature by chevron-notched beam (CNB) method |
| ISO 6474 | 外科植入物 高純氧化鋁陶瓷材料 | Implants for surgery; ceramic materials based on high purity alumina |
| ISO 6486-1 | 與食物接觸的陶瓷制品、玻璃陶瓷制品和玻璃餐具 鉛、鎘溶出量 第1部分:檢驗方法 | Ceramic ware, glass-ceramic ware and glass dinnerware in contact with food - Release of lead and cadmium - Part 1: Test method |
| ISO 6486-2 | 與食物接觸的陶瓷制品、玻璃陶瓷制品和玻璃餐具 鉛、鎘溶出量 第2部分:允許極限 | Ceramic ware, glass-ceramic ware and glass dinnerware in contact with food - Release of lead and cadmium - Part 2: Permissible limits |
| ISO/TTA 1 | 高級工業陶瓷 統一分類體系 | Advanced technical ceramics - Unified classification system |
| JB/T 10111 | 滅弧罩陶瓷件及其材料 | () |
| JB/T 6829 | 金屬陶瓷X 射線管 技術條件 | () |
| JC/T 897 | 抗菌陶瓷制品抗菌性能 | () |
| JIS A5207 | 衛生陶瓷制品 | Sanitary wares |
| JIS H8306 | 金屬陶瓷熱噴鍍 | Cermet thermal spraying |
| JIS H8667 | 金屬陶瓷噴鍍涂層的試驗方法 | Test methods for cermet sprayed coatings |
| JIS H9303 | 金屬陶瓷噴鍍涂層的推薦規程 | Recommended practice for cermet sprayed coatings |
| JIS R1657 | 連續纖維增強陶瓷基質復合材料用連續陶瓷纖維的測試方法 | Testing methods of continuous ceramic fibers for continuous fiber-reinforced ceramic matrix composites |
| JIS R1701-1 | 精細陶瓷(高級陶瓷、高級工業陶瓷).光催化材料的空氣凈化性能試驗方法.第1部分:氧化氮的清除 | Fine ceramics (advanced ceramics, advanced technical ceramics) -- Test method for air purification performance of photocatalytic materials -- Part 1: Removal of nitric oxide |
| JIS R3311 | 陶瓷纖維氈 | Ceramic fiber blanket |
| JIS T6118 | 金屬陶瓷的牙科修復系統.貴金屬 | Metal-ceramic dental restorative systems -- Precious metals |
| JIS T6120 | 金屬陶瓷牙科修復系統.試驗方法 | Metal-ceramic dental restorative systems -- Test methods |
| JIS T6121 | 金屬陶瓷牙科修復系統.金屬 | Metal-ceramic dental restorative systems -- Metals |
| NF A92-801-1 | 高級工業陶瓷.陶瓷覆層的試驗方法.第1部分:用接觸式探針輪廓測定儀測定覆層厚度 | (Advanced technical ceramics - Methods of test for ceramic coatings - Part 1 : determination of coating thickness by contact probe filometer.) |
| NF A92-801-2 | 高級工程陶瓷.陶瓷覆層的試驗方法.第2部分:用環形研磨法測定覆層厚度 | (Advanced technical ceramics - Methods of test for ceramic coatings - Part 2 : determination of coating thickness by the crater grinding method.) |
| NF B40-010 | 耐火制品.第1部分:陶瓷纖維制品的術語(歐洲標準EN 1094-1) | (INSULATING REFRACTORY PRODUCTS. PART 1 : TERMINOLOGY FOR CERAMIC FIBRE PRODUCTS. (EUROPEAN STANDARD EN 1094-1).) |
| NF B41-204 | 工程陶瓷.單片陶瓷.一般特征和結構特征.第3部分:粒度和粒徑分布的測定(用線性截斷法表征) | (Advanced technical ceramics - Monolithic ceramics - General and textural properties - Part 3 : determination of grain size and size distribution (characterized by the linear intercept method).) |
| NF B41-210-1 | 高級工業陶瓷.整體陶瓷的試驗方法.熱機械特性.第1部分:高溫下?lián)锨鷱姸鹊臏y定 | (Advanced technical ceramics - Methods of testing monolithic ceramics - Thermomechanical properties - Part 1 : determination of flexural strength at elevated temperatures.) |
| NF B41-210-2 | 高級工業陶瓷.整體陶瓷的試驗方法.熱機械特性.第2部分:自重變形的測定 | (Advanced technical ceramics - Methods of testing monolithic ceramics - Thermo-mechanical properties - Part 2 : determination of self-loaded deformation.) |
| NF B42-006 | 高級工業陶瓷.陶瓷粉末試驗方法.第6部分:比表面積的測定 | (Advanced technical ceramics. Methods of test for ceramic powders. Part 6 : determination of the specific surface area.) |
| NF B42-007 | 高級工業陶瓷.陶瓷粉末的試驗方法.第7部分:絕對密度的測定 | (Advanced technical ceramics. Methods of test for ceramic powders. Part 7 : determination of the absolute density.) |
| NF B42-012 | 高級工程陶瓷.陶瓷粉末的試驗方法.第12部分:鋯氧土的化學分析 | (Advanced technical ceramics - Methods of test for ceramic powders - Part 12 : chemical analysis of zirconia.) |
| NF B43-202 | 高級工業陶瓷.室溫下陶瓷復合材料的機械性能.第2部分:抗壓性能的測定 | (Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 2 : determination of compression properties.) |
| NF B43-203 | 高級工業陶瓷.室溫下陶瓷合成材料的機械特性.第3部分:抗彎強度的測定 | (Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 3 : determination of flexural strength.) |
| NF B43-204 | 高級工業陶瓷.室溫下陶瓷復合材料的機械性能.第4部分:通過對切口試樣的壓縮負荷測定內層的剪切強度 | (Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 4 : determination of interlaminar shear strength by compression loading of notched test specimens.) |
| NF B43-205 | 高級工業陶瓷.室溫下陶瓷復合材料的機械性能.第5部分:利用瞬間彎曲試驗測定內層狀剪切強度(三點法) | (Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 5 : determination of interlaminar shear strength by short span bend test (three points).) |
| NF B43-207 | 高級工業陶瓷.陶瓷復合材料.熱物理性能.第1部分:熱膨脹的測定 | (Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 1 : determination of thermal expansion.) |
| NF B43-210 | 高級工業陶瓷.陶瓷復合材料的熱物理性能.第3部分:比熱的測定 | (Advanced technical ceramics - Ceramic composites, thermophysical properties - Part 3 : determination of specific heat capacity.) |
| NF B43-303 | 高級工業陶瓷.陶瓷復合材料在高溫、大氣壓和空氣中的機械性能.壓縮性能的測定 | (Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature in air at atmospheric pressure - Determination of compression properties.) |
| NF B43-305 | 高級工業陶瓷.在大氣壓力下高溫時陶瓷復合物的機械特性.撓曲強度的測定 | (Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under air at atmospheric pressure - Determination of flexural strength.) |
| NF C26-501-1 | 陶瓷材料和元件的壓電特性.第1部分:術語和定義 | (Piezoelectric properties of ceramic materials and components - Part 1 : terms and definitions.) |
| NF C26-501-2 | 陶瓷材料和元件的壓電特性.第2部分:低功率測量方法 | (Piezoelectric properties of ceramic materials and components - Part 2 : methods of measurement - Low power.) |
| NF C26-501-3 | 陶瓷材料和元件的壓電特性.第3部分:高功率測量方法 | (Piezoelectric properties of ceramic materials and components - Part 3 : properties and methods of measurement - High power.) |
| NF D14-601 | 衛生設備.涂釉的衛生陶瓷制品.一般技術規范 | (SANITARY APPLIANCES. VITREOUS ENAMELLED SANITARY CERAMIC. GENERAL SPECIFICATIONS.) |
| NF D21-631 | 與食品接觸的材料和物品.陶瓷材料半透明性試驗方法(歐洲標準EN 184) | (Materials and articles in contact with foodstuffs. Test methods for translucency of ceramic articles.) |
| NF S90-408 | 外科醫療器械.外科植入物.氧化鋁陶瓷制品 | (MEDICAL AND SURGICAL EQUIPMENT. IMPLANTS FOR SURGERY. CERAMIC MATERIALS BASED ON ALUMINA.) |
| NF S91-233 | 牙科金屬陶瓷修補材料 | (Metal-ceramic dental restorative systems.) |
| NF S94-063 | 外科植入物.釔穩定處理的四方形鋯基陶瓷材料 | (Implants for surgery. Ceramic materials based on yttria-stabilized tetragonal zirconia (Y-TZP).) |
| NF T25-710 | 高級工業陶瓷.增強度試驗方法.第1部分:測定尺寸范圍 | (Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 1 : determination of size content.) |
| NF T25-711 | 高級工業陶瓷.陶瓷合成材料.第2部分:測定線性密度 | (Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 2 : determination of linear density.) |
| NF T25-712 | 高級工業陶瓷.陶瓷合成材料.第3部分:測定線直徑和截面面積 | (Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 3 : determination of filament diameter and cross-section area.) |
| NF T25-715 | 高級工業陶瓷.陶瓷復合材料.增強纖維的試驗方法.第5部分:室溫下復絲束中長絲拉伸強度分布和斷裂時拉伸應變 | (Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Part 5 : determination of distribution of tensile strength and of tensile strain to failure of filaments within) |
| QB/T 1010 | 陶瓷材料、顏料真密度的測定 | () |
| QB/T 1321 | 陶瓷材料平均線熱膨脹系數測定方法 | () |
| QB/T 1547 | 陶瓷材料燒法溫度范圍測定方法 | () |
| SH/T 3128 | 一般煉油裝置火焰加熱爐陶瓷纖維襯里 | () |
| YS/T 518 | 金屬陶瓷熱擠壓模坯 | () |
| 編號 | 中文名稱 | 英文名稱 |